FSFabian Scheckenbach

Fabian Scheckenbach

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Fabian Scheckenbach has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Beyond the bilayer: multilayered hygroscopic actuation in pine cone scales

    by Kim Ulrich, Max David Mylo, Tom Masselter, Fabian Scheckenbach, Sophia Fischerbauer, Martin Nopens, Silja Flenner, Imke Greving, Linnea Hesse, Thomas Speck

    The anisotropic hygroscopic behavior of pine cone scales and its effect on bending motion, with implications for bioinspired actuation, is investigated. Using gravimetric water uptake measurements, synchrotron radiation-based nano-holotomography, and digital volume correlation analysis, inter- and intra-tissue variations of hygroscopic swelling/shrinkage were observed. In addition, the moisture content of pine cone scale tissues was measured as a function of relative humidity. There were distinct differences between tissues and a pronounced hysteresis between sorption and desorption. Finite element analysis was performed on geometries ranging from simplified bilayer models to complex remodeled scales. Simulation results showed an underestimation of the bending of bilayer geometries due to an overestimated contribution of sclerenchyma fiber stiffness. Geometries with discrete fibers embedded in a brown tissue matrix more accurately reproduced the bending angles observed in experiments. This highlights the importance of the chosen material properties and tissue arrangements for predicting pine cone scale bending in silico. By contributing to a deeper understanding of pine cone scale biomechanics, these results also support the development of bioinspired technical applications. Future studies should refine tissue mechanical properties and integrate high-resolution computed tomography-based geometries to further elucidate the mechanisms underlying hygroscopic actuation. This integrative approach will bridge experimental findings with computational modeling and advance plant biomechanics and biomimetic transfer.


  • Open Access

    Design and implementation of a climate chamber for moisture sensitive nanotomography of biological samples

    by Martin Nopens, Imke Greving, Silja Flenner, Linnea Hesse, Jan Lüdtke, Michael Altgen, Gerald Koch, Johannes Beruda, Sabrina Heldner, Hannes Köhm, et al.

    Deep understanding of the structural composition and growth of biological specimens is becoming increasingly important for the development of bio-based and sustainable material systems. Full-field nano-computed tomography is particularly suitable for this purpose as it allows for non-destructive 3D imaging at high spatial resolution. However, most biological samples are functionalized by water and respond sensitively to any changes in climate conditions, specifically relative humidity, by adjusting their material moisture content. To date, only a limited number of tomography instruments offer an in situ climate control option to users. These, however, are limited either by the range of relative humidity states, the long times required to change the climate state, or obstruction or attenuation of the beam. Here, the first fully automatized climate cell for in situ full-field nanotomography is presented. It has been designed, built and integrated at the nanotomography station at the P05 imaging beamline, operated by Hereon at the DESY storage ring PETRA III, Germany. The highly flexible and windowless design allows the humidity dependent swelling and shrinking of lignified plant cell walls to be studied in situ , using phase contrast nanotomography. The concept of this climate chamber can easily be integrated into other setups. It operates in the relative humidity range of 0–90% and can be controlled in a temperature range of 10–50°C. Climate conditions can be adjusted at any time, remotely from the control hutch by using a humidity generator. Results show that the developed setup maintains a stable climate during the entire duration of a tomographic scan at different humidities and does not obstruct the sample or hinder the imaging conditions. During the tomographic investigation the sample remains stable in the flow of the air stream and shows typical cell wall swelling and shrinking behaviour depending on the equilibrium moisture content. This new climate cell is now available to all users of the P05 nanotomography instrument for conditioning samples, serving a wide range of scientific applications.


  • A 3D-Printed Thermoresponsive Artificial Venus Flytrap Lobe Based on a Multilayer of Shape Memory Polymers

    by Falk J. Tauber, Fabian Scheckenbach, Mario Walter, Thorsten Pretsch, Thomas Speck