Xiangyu Liao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiangyu Liao has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Junhui Hu
Guangxi Normal University
4 shared publications Chuanyang Huang
3 shared publications- Jian Tang
Guangxi Normal University
3 shared publications Lianghua Chen
Guangxi Normal University
3 shared publicationsQiunan Zhang
Guangxi Normal University
3 shared publicationsZhenbo Yan
3 shared publications
Latest Publications
- 1 September 2026
- Published by IOP Publishing in Journal of Optics
- Vol. 28 (9) , 095704
High-sensitivity tilt sensor based on a cascaded core-offset and spherical single-mode fiber interferometer
A high-sensitivity fiber-optic tilt sensor based on Mach–Zehnder interference is proposed. The design uses a controlled core-offset to excite higher-order cladding modes in a few-mode fiber (FMF) and incorporates a spherical structure to enhance intermodal coupling efficiency. This configuration yields high fringe contrast and provides a sensitive, monotonic response to tilt angle variation. The influences of FMF length on the free spectral range, core-offset higher-order modes excitation, and spherical structure diameter on interference fringe contrast were systematically investigated. Experimental results demonstrated that, over a tilt range from 15.26° to 32.47°, the sensor achieves a sensitivity as high as −5.07 nm/°, while the temperature sensitivity is only 0.03 nm°C −1 between 24 °C and 36 °C. The corresponding temperature cross-sensitivity is as low as 0.006°/°C. The combination of high tilt responsivity and suppressed thermal crosstalk makes the sensor well suited for stable operation in complex environments and suggests strong potential for deformation monitoring of engineering structures.
- 1 September 2026
- Published by IOP Publishing in Journal of Optics
- Vol. 28 (9) , 095704
High-sensitivity tilt sensor based on a cascaded core-offset and spherical single-mode fiber interferometer
A high-sensitivity fiber-optic tilt sensor based on Mach–Zehnder interference is proposed. The design uses a controlled core-offset to excite higher-order cladding modes in a few-mode fiber (FMF) and incorporates a spherical structure to enhance intermodal coupling efficiency. This configuration yields high fringe contrast and provides a sensitive, monotonic response to tilt angle variation. The influences of FMF length on the free spectral range, core-offset higher-order modes excitation, and spherical structure diameter on interference fringe contrast were systematically investigated. Experimental results demonstrated that, over a tilt range from 15.26° to 32.47°, the sensor achieves a sensitivity as high as −5.07 nm/°, while the temperature sensitivity is only 0.03 nm°C −1 between 24 °C and 36 °C. The corresponding temperature cross-sensitivity is as low as 0.006°/°C. The combination of high tilt responsivity and suppressed thermal crosstalk makes the sensor well suited for stable operation in complex environments and suggests strong potential for deformation monitoring of engineering structures.
- Open Access
- 7 April 2026
- Published by Elsevier in SSRN Electronic Journal
A Low-Temperature Crosstalk and High-Sensitivity Optical Fiber Current Sensor Based on Core-Offset Single-Mode Fiber and Gourd-Shaped Single-Mode Fiber
A low-temperature cross-talk and high-sensitivity optical fiber current sensor is proposed, which consists of core-offset single-mode fiber-gourd-shaped single-mode fiber (COS-GSS). The compact gourd-shaped structure can continuously and efficiently excite the energy of the coupled mode optical field, thus enhancing the sensitivity to external variations. By bonding the sensing region to a chromium-nickel wire, the current flowing through it generates Joule heating, which significantly shifts the wavelength of the interference dip and realizes current sensing. Experimental investigations were carried out to analyze the effects of the single-mode fiber (SMF) interferometer arm length, core-offset distance, GSS cladding diameter, and chromium-nickel wire length on the sensing sensitivity. The results demonstrate that the sensor exhibits a high current-square (A2) sensitivity of 3.65 nm/A2, an ultra-low temperature cross-talk of 0.0186 A2/oC, and excellent measurement stability. It shows promising application potential in current monitoring for DC transmission systems and current measurement in strong magnetic field environments.
- 7 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Low-Temperature Crosstalk and High-Sensitivity Optical Fiber Current Sensor Based on Core-Offset Single-Mode Fiber and Gourd-Shaped Single-Mode Fiber
A low-temperature cross-talk and high-sensitivity optical fiber current sensor is proposed, which consists of core-offset single-mode fiber-gourd-shaped single-mode fiber (COS-GSS). The compact gourd-shaped structure can continuously and efficiently excite the energy of the coupled mode optical field, thus enhancing the sensitivity to external variations. By bonding the sensing region to a chromium-nickel wire, the current flowing through it generates Joule heating, which significantly shifts the wavelength of the interference dip and realizes current sensing. Experimental investigations were carried out to analyze the effects of the single-mode fiber (SMF) interferometer arm length, core-offset distance, GSS cladding diameter, and chromium-nickel wire length on the sensing sensitivity. The results demonstrate that the sensor exhibits a high current-square (A2) sensitivity of 3.65 nm/A2, an ultra-low temperature cross-talk of 0.0186 A2/oC, and excellent measurement stability. It shows promising application potential in current monitoring for DC transmission systems and current measurement in strong magnetic field environments.
- Open Access
- 2 March 2026
- Published by Elsevier in SSRN Electronic Journal
Design of a Fiber-Optic Voltage Sensor with Offset-Induced Orientation Independence and Tunable Sensitivity
An indirect voltage sensing approach based on Joule heating and Ohm’s law is presented through the development of a core-offset fiber-optic interferometric structure. By introducing two ellipsoidal units with unequal diameters, the sensor eliminates sensitivity to offset orientation while preserving strong modal coupling. The diameter-difference configuration enables a single core-offset to replicate the functional behavior of conventional dual-offset systems, thereby simplifying fabrication and improving mechanical robustness. Sensitivity tuning is achieved by adjusting the resistance of the CrNi heating wire via length modification, providing flexible control over thermal response. Numerical simulations reveal progressive energy transfer from the fundamental mode to higher-order modes within the ellipsoidal transition region, accompanied by a gradual reduction in output optical power. Experimental investigations confirm that the interferometer arm length governs the free spectral range (FSR), the ellipsoid diameter dictates modal-energy redistribution and sensing performance, and the offset magnitude primarily regulates fringe visibility rather than sensitivity. The device demonstrates a linear voltage sensitivity of 12.25 nm/V and a voltage-squared sensitivity of 0.76 nm/V2, corresponding to an equivalent current-squared sensitivity of 3.68 nm/A2. Temperature-induced crosstalk is limited to 0.32 V/°C, and the steady-state thermal variation remains within 2.11 °C under constant bias conditions. Owing to its structural simplicity, directional independence, and tunable sensitivity, the proposed sensor offers practical value for power-supply supervision in avionics instrumentation, communication and navigation systems, and battery management platforms.
- 2 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDesign of a Fiber-Optic Voltage Sensor with Offset-Induced Orientation Independence and Tunable Sensitivity
An indirect voltage sensing approach based on Joule heating and Ohm’s law is presented through the development of a core-offset fiber-optic interferometric structure. By introducing two ellipsoidal units with unequal diameters, the sensor eliminates sensitivity to offset orientation while preserving strong modal coupling. The diameter-difference configuration enables a single core-offset to replicate the functional behavior of conventional dual-offset systems, thereby simplifying fabrication and improving mechanical robustness. Sensitivity tuning is achieved by adjusting the resistance of the CrNi heating wire via length modification, providing flexible control over thermal response. Numerical simulations reveal progressive energy transfer from the fundamental mode to higher-order modes within the ellipsoidal transition region, accompanied by a gradual reduction in output optical power. Experimental investigations confirm that the interferometer arm length governs the free spectral range (FSR), the ellipsoid diameter dictates modal-energy redistribution and sensing performance, and the offset magnitude primarily regulates fringe visibility rather than sensitivity. The device demonstrates a linear voltage sensitivity of 12.25 nm/V and a voltage-squared sensitivity of 0.76 nm/V2, corresponding to an equivalent current-squared sensitivity of 3.68 nm/A2. Temperature-induced crosstalk is limited to 0.32 V/°C, and the steady-state thermal variation remains within 2.11 °C under constant bias conditions. Owing to its structural simplicity, directional independence, and tunable sensitivity, the proposed sensor offers practical value for power-supply supervision in avionics instrumentation, communication and navigation systems, and battery management platforms.
- 1 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (19) , 36131-36138
Fiber Vector Torsion Sensor With Low Crosstalk for Temperature and Strain Based on Mach–Zehnder Interference
A Mach-Zehnder interferometer (MZI) based on a polarization-maintaining fiber-few-mode fiber (PMF-FMF) structure is proposed to achieve high-sensitivity vector torsion sensing. The effects of fiber lengths, core offset directions, and offset magnitudes of both PMF and FMF on the interference spectra are investigated. Leveraging the properties of PMF, when the sensor is twisted, changes in the polarization state of the transmitted light alter the intensity of interference dips, causing the wavelengths of the envelope valleys to shift in opposite directions, which enables the discrimination of torsion direction. Additionally, the influence of PMF and FMF lengths on the interference spectra is studied, and experimental measurements of torsion, temperature, and strain sensing are conducted. Experimental results show that the maximum torsion sensitivity for clockwise (CW) rotation is 0.91 nm/(rad/m), and that for counterclockwise (CCW) rotation is -0.61 nm/(rad/m). Additionally, the sensor features simple fabrication, low sensitivity to strain and temperature interference, and a measurement error of less than 4%. These characteristics make it highly suitable for structural health monitoring applications in civil engineering and aerospace industries.
- 1 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (19) , 36131-36138
Fiber Vector Torsion Sensor With Low Crosstalk for Temperature and Strain Based on Mach–Zehnder Interference
A Mach-Zehnder interferometer (MZI) based on a polarization-maintaining fiber-few-mode fiber (PMF-FMF) structure is proposed to achieve high-sensitivity vector torsion sensing. The effects of fiber lengths, core offset directions, and offset magnitudes of both PMF and FMF on the interference spectra are investigated. Leveraging the properties of PMF, when the sensor is twisted, changes in the polarization state of the transmitted light alter the intensity of interference dips, causing the wavelengths of the envelope valleys to shift in opposite directions, which enables the discrimination of torsion direction. Additionally, the influence of PMF and FMF lengths on the interference spectra is studied, and experimental measurements of torsion, temperature, and strain sensing are conducted. Experimental results show that the maximum torsion sensitivity for clockwise (CW) rotation is 0.91 nm/(rad/m), and that for counterclockwise (CCW) rotation is -0.61 nm/(rad/m). Additionally, the sensor features simple fabrication, low sensitivity to strain and temperature interference, and a measurement error of less than 4%. These characteristics make it highly suitable for structural health monitoring applications in civil engineering and aerospace industries.