AKAlexei A. Kozlov

Alexei A. Kozlov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Alexei A. Kozlov has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Damage-growth performance in multilayer dielectric mirrors under 351-nm, 1-ns laser pulses: influence of design parameters

    by Marek Stehlik, Brittany N. Hoffman, Hu Huang, Alexei A. Kozlov, Sara MacNally, Kyle R. P. Kafka, Kestutis Juskevicius, Amy L. Rigatti, Stavros G. Demos

    Multilayer dielectric (MLD) mirrors are critical for next-generation, large-aperture, high-repetition-rate laser systems, such as inertial fusion energy drivers or directed energy systems. The performance of MLD mirrors must remain unaffected by laser-induced damage over their operational lifetime. This study investigates the material and design parameters that influence the damage-growth performance of fabricated Al 2 O 3 /SiO 2 and HfO 2 /SiO 2 MLD mirrors tested at 351 nm using nanosecond pulses. The study is based on the hypothesis that damage initiation can be considered unavoidable due to coating imperfections or contamination, but may not affect laser operation if damage sites remain stable with successive pulses. Modeling of damage-initiation sites revealed that the 3D electric-field intensity governs damage growth. Results show that high-index material significantly affects the damage-growth threshold. Using a high-index material as the outer layer helps confine damage growth to this layer, preventing catastrophic penetration into inner layers.

  • Scalable waveplate for ultraviolet applications using laser-imprinted birefringence in silica

    by Sergei Shevtsov, M. Mireles, K. R. P. Kafka, Marek Stehlik, Alexei Kozlov, Yuhao Lei, Yuriy Svirko, Jonathan Zuegel, P. G. Kazansky, Stavros Demos

    A method for fabrication of large-aperture waveplate suitable for operation in the near-ultraviolet spectral region is demonstrated. The waveplate was fabricated using femtosecond direct laser writing of bulk fused silica. This method enables the precise control of the induced birefringence, which is introduced via the generation of nanopores with geometrical features that are controlled by the laser processing parameters. The resulting structures also introduce a small loss of transmission that is on the order of 4% at 351 nm. The laser-induced–damage threshold in the nanosecond regime was found to approach that of the native fused-silica substrate, which makes it a suitable candidate for polarization control in laser fusion research applications.


  • Laser-induced damage-growth threshold at 351 nm in the nanosecond regime in dielectric coatings employing different high-index materials

    by Marek Stehlik, Alexei A. Kozlov, Kyle R. P. Kafka, Brittany N. Hoffman, Sara MacNally, Amy L. Rigatti, Stavros G. Demos

    The laser-damage performance of HfO2/SiO2 and Al2O3/SiO2 mirrors was investigated at a laser wavelength of 351 nm with nanosecond pulse durations. A method was developed to quantify the laser-induced damage-growth threshold under conditions relevant to high-repetition-rate, large-aperture laser systems. The results suggest that the damage-growth performance cannot be inferred from the corresponding damage-initiation threshold that is commonly used to evaluate the performance of optical materials. A systematic difference was also observed in the performance between these two groups of high-index materials, with the Al2O3/SiO2 mirrors exhibiting about twofold improvement in the damage-growth threshold.


  • Enhancing the performance of solvent-borne poly(ethyl methacrylate) coatings for high-power laser applications via low-temperature drying

    by Nathaniel D. Urban, Marek Stehlik, Alexei A. Kozlov, Marcela Mireles, Jenny F. Zhao, Brittany N. Hoffman, Dylan B. Rykert, John C. Lambropoulos, Kenneth L. Marshall, Stavros G. Demos

    Organic polymers are a versatile class of materials employed in a broad range of optical coating applications. However, their use as coatings in high-power laser applications, particularly in the UV spectral region, has been limited in scope due to their relatively low laser-induced damage thresholds (LIDTs), which decrease further with exposure to multiple pulses. This study explores the effect of post-deposition drying temperature and residual solvent on the LIDT of solvent-borne polymer coatings. In this work, poly(ethyl methacrylate) (PEMA) coatings were deposited by first spin coating solutions of PEMA (dissolved in 2,2,2-trichloroethanol (TCE)) onto fused silica substrates, then baking at temperatures of either 130°C (soft-bake) or 180°C (hard-bake). Analysis of the two coatings revealed that the soft-bake coating retained a significant amount of TCE within the polymer matrix, which functioned to plasticize the coating and reduce internal stress. The laser-induced damage resistance of the two coatings was evaluated using 351-nm, 1-ns laser pulses. The testing protocols included single-pulse (1-on-1), 1-pulse ramp (R-on-1), and a 1000-pulse ramp (1000R-on-1) test. The results showed that the plasticized, soft-bake coating exhibits a significantly increased LIDT, especially for multipulse irradiation conditions.

  • Long-term monitoring the damage performance of multilayer dielectric grating samples residing inside the compressor chamber of the OMEGA EP laser

    by Alexei A. Kozlov, Stavros G. Demos, David Canning, Brian E. Kruschwitz, Leon J. Waxer, Brittany N. Hoffman, Amy L. Rigatti, Nickolaos Savidis

    Understanding of the laser-induced damage threshold and impact of air–vacuum cycling of the optical components in short-pulse laser systems is of fundamental importance. We report the results of a damage-testing campaign that monitored representative pulse compression grating samples that were positioned inside the OMEGA EP grating compressor vacuum chamber during normal operation and routinely damage tested on every quarterly vent for a period of about 10 years. The evolution of their damage resistance under 10-ps and 100-ps pulse lengths are associated with a significant degradation of the laser-induced damage thresholds, which is comparatively larger at 100 ps, is described.


  • Open Access

    Round-robin measurements of the laser-induced damage threshold with sub-picosecond pulses on optical single layers

    by Laurent Lamaignère, Alexandre Ollé, Marine Chorel, Nadja Roquin, Alexei A. Kozlov, Brittany N. Hoffman, James B. Oliver, Stavros G. Demos, Laurent Gallais, Raluca A. Negres, et al.

    The standardization and comparison of laser-damage protocols and results are essential prerequisites for development and quality control of large optical components used in high-power laser facilities. To this end, the laser-induced–damage thresholds of two different coatings were measured in a round-robin experiment involving five well-equipped damage testing facilities. Investigations were conducted at the wavelength of 1 μm in the sub picosecond pulse duration range with different configurations in terms of polarization, angle of incidence, and environment (air versus vacuum). In this temporal regime, the damage threshold is known to be deterministic, i.e., the continuous probability distribution transitions from 0 to 1 over a very narrow fluence range. This in turn implies that the damage threshold can be measured very precisely. These characteristics enable direct comparison of damage-threshold measurements between different facilities, with the difference in the measured values indicating systematic errors or other parameters that were not previously appreciated. The results of this work illustrate the challenges associated with accurately determining the damage threshold in the short-pulse regime. Specifically, the results of this round-robin damage-testing effort exhibited significant differences between facilities. The factors to be taken into account when comparing the results obtained with different test facilities are discussed: temporal and spatial profiles, environment, damage detection, sample homogeneity, and nonlinear beam propagation.


  • Role of HfO2/SiO2thin-film interfaces in near-ultraviolet absorption and pulsed laser damage

    by Semyon Papernov, Alexei A. Kozlov, James B. Oliver, Chris Smith, Lars Jensen, Stefan Günster, Heinrich Mädebach, Detlev Ristau

    The role of thin-film interfaces in the near-ultraviolet (near-UV) absorption and pulsed laser-induced damage was studied for ion-beam-sputtered and electron-beam-evaporated coatings comprised from HfO2 and SiO2 thin-film pairs. To separate contributions from the bulk of the film and from interfacial areas, absorption and damage threshold measurements were performed for a one-wave (355-nm wavelength) thick, HfO2 single-layer film and for a film containing seven narrow HfO2 layers separated by SiO2 layers. The seven-layer film was designed to have a total optical thickness of HfO2 layers, equal to one wave at 355 nm and an E-field peak and average intensity similar to a single-layer HfO2 film. Absorption in both types of films was measured using laser calorimetry and photothermal heterodyne imaging. The results showed a small contribution to total absorption from thin-film interfaces as compared to HfO2 film material. The relevance of obtained absorption data to coating near-UV, nanosecond-pulse laser damage was verified by measuring the damage threshold and characterizing damage morphology. The results of this study revealed a higher damage resistance in the seven-layer coating as compared to the single-layer HfO2 film in both sputtered and evaporated coatings. The results are explained through the similarity of interfacial film structure with structure formed during the codeposition of HfO2 and SiO2 materials.


  • Open Access

    Near-ultraviolet absorption annealing in hafnium oxide thin films subjected to continuous-wave laser radiation

    by Semyon Papernov, Alexei A. Kozlov, James B. Oliver, Terrance J. Kessler, Alexander Shvydky, Brendan Marozas

    Hafnium oxide (HfO2) is the most frequently used high-index material in multilayer thin-film coatings for high-power laser applications ranging from near-infrared to near-ultraviolet (UV). Absorption in this high-index material is also known to be responsible for nanosecond-pulse laser-damage initiation in multilayers. In this work, modification of the near-UV absorption of HfO2 monolayer films subjected to irradiation by continuous-wave (cw), 355-nm or 351-nm laser light focused to produce power densities of the order of ∼100 kW/cm2 is studied. Up to a 70% reduction in absorption is found in the areas subjected to irradiation. Temporal behavior of absorption is characterized by a rapid initial drop on the few-tens-of-seconds time scale, followed by a longer-term decline to a steady-state level. Absorption maps generated by photothermal heterodyne imaging confirm the permanent character of the observed effect. Nanosecond-pulse, 351-nm and 600-fs, 1053-nm laser-damage tests performed on these cw laser–irradiated areas confirm a reduction of absorption by measuring up to 25% higher damage thresholds. We discuss possible mechanisms responsible for near-UV absorption annealing and damage-threshold improvement resulting from irradiation by near-UV cw laser light.