Vyshnav Kannampalli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vyshnav Kannampalli has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Lionel Santinacci
Aix Marseille Univ., CNRS, CINaM, Marseille, France
2 shared publications - Anjana Devi
Leibniz Institute for Solid State and Materials Research
1 shared publication - Antoine Seyeux
CNRS—Chimie ParisTech PSL University, Institut de Recherche de Chimie Paris, Physical Chemistry of Surfaces Group, Paris 75005, France
1 shared publication - Bruno Fabre
Univ Rennes CNRS ISCR (Institut des Sciences Chimiques de Rennes) – UMR 6226 Rennes France
1 shared publication - Clémence Badie
Aix Marseille Univ, CNRS, CINaM, Marseille, France
1 shared publication - Hazar Guesmi
Institut Charles Gerhardt Montpellier
1 shared publication
Latest Publications
- Open Access
- 4 November 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (2) , 971-987
Atomic layer deposition of NiO x : harnessing the potential of new precursor combinations for photoelectrochemical water oxidation
Atomic layer deposition enables the fabrication of uniform, conformal, and pinhole-free thin films with precise sub-nanometer thickness control. This work presents the first report of thermal ALD of NiOx using two nickel precursors –Alanis™ and [Ni(ipki)2]– in combination with two different oxidising agents (H2O and O3), over a temperature range of 75-250°C. The Alanis/O3 composition exhibited one of the highest growth per cycle (1.2Å) and a broad ALD window between 100-175°C. In contrast, the Alanis/H2O and [Ni(ipki)2]/O3 combinations yielded lower growth rates of 0.74Å at 150°C and 0.40Å at 250°C, respectively. Comprehensive structural, morphological, optical, and chemical characterisations revealed that the choice of precursor combination and the reaction temperature significantly impact the film composition, strongly influencing its suitability for various applications. Notably, those parameters closely determined the photoelectrochemical performance and the stability of the Si/NiOx-based photoanode towards oxygen evolution reaction. Photoelectrodes fabricated with Alanis/O3 at 200°C demonstrate stability exceeding 24H and exhibit a remarkable OER onset potential of 1.15V vs RHE for a photocurrent density of 1mA·cm-2.
- 4 November 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (2) , 971-987
Open AccessAtomic layer deposition of NiO x : harnessing the potential of new precursor combinations for photoelectrochemical water oxidation
Atomic layer deposition enables the fabrication of uniform, conformal, and pinhole-free thin films with precise sub-nanometer thickness control. This work presents the first report of thermal ALD of NiOx using two nickel precursors –Alanis™ and [Ni(ipki)2]– in combination with two different oxidising agents (H2O and O3), over a temperature range of 75-250°C. The Alanis/O3 composition exhibited one of the highest growth per cycle (1.2Å) and a broad ALD window between 100-175°C. In contrast, the Alanis/H2O and [Ni(ipki)2]/O3 combinations yielded lower growth rates of 0.74Å at 150°C and 0.40Å at 250°C, respectively. Comprehensive structural, morphological, optical, and chemical characterisations revealed that the choice of precursor combination and the reaction temperature significantly impact the film composition, strongly influencing its suitability for various applications. Notably, those parameters closely determined the photoelectrochemical performance and the stability of the Si/NiOx-based photoanode towards oxygen evolution reaction. Photoelectrodes fabricated with Alanis/O3 at 200°C demonstrate stability exceeding 24H and exhibit a remarkable OER onset potential of 1.15V vs RHE for a photocurrent density of 1mA·cm-2.
- Open Access
- 11 July 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
Atomically bridged palladium between nickel species and carbon microfibers and the subsequent conversion into free-standing and electrocatalytically active multifunctional electrodes
We introduce free-standing multifunctional electrodes created by combining the atomic layer deposition of palladium and nickel oxide nanostructures directly onto gas diffusion electrodes with thermal treatment, to form nanostructured electrocatalysts.
- 11 July 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
Open AccessAtomically bridged palladium between nickel species and carbon microfibers and the subsequent conversion into free-standing and electrocatalytically active multifunctional electrodes
We introduce free-standing multifunctional electrodes created by combining the atomic layer deposition of palladium and nickel oxide nanostructures directly onto gas diffusion electrodes with thermal treatment, to form nanostructured electrocatalysts.