Alex Cosmin Niculescu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alex Cosmin Niculescu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Mihalache Ghinea
National University of Science and Technology POLITEHNICA Bucharest, Romania
3 shared publications - Bogdan Dragos Rosca
Department of Robots and Manufacturing Systems, Faculty of Industrial Engineering and Robotics, National University of Science and Technology Politehnica Bucharest, 060042 Bucharest, Romania
2 shared publications - Claudia Borda
Quality Engineering and Industrial Technologies, National University of Science and Technology Politehnica Bucharest, Splaiul Independentei Nr. 313, 060042 Bucharest, Romania, Romania
1 shared publication - Dan Nitoi
National University of Science and Technology POLITEHNICA Bucharest , Bucharest , Romania
1 shared publication - Ioana Catalina Enache
Department of Engineering Graphics and Industrial Design, National University of Science and Technology Politehnica Bucharest, Splaiul Independenței, Nr. 313, 060042 Bucharest, Romania
1 shared publication - Marilena Gheorghe
Quality Engineering and Industrial Technologies, National University of Science and Technology Politehnica Bucharest, Splaiul Independentei Nr. 313, 060042 Bucharest, Romania
1 shared publication
Latest Publications
- Open Access
- 9 December 2025
- Published by MDPI AG in Preprints.org
Increasing the Working Speed During Wire Drawing by Ultrasonic Activation of the Die
Ultrasound applications are currently a very intense field of research, always in expansion, constantly finding new uses for them in all scientific fields. The basic process investigated in this research is that of obtaining wires by wire-drawing technology, which consists of successively passing a semi-finished wire through a sequence of dies until the desired final diameter is obtained. This plastic deformation process usually takes place at room temperature. The phenomena that can still be studied in this process and improved is that of reducing the friction between two parts that are in relative motion named also “ultrasonic lubrication”. Based on this phenomenon, technology for obtaining metal wires by wire drawing can be improved by increasing the wiredrawing speed. The article presents the design and calculation of the ultrasonic transducer used to activate the drawing die, the FEM to determine the optimal vibration frequencies and vibration modes used in activation of the die. To demonstrate the effect of reducing the coefficient of friction during wire drawing, a test stand was used in which the pulling force is achieved by a pneumatic system and the die is one of those used in a wire production factory. By ultrasonic activation of the die, an increase in the working speed was obtained. The percentage increase in the drawing speed is different, depending on the initial traction speed.
- 9 December 2025
- Published by MDPI AG in Preprints.org
Open AccessIncreasing the Working Speed During Wire Drawing by Ultrasonic Activation of the Die
Ultrasound applications are currently a very intense field of research, always in expansion, constantly finding new uses for them in all scientific fields. The basic process investigated in this research is that of obtaining wires by wire-drawing technology, which consists of successively passing a semi-finished wire through a sequence of dies until the desired final diameter is obtained. This plastic deformation process usually takes place at room temperature. The phenomena that can still be studied in this process and improved is that of reducing the friction between two parts that are in relative motion named also “ultrasonic lubrication”. Based on this phenomenon, technology for obtaining metal wires by wire drawing can be improved by increasing the wiredrawing speed. The article presents the design and calculation of the ultrasonic transducer used to activate the drawing die, the FEM to determine the optimal vibration frequencies and vibration modes used in activation of the die. To demonstrate the effect of reducing the coefficient of friction during wire drawing, a test stand was used in which the pulling force is achieved by a pneumatic system and the die is one of those used in a wire production factory. By ultrasonic activation of the die, an increase in the working speed was obtained. The percentage increase in the drawing speed is different, depending on the initial traction speed.
- Open Access
Enhancing FDM Rapid Prototyping for Industry 4.0 Applications Through Simulation and Optimization Techniques
Modern manufacturing is increasingly shaped by the paradigm of Industry 4.0 (Smart Manufacturing). As one of its nine pillars, additive manufacturing plays a crucial role, enabling high-quality final products with improved profitability in minimal time. Advances in this field have facilitated the emergence of diverse technologies—such as Fused Deposition Modelling (FDM), Stereolithography (SLA), and Selective Laser Sintering (SLS)—allowing the use of metallic, polymeric, and composite materials. Within this context, Klipper v.0.12, an open-source firmware for 3D printers, addresses the performance limitations of conventional consumer-grade systems. By offloading computationally intensive tasks to an external single-board computer (e.g., Raspberry Pi), Klipper enhances speed, precision, and flexibility while reducing prototyping time. The purpose of this study is twofold: first, to identify and analyze bottlenecks in low-cost 3D printers and second, to evaluate how these shortcomings can be mitigated through the integration of supplementary hardware and software (Klipper firmware, Raspberry Pi, additional sensors, and the Mainsail interface). The scientific contribution of this study lies in demonstrating that a consumer-grade FDM 3D printer can be significantly upgraded through this integration and systematic calibration, achieving up to a 50% reduction in printing time while maintaining dimensional accuracy and improving surface quality.
Open AccessEnhancing FDM Rapid Prototyping for Industry 4.0 Applications Through Simulation and Optimization Techniques
Modern manufacturing is increasingly shaped by the paradigm of Industry 4.0 (Smart Manufacturing). As one of its nine pillars, additive manufacturing plays a crucial role, enabling high-quality final products with improved profitability in minimal time. Advances in this field have facilitated the emergence of diverse technologies—such as Fused Deposition Modelling (FDM), Stereolithography (SLA), and Selective Laser Sintering (SLS)—allowing the use of metallic, polymeric, and composite materials. Within this context, Klipper v.0.12, an open-source firmware for 3D printers, addresses the performance limitations of conventional consumer-grade systems. By offloading computationally intensive tasks to an external single-board computer (e.g., Raspberry Pi), Klipper enhances speed, precision, and flexibility while reducing prototyping time. The purpose of this study is twofold: first, to identify and analyze bottlenecks in low-cost 3D printers and second, to evaluate how these shortcomings can be mitigated through the integration of supplementary hardware and software (Klipper firmware, Raspberry Pi, additional sensors, and the Mainsail interface). The scientific contribution of this study lies in demonstrating that a consumer-grade FDM 3D printer can be significantly upgraded through this integration and systematic calibration, achieving up to a 50% reduction in printing time while maintaining dimensional accuracy and improving surface quality.
- Open Access
- 4 August 2025
- Published by MDPI AG in Preprints.org
Enhancing FDM Rapid Prototyping for Industry 4.0 Applications through Simulation and Optimisation Techniques
Modern production systems increasingly rely on Industry 4.0 technologies, also known as Smart Manufacturing. Among its foundational pillars, additive manufacturing plays a critical role in enabling rapid prototyping and the creation of customised final products with minimal cost and lead time. Key technologies such as Fused Deposition Modelling (FDM), Stereolithography (SLA), and Selective Laser Sintering (SLS) have expanded material capabilities to include plastics, metals, and composites. This study focuses on the implementation of Klipper, an open-source firmware developed to improve 3D printing performance by delegating computational processes to an external microcontroller. A comparative experimental setup was designed using an ordinary printer to evaluate improvements in print speed, dimensional accuracy, and surface quality. The research identifies performance bottlenecks in standard, affordable 3D printers and demonstrates how computer app integration enhances both efficiency and quality. The findings position this kind of computer app as a viable solution for improving the prototyping workflow in cost-sensitive environments, contributing to the broader adoption of advanced manufacturing practices aligned with Industry 4.0 principles.
- 4 August 2025
- Published by MDPI AG in Preprints.org
Open AccessEnhancing FDM Rapid Prototyping for Industry 4.0 Applications through Simulation and Optimisation Techniques
Modern production systems increasingly rely on Industry 4.0 technologies, also known as Smart Manufacturing. Among its foundational pillars, additive manufacturing plays a critical role in enabling rapid prototyping and the creation of customised final products with minimal cost and lead time. Key technologies such as Fused Deposition Modelling (FDM), Stereolithography (SLA), and Selective Laser Sintering (SLS) have expanded material capabilities to include plastics, metals, and composites. This study focuses on the implementation of Klipper, an open-source firmware developed to improve 3D printing performance by delegating computational processes to an external microcontroller. A comparative experimental setup was designed using an ordinary printer to evaluate improvements in print speed, dimensional accuracy, and surface quality. The research identifies performance bottlenecks in standard, affordable 3D printers and demonstrates how computer app integration enhances both efficiency and quality. The findings position this kind of computer app as a viable solution for improving the prototyping workflow in cost-sensitive environments, contributing to the broader adoption of advanced manufacturing practices aligned with Industry 4.0 principles.