RDRuta W. Deusdedith

Ruta W. Deusdedith

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ruta W. Deusdedith has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Mahmoud A. Ali

    Xuefeng Mountain Energy Equipment Safety National Observation and Research Station, School of Electrical Engineering, Chongqing University, Chongqing, China

    4 shared publications
  • Khatri Nirajan

    School of Electrical Engineering, State Key Laboratory of Power Transmission Equipment System Security New Technology, Chongqing University, Shapingba District, Chongqing City, P.R. China

    3 shared publications
  • Xingliang Jiang

    Xuefeng Mountain Energy Equipment Safety National Observation and Research Station, Chongqing University, Chongqing 400044, China

    3 shared publications
  • Feipeng Wang

    State Key Laboratory of Power Transmission Equipment Technology, Chongqing University, Chongqing, China

    1 shared publication
  • Hualong Zheng

    Xuefeng Mountain Energy Equipment Safety National Observation and Research Station, Chongqing University, Chongqing 400044, China

    1 shared publication
  • Muhammad Abdul Rahim

    School of Materials Science and Engineering, Chongqing University, Shapingba, District, Chongqing City, P.R. China

    1 shared publication

Latest Publications

  • Open Access

    Enhancing Hydrophobic Stability of Silicone Rubber Insulators Under High‐Voltage Direct Current Stress Through Optimised Nano‐Fumed Silica Surface Area: A Dynamic Drop Test Study

    by Mahmoud A. Ali, Xingliang Jiang, Samir I. Gadow, Ruta W. Deusdedith

    The long‐term hydrophobic stability of silicone rubber (SiR) insulators is essential for their reliability in high‐voltage direct current (HVDC) applications. This study investigates the effect of nano‐silica fillers with varying specific surface areas (SSA = 120, 200 and 300 m 2 /g) and different concentrations of alumina trihydrate (ATH) fillers (5–50 wt.%) on the dynamic hydrophobicity of SiR using the dynamic drop test (DDT) under HVDC stress. Key performance indicators—hydrophobicity retention, recovery and transfer—were evaluated. Experimental results indicate that nano‐silica, particularly with an SSA of 200 m 2 /g, (SFS200) significantly improves hydrophobic performance, offering the best balance of retention time, recovery, transfer and reproducibility. In contrast, high ATH loadings hinder the migration of low molecular weight and reduce recovery. Moderate ATH content (10 wt.%) showed optimal performance among ATH‐filled samples but was still inferior to silica‐filled composites. Although higher SSA enhanced retention time, an excessively high SSA (300 m 2 /g) resulted in agglomeration and consequently reduced recovery. These results confirm the superiority of fumed silica in improving the hydrophobic stability of SiR insulators and highlight the critical role of filler characteristics—particularly SSA, porosity and dispersion—in optimising SiR performance under HVDC stress. The study also demonstrates that additional experimental precautions improved DDT reproducibility, supporting its use in future standardisation.


  • Modulating Structure and Properties of P(VDF-HFP)/Co 3 O 4 Nanocomposites with 2D Nanofillers

    by Khatri Nirajan, Wang Feipeng, Muhammad Abdul Rahim, Ruta W. Deusdedith, Mahmoud A. Ali

    Poly (vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) is a strongly promising fluoropolymer because of outstanding flexibility, electrochemical consistency, and excellent dielectric property, making it promising material for dielectric and electronic applications. Nanocomposite films composed of P(VDF-HFP) and varying-concentration of 2D Co3O4 nano mesh are synthesized via spin-coating process. Mechanical, structural, morphological, dielectric, electrical characteristics of the nanocomposites are comprehensively studied. The FTIR and XRD analysis confirms the retention of electroactive β-phase and successful incorporation of Co3O4 nano mesh into polymer matrix with strong interfacial interactions. SEM study reveals a uniform dispersion at lower loadings and agglomeration at higher loadings. Mechanical testing shows that Young’s modulus increases from 123.05 MPa (0.0 wt.%) to 959.92 MPA (4.0 wt.%). Dielectric analysis reveals significant enhanced permittivity as the temperature increases for all nanocomposite films. AC conductivity also improves significantly with filler content, frequency and temperature. At 30 °C σac rises from 1.65 x 10-8 S/cm for 0.0 wt.% to 6.99 x10-3 S/cm for 7.0 wt.% composite at 107 Hz. The 4.0 wt.% sample shows a peak σac of 1.11 x 10-2 S/cm, indicating enhanced charge transport due to interfacial polarization and filler-induced conduction pathways. These results indicate that Co3O4 nanomesh effectively tunes the mechanical and dielectric response of P(VDF-HFP), although excessive loading leads to aggregation and higher dielectric loss.

  • Surface Degradation Performance of 2D Nanosheets-Filled Silicone Rubber Insulator under DC Tracking and Erosion Stress

    by Mahmoud A. Ali, Xingliang Jiang, Hualong Zheng, Xiaolong Zhang, Khatri Nirajan, Ruta W. Deusdedith

    This study investigates the surface degradation behavior of silicone rubber (SiR) composites filled with two-dimensional (2D) nanosheets—molybdenum disulfide (MoS₂) and tungsten disulfide (WS₂)—under high-voltage direct current (HVDC) tracking and erosion stress. Using standardized DC inclined plane testing (IEC 60587, IEEE Std 2652™-2021), the performance of 2D-filled composites is compared with conventional fillers, including aluminum trihydrate (ATH) and fumed silica, at a fixed loading of 5 wt.%. Key parameters such as eroded mass, track length, erosion depth, leakage current, thermal conductivity, and thermal stability are evaluated. Results show that 2D nanosheets significantly reduce erosion and tracking length, maintain lower and more stable surface temperatures, and enhance thermal stability compared to neat SiR and spherical-filler composites. MoS₂ and WS₂ fillers demonstrate superior performance, attributed to their high aspect ratios, layered morphology, and strong interfacial bonding with the SiR matrix, which promote tortuous thermal/electrical pathways and thermally stable char formation. The findings highlight the effectiveness of 2D nanofillers in developing advanced, erosion-resistant silicone rubber insulators for HVDC environments and underscore the critical role of filler morphology in optimizing DC tracking and erosion performance.

  • Investigation of Castor Oil Influence on DC Surface Flashover Voltage Characteristics of Epoxy Resin Insulators

    by Ruta W. Deusdedith, Xingliang Jiang, Mahmoud A. Ali, Khatri Nirajan, Zeng Dong

    The utilization of epoxy resin insulators for high voltage insulation continues to expand; however, surface flashover remains its significant challenge. Conventional methods for improving surface flashover voltage in epoxy insulators basically focus on physical and chemical changes while neglecting environmental and sustainability concerns involving petroleum epoxy resins. In this study, eco-friendly castor oil is incorporated into the epoxy matrix to enhance surface flashover voltage while promoting reduction of overreliance on finite petroleum resources. The successful integration of castor oil into the epoxy matrix is confirmed by Fourier Transform Infrared Spectroscopy, whereas the Atomic Force Microscopy and Scanning Electron Microscopy reveal smooth surfaces of composites at relatively low concentrations of castor oil, while higher concentrations beyond 30% lead to an increase in roughness. Samples’ relative permittivities are analyzed by using a Novocontrol spectrometer, which reveals the decrease in relative permittivity with the addition of castor oil into epoxy matrix. Notably, the positive and negative flashover voltages are enhanced by 17.47% and 18.49% respectively, at a castor oil concentration of 30 wt% with respect to epoxy resin, which is attributed to moderate trap parameters alongside favorable charge carrier mobility. These findings suggest that epoxy-castor oil biocomposite is a potential high voltage insulation material with reduced petroleum quantity and enhanced flashover voltage.