Ray Donald Dewald
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ray Donald Dewald has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- René Winter
Institute of Aeroelasticity
3 shared publications - Sebastian Florens Zettel
Institute of Aeroelasticity
2 shared publications - Christian Hesse
German Aerospace Center (DLR), Institute of System Architectures in Aeronautics, Hamburg, Germany
1 shared publication - Marc Böswald
Deutsches Zentrum f. Luft- und Raumfahrt
1 shared publication - Marco Norambuena
Institute of Aeroelasticity
1 shared publication René Winter
German Aerospace Center (DLR), Institute of Aeroelasticity
1 shared publication
Latest Publications
- Open Access
- 10 December 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (3) , 1381-1394
Jet engine vibration model for estimating pylon–wing interface loads for realistic structural excitation
The noise passengers experience in aircraft cabins originates from different sources. One of them is structure-borne noise originating from jet engines. In the case of wing-mounted engines, minor imbalances of rotating engine components can result in a vibration of the wing structure. The wing vibrations are transmitted to the fuselage, potentially giving rise to substantial structure-borne noise. While there are state-of-the-art methods for calculating the acoustic emissions of jet engines during relevant flight conditions, i.e., take-off, cruise and landing, this is not the case for operational vibrations of jet engines. This publication focuses on the development of an engine vibration model on the basis of limited data in the early design phase. The result of the vibration model is a vibration load profile that can be used to excite numerical aircraft models. In combination with the respective jet and fan noise excitation profiles acting on the fuselage, this model will enable future studies to perform holistic assessments of the noise acting inside the cabin. The developed model combines a theoretical approach for the estimation of unbalance forces with measurement data from in-flight experiments with a research aircraft. An exemplary vibration load set for a V2500 engine is calculated and applied to a full aircraft model to show the fuselage response.
- 10 December 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (3) , 1381-1394
Open AccessJet engine vibration model for estimating pylon–wing interface loads for realistic structural excitation
The noise passengers experience in aircraft cabins originates from different sources. One of them is structure-borne noise originating from jet engines. In the case of wing-mounted engines, minor imbalances of rotating engine components can result in a vibration of the wing structure. The wing vibrations are transmitted to the fuselage, potentially giving rise to substantial structure-borne noise. While there are state-of-the-art methods for calculating the acoustic emissions of jet engines during relevant flight conditions, i.e., take-off, cruise and landing, this is not the case for operational vibrations of jet engines. This publication focuses on the development of an engine vibration model on the basis of limited data in the early design phase. The result of the vibration model is a vibration load profile that can be used to excite numerical aircraft models. In combination with the respective jet and fan noise excitation profiles acting on the fuselage, this model will enable future studies to perform holistic assessments of the noise acting inside the cabin. The developed model combines a theoretical approach for the estimation of unbalance forces with measurement data from in-flight experiments with a research aircraft. An exemplary vibration load set for a V2500 engine is calculated and applied to a full aircraft model to show the fuselage response.
- Open Access
- 22 August 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (2) , 829-839
Parametric approach to primary structure modeling of aircraft for cabin noise analysis in FEM
The goals of the European Green Deal require the development of low-emission aircraft propulsion systems that consider sustainable fuels. However, there is a conflict of objectives between effective fuel reduction and noise development of the propulsion system, as particularly efficient propulsion concepts are often based on open rotors, which usually cause increased exterior and interior noise. As a result, precise vibroacoustic models are essential in the early design phase to evaluate and mitigate cabin noise. However, many essential details required for accurate cabin noise prediction are not yet fully defined during preliminary aircraft design. Consequently, the simulation chain consisting of the excitation, primary structure, secondary structure and cavity contains numerous assumptions. To address this challenge, this publication focuses on the parametric creation of full primary structure models based on preliminary design data, with a level of detail relevant for the vibroacoustic frequency range. A central contribution of this work is the derivation of generic modeling guidelines, such as wave-resolving element discretization in the circumferential direction and longitudinal direction of the fuselage structure as well as parameterization of rivet stiffness, from high-resolution experimental vibration data from the research platform Acoustic Flight-Lab. These guidelines are applicable to other fuselage configurations and aim to improve the accuracy of automated FE models. In addition to model creation, this publication proposes an approach for early vibroacoustic assessment at the primary structure level, utilizing spatially and spectrally integrated energy distributions. The applicability of this approach is demonstrated on two different aircraft configurations using realistic operating excitations of V2500 engines in cruise flight.
- 22 August 2025
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 17 (2) , 829-839
Open AccessParametric approach to primary structure modeling of aircraft for cabin noise analysis in FEM
The goals of the European Green Deal require the development of low-emission aircraft propulsion systems that consider sustainable fuels. However, there is a conflict of objectives between effective fuel reduction and noise development of the propulsion system, as particularly efficient propulsion concepts are often based on open rotors, which usually cause increased exterior and interior noise. As a result, precise vibroacoustic models are essential in the early design phase to evaluate and mitigate cabin noise. However, many essential details required for accurate cabin noise prediction are not yet fully defined during preliminary aircraft design. Consequently, the simulation chain consisting of the excitation, primary structure, secondary structure and cavity contains numerous assumptions. To address this challenge, this publication focuses on the parametric creation of full primary structure models based on preliminary design data, with a level of detail relevant for the vibroacoustic frequency range. A central contribution of this work is the derivation of generic modeling guidelines, such as wave-resolving element discretization in the circumferential direction and longitudinal direction of the fuselage structure as well as parameterization of rivet stiffness, from high-resolution experimental vibration data from the research platform Acoustic Flight-Lab. These guidelines are applicable to other fuselage configurations and aim to improve the accuracy of automated FE models. In addition to model creation, this publication proposes an approach for early vibroacoustic assessment at the primary structure level, utilizing spatially and spectrally integrated energy distributions. The applicability of this approach is demonstrated on two different aircraft configurations using realistic operating excitations of V2500 engines in cruise flight.
- Open Access
- 25 April 2025
- Published by Springer Nature in Research Square
Parametric approach to primary structure modelling of aircrafts for cabin noise analysis in FEM
The goals of the European Green Deal require the development of low-emission aircraft propulsion systems that take sustainable fuels into account. However, there is a conflict of objectives between effective fuel reduction and noise development of the propulsion system, as particularly efficient propulsion concepts are often based on open rotors which usually cause increased exterior and interior noise. In this context, the creation of precise vibroacoustic models is becoming increasingly important in order to ensure a valid evaluation and optimization of aircraft interior acoustics in the early phases of the design process. The primary structure of the entire aircraft is an important component of the transfer path between external excitation and the resulting cabin noise, because it is decisive for the spatial propagation of structure-borne noise. This publication therefore focuses on the parametric creation of complete primary structure models for aircrafts based on preliminary design data with a level of detail that is relevant for the vibroacoustic frequency range. Generally valid modeling approaches for finite element models, e.g. the correct choice of mesh resolution, that were derived from experiments are also shown in detail. In combination with the external excitation, qualitative statements on the vibroacoustic properties of the aircraft can already be made at primary structure level, by calculating spatially and spectrally integrated energy distributions. This is demonstrated for two different aircraft configurations using validated operating excitations of V2500 engines in cruise flight.
- 25 April 2025
- Published by Springer Nature in Research Square
Open AccessParametric approach to primary structure modelling of aircrafts for cabin noise analysis in FEM
The goals of the European Green Deal require the development of low-emission aircraft propulsion systems that take sustainable fuels into account. However, there is a conflict of objectives between effective fuel reduction and noise development of the propulsion system, as particularly efficient propulsion concepts are often based on open rotors which usually cause increased exterior and interior noise. In this context, the creation of precise vibroacoustic models is becoming increasingly important in order to ensure a valid evaluation and optimization of aircraft interior acoustics in the early phases of the design process. The primary structure of the entire aircraft is an important component of the transfer path between external excitation and the resulting cabin noise, because it is decisive for the spatial propagation of structure-borne noise. This publication therefore focuses on the parametric creation of complete primary structure models for aircrafts based on preliminary design data with a level of detail that is relevant for the vibroacoustic frequency range. Generally valid modeling approaches for finite element models, e.g. the correct choice of mesh resolution, that were derived from experiments are also shown in detail. In combination with the external excitation, qualitative statements on the vibroacoustic properties of the aircraft can already be made at primary structure level, by calculating spatially and spectrally integrated energy distributions. This is demonstrated for two different aircraft configurations using validated operating excitations of V2500 engines in cruise flight.