Mohd Rodhi Sahid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mohd Rodhi Sahid has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Al Takrouri
Universiti Teknologi Malaysia
3 shared publications - Ahmed Alanssari
Department of Electrical Power Engineering, Faculty of Electrical Engineering, Universiti Teknologi Malaysia (UTM), Skudai 81310, Malaysia
2 shared publications - Farag Elghabsi
Department of Electrical Power Engineering, Faculty of Electrical Engineering, Universiti Teknologi Malaysia (UTM), Skudai 81310, Malaysia
2 shared publications - Razman Ayop
Universiti Teknologi Malaysia
2 shared publications - Abdulhakeem Mohammed Dobi
Department of Electrical Engineering, Waziri Umaru Federal Polytechnic, Birnin Kebbi, Nigeria
1 shared publication - Firdaus Ishak1 shared publication
Latest Publications
- 30 April 2026
- Published by Penerbit UTM Press in ELEKTRIKA- Journal of Electrical Engineering
- Vol. 25 (1) , 27-34
Comparative Metaheuristic Optimization for Sizing Grid-Connected Hybrid Renewable Systems: A Libya Case Study
Hybrid renewable energy system (HRE) sizing is vital for maximizing both economic and environmental performance in grid-connected systems. This study develops a comparative optimization framework for an HRE serving a camp in the southeastern region of Libya, integrating photovoltaic (PV) arrays, wind turbines (WT), battery storage systems (BT), fuel cells (FC), hydrogen tanks (HT) and an Electrolyzer (EL). Three objective functions, Levelized Cost of Energy (LCOE), Grid Reliance Fraction (GRF) and Pollutant Emission Coefficient (PEC), are employed to quantify techno-economic efficiency and environmental impact. To this end, three widely used metaheuristic algorithms; Particle Swarm Optimization (PSO), Genetic Algorithm (GA) and Grey Wolf Optimizer (GWO), are employed under identical settings to identify optimal system configurations. Each algorithm is run for a fixed number of iterations, and their diversity and convergence behaviors are monitored to ensure a fair benchmark. The comparative results show that PSO yields the most cost-effective design, achieving an LCOE of $0.1448/kWh, a reduction of 13.5% and 1.3% relative to GA and GWO, respectively and a GRF of 15.73%. These findings demonstrate that PSO strikes the best balance between cost, reliability and computational efficiency for this HRE case study. The framework and insights presented here can guide planners and engineers in selecting the most suitable optimization method for sustainable energy-system design.
- 30 April 2026
- Published by Penerbit UTM Press in ELEKTRIKA- Journal of Electrical Engineering
- Vol. 25 (1) , 27-34
Comparative Metaheuristic Optimization for Sizing Grid-Connected Hybrid Renewable Systems: A Libya Case Study
Hybrid renewable energy system (HRE) sizing is vital for maximizing both economic and environmental performance in grid-connected systems. This study develops a comparative optimization framework for an HRE serving a camp in the southeastern region of Libya, integrating photovoltaic (PV) arrays, wind turbines (WT), battery storage systems (BT), fuel cells (FC), hydrogen tanks (HT) and an Electrolyzer (EL). Three objective functions, Levelized Cost of Energy (LCOE), Grid Reliance Fraction (GRF) and Pollutant Emission Coefficient (PEC), are employed to quantify techno-economic efficiency and environmental impact. To this end, three widely used metaheuristic algorithms; Particle Swarm Optimization (PSO), Genetic Algorithm (GA) and Grey Wolf Optimizer (GWO), are employed under identical settings to identify optimal system configurations. Each algorithm is run for a fixed number of iterations, and their diversity and convergence behaviors are monitored to ensure a fair benchmark. The comparative results show that PSO yields the most cost-effective design, achieving an LCOE of $0.1448/kWh, a reduction of 13.5% and 1.3% relative to GA and GWO, respectively and a GRF of 15.73%. These findings demonstrate that PSO strikes the best balance between cost, reliability and computational efficiency for this HRE case study. The framework and insights presented here can guide planners and engineers in selecting the most suitable optimization method for sustainable energy-system design.
- Open Access
- 16 October 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
High gain and high efficiency soft switching quadratic boost converter for renewable energy applications
Quadratic boost converter (QBC) is crucial in immediate technologies, including renewable energy, electric vehicles (EV), DC microgrids and EV charging stations, where efficient and dependable power conversion is essential. This article introduces a high-gain, high-efficiency QBC operating with soft-switching capabilities explicitly tailored for renewable energy sources that can be used in charging stations for EVs. The design achieves high voltage gain (VGN) by incorporating a coupled inductor (CIN) with a restricted duty cycle, which minimizes the need for extreme duty cycle adjustments that often impact efficiency and cause component stress. The leakage inductances of the CIN’s enable zero voltage switching (ZVS) for the power switches at turn-on and ZVS turn-on and zero current switching (ZCS) turn-off for the diodes. This approach mitigates the switches’ losses and enhances the efficiency. Furthermore, an active clamp circuit is employed, allowing the converter to operate with reduced voltage stress across semiconductor components, thus improving their durability and reliability. The converter operated in continuous conduction mode (CCM) is extensively analysed to assess its performance across various operating conditions. This converter compares VGN, efficiency, and stress on components with several recent QBCs for a comprehensive performance assessment. The converter’s 250 W hardware prototype has also been built and tested, demonstrating its practical suitability and effectiveness for high-demand renewable energy applications. Experimental findings affirm the converter’s high efficiency and reliable performance in real-world situation.
- 16 October 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Open AccessHigh gain and high efficiency soft switching quadratic boost converter for renewable energy applications
Quadratic boost converter (QBC) is crucial in immediate technologies, including renewable energy, electric vehicles (EV), DC microgrids and EV charging stations, where efficient and dependable power conversion is essential. This article introduces a high-gain, high-efficiency QBC operating with soft-switching capabilities explicitly tailored for renewable energy sources that can be used in charging stations for EVs. The design achieves high voltage gain (VGN) by incorporating a coupled inductor (CIN) with a restricted duty cycle, which minimizes the need for extreme duty cycle adjustments that often impact efficiency and cause component stress. The leakage inductances of the CIN’s enable zero voltage switching (ZVS) for the power switches at turn-on and ZVS turn-on and zero current switching (ZCS) turn-off for the diodes. This approach mitigates the switches’ losses and enhances the efficiency. Furthermore, an active clamp circuit is employed, allowing the converter to operate with reduced voltage stress across semiconductor components, thus improving their durability and reliability. The converter operated in continuous conduction mode (CCM) is extensively analysed to assess its performance across various operating conditions. This converter compares VGN, efficiency, and stress on components with several recent QBCs for a comprehensive performance assessment. The converter’s 250 W hardware prototype has also been built and tested, demonstrating its practical suitability and effectiveness for high-demand renewable energy applications. Experimental findings affirm the converter’s high efficiency and reliable performance in real-world situation.
- Open Access
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 117571-117581
A High-Voltage-Gain Non-Isolated Dual-Input Single-Output Soft-Switching DC–DC Converter With Low-Voltage Stress
Multiple input non-isolated dc-dc converters remain very popular in applications involving hybrid energy integration. This is due to their compact structure and low cost in comparison with their isolated topologies counterparts. This paper proposed a high voltage gain high efficiency, soft-switching dual-input single-output dc-dc converter with low voltage stress for hybrid energy integration. The proposed converter achieves soft-switching for all the power switches at turn-on instants alongside high voltage conversion ratio. The coupled inductor is designed to facilitate ZVS and achieve high voltage gain eliminating the need for additional auxiliary circuits. This reduces the converter cost, number of components count and enhances efficiency. Furthermore, the voltage across the power switch is clamped with the help of an active clamp network. This facilitates the use of switches with low drain-to-source resistance (Rds on) hence reducing conduction losses and increasing the efficiency. Similarly, the operating modes of the converter as well as comparison with other similar converters are presented. In addition, experimental results obtained for 250 W prototype are presented which converts an input of 24 V dc to a 250 V dc at the output terminal with 97.8% efficiency.
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 117571-117581
Open AccessA High-Voltage-Gain Non-Isolated Dual-Input Single-Output Soft-Switching DC–DC Converter With Low-Voltage Stress
Multiple input non-isolated dc-dc converters remain very popular in applications involving hybrid energy integration. This is due to their compact structure and low cost in comparison with their isolated topologies counterparts. This paper proposed a high voltage gain high efficiency, soft-switching dual-input single-output dc-dc converter with low voltage stress for hybrid energy integration. The proposed converter achieves soft-switching for all the power switches at turn-on instants alongside high voltage conversion ratio. The coupled inductor is designed to facilitate ZVS and achieve high voltage gain eliminating the need for additional auxiliary circuits. This reduces the converter cost, number of components count and enhances efficiency. Furthermore, the voltage across the power switch is clamped with the help of an active clamp network. This facilitates the use of switches with low drain-to-source resistance (Rds on) hence reducing conduction losses and increasing the efficiency. Similarly, the operating modes of the converter as well as comparison with other similar converters are presented. In addition, experimental results obtained for 250 W prototype are presented which converts an input of 24 V dc to a 250 V dc at the output terminal with 97.8% efficiency.