Ramya Maranan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ramya Maranan has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jaspreet Kaur
Kanya Maha Vidyalaya College
1 shared publication - Ketan Rathor
GyanSys Inc.,Department of PMO,Maharashtra,India
1 shared publication - Lakshmaiya Natrayan
Department of Mechanical Engineering, Saveetha School of Engineering, SIMATS, Chennai, India
1 shared publication - Pratheesh Krishnankutty
Engineering Department (Mechanical and Industrial Unit), University of Technology and Applied Sciences — Muscat, P. O. Box 74, Al-Khuwair, Sultanate of Oman
1 shared publication S. Kaliappan
Lovely Professional University,Division of Research and Development,Phagwara,Punjab,India
1 shared publication- Seeniappan Kaliappan
Department of Mechanical Engineering, KCG College of Technology, Karapakkam, Chennai 600 097, Tamil Nadu, India
1 shared publication
Latest Publications
- 28 July 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
MECHANICAL, TRIBOLOGICAL, FATIGUE, AND CREEP PERFORMANCE OF AA 7075 COMPOSITES REINFORCED WITH ANNEALED AND FUNCTIONALIZED BIOSILICA FROM RED MATTA RICE HUSK
The effects of heat-treated biosilica from red matta rice husk added to AA7075 metal matrix composites are the subject of this study. Matrix fabrication was carried out using the stir casting method. Specimens were subsequently characterized according to ASTM standards, covering mechanical, fatigue, dry and wet sliding behavior, and creep strain properties. Among the different designations produced, AA2 stands out as showing especially promising mechanical and fatigue properties. With an impact energy of 32.8[ ]J, a yield strength of 241[ ]MPa, a fatigue strength of 318[ ]MPa, and a tensile strength of 547[ ]MPa, AA2 is quite impressive. This classification emphasizes the beneficial effect of biosilica incorporation on the mechanical and fatigue properties of the composite. AA3, which contains 5[ ]wt.% biosilica, exhibits decreased creep strain and improved wear resistance in dry and wet sliding situations. The coefficient of friction (COF) is 0.57, and the specific wear rate is 0.018[ ]mm3/Nm for dry sliding wear, as shown in AA3. The specific wear rate in wet sliding wear is 0.007[ ]mm3/Nm, and there is a COF of 0.55. The biosilica, which is derived from red matta rice husk, acts as a reinforcing agent, improving the matrix’s microstructural stability and load transfer capabilities. At 2000, 4000, 6000, 8000, and 10,000[ ]s, respectively, AA3 shows reduced creep strain values of 0.0102, 0.02494, 0.0994, 0.221, and 0.379. Applications requiring exceptional fatigue performance, mechanical strength, and wear resistance should benefit from biosilica-reinforced AA7075 composites, according to this study. The results provide important information for developing new materials with better overall performance.
- 28 July 2025
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
MECHANICAL, TRIBOLOGICAL, FATIGUE, AND CREEP PERFORMANCE OF AA 7075 COMPOSITES REINFORCED WITH ANNEALED AND FUNCTIONALIZED BIOSILICA FROM RED MATTA RICE HUSK
The effects of heat-treated biosilica from red matta rice husk added to AA7075 metal matrix composites are the subject of this study. Matrix fabrication was carried out using the stir casting method. Specimens were subsequently characterized according to ASTM standards, covering mechanical, fatigue, dry and wet sliding behavior, and creep strain properties. Among the different designations produced, AA2 stands out as showing especially promising mechanical and fatigue properties. With an impact energy of 32.8[ ]J, a yield strength of 241[ ]MPa, a fatigue strength of 318[ ]MPa, and a tensile strength of 547[ ]MPa, AA2 is quite impressive. This classification emphasizes the beneficial effect of biosilica incorporation on the mechanical and fatigue properties of the composite. AA3, which contains 5[ ]wt.% biosilica, exhibits decreased creep strain and improved wear resistance in dry and wet sliding situations. The coefficient of friction (COF) is 0.57, and the specific wear rate is 0.018[ ]mm3/Nm for dry sliding wear, as shown in AA3. The specific wear rate in wet sliding wear is 0.007[ ]mm3/Nm, and there is a COF of 0.55. The biosilica, which is derived from red matta rice husk, acts as a reinforcing agent, improving the matrix’s microstructural stability and load transfer capabilities. At 2000, 4000, 6000, 8000, and 10,000[ ]s, respectively, AA3 shows reduced creep strain values of 0.0102, 0.02494, 0.0994, 0.221, and 0.379. Applications requiring exceptional fatigue performance, mechanical strength, and wear resistance should benefit from biosilica-reinforced AA7075 composites, according to this study. The results provide important information for developing new materials with better overall performance.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 7-12
Technological Evaluation and Software Bug Training using Genetic Algorithm and Time Convolution Neural Network (GA-TCN)
One crucial step in addressing bugs is assigning a proper severity rating to each report. New bugs are being reported at such a high rate that the bug repository has grown significantly in size. The bug triaging procedure has become more subjective as the size of the bug repository has grown. Therefore, the bug triaging procedure requires a classification of the severity of a problem report. Several machine learning approaches to automatically rank bugs by severity have been proposed. These system performance falls short because insufficient feature patterns are extracted for classifier training. The proposed approach consists of preprocessing, normalization and training the model. For training the model the proposed approach uses GA-TCN.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 7-12
Technological Evaluation and Software Bug Training using Genetic Algorithm and Time Convolution Neural Network (GA-TCN)
One crucial step in addressing bugs is assigning a proper severity rating to each report. New bugs are being reported at such a high rate that the bug repository has grown significantly in size. The bug triaging procedure has become more subjective as the size of the bug repository has grown. Therefore, the bug triaging procedure requires a classification of the severity of a problem report. Several machine learning approaches to automatically rank bugs by severity have been proposed. These system performance falls short because insufficient feature patterns are extracted for classifier training. The proposed approach consists of preprocessing, normalization and training the model. For training the model the proposed approach uses GA-TCN.