Ruitong Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ruitong Zhang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Mingyue Qiu
School of Transportation and Civi Engineering, Nantong University, Nantong 226019, China
3 shared publications - Shuyang Yu
School of Transportation and Civil Engineering, Nantong University, Nantong 226019, China
3 shared publications - Yifei Li
Department of Mechanical Engineering, Huzhou University, Huzhou 313002, China
2 shared publications - Cheng Chen
College of Mechanics and Engineering Science, Hohai University, Nanjing 211100, China
1 shared publication - Chuan Zhao
Sichuan Academy of Water Conservancy, Chengdu 610072, China
1 shared publication - Fanbao Meng
College of Energy Storage Technology, Shandong University of Science and Technology, Qingdao 266590, China
1 shared publication
Latest Publications
- Open Access
Investigating the Cracking Processes and Bearing Performance of Fissured Concrete SCB Specimens via DEM-Based Mesoscopic Modeling Considering Fissure Angle, Aggregate Content and Porosity
To reveal the mesoscopic fracture mechanism of fissured concrete, this study employed the discrete element method (DEM) and adopted the parallel bond model (PBM) within the two-dimensional particle flow code (PFC2D) to construct a mesoscopic model of concrete semi-circular bending (SCB) specimens with prefabricated fissures. Three sets of schemes were designed by varying prefabricated fissure angles (0–45°), aggregate contents (30–45%), and porosities (3–6%), and numerical simulations of three-point bending loads were conducted to explore the effects of each parameter on the crack propagation law and load-bearing performance of the specimens. Validation was performed by comparing the simulated load–displacement curves with the typical quasi-brittle mechanical characteristics of concrete (exhibiting “linear elastic rise–pre-peak stress fluctuation–nonlinear decline”) and verifying that the DEM could accurately capture the entire process from microcrack initiation at the aggregate–mortar interface, crack deflection/bifurcation induced by pores, to macroscopic fracture penetration—consistent with the known mesoscopic damage evolution law of concrete. The results indicate that the crack propagation mode evolves from straight extension to tortuous branching as parameters change. Moreover, the peak strength first increases and then decreases with the increase in each parameter: when the fissure angle is 15°, the aggregate content is 35%, and the porosity is 4%, the specimens achieve an optimal balance between crack propagation resistance and energy dissipation, resulting in the best load-bearing performance. Specifically, the prefabricated fissure angle dominates the stress type (tension–shear transition); aggregates regulate crack resistance through a “blocking–diverting” effect; and pores, acting as defects, influence stress concentration. This study verifies the reliability of DEM in simulating concrete fracture behavior, enriches the mesoscopic fracture theory of concrete, and provides reliable references for the optimization of concrete material proportioning (e.g., aggregate–porosity ratio adjustment) and anti-cracking design of infrastructure (e.g., pavement, tunnel linings) in engineering practices.
Open AccessInvestigating the Cracking Processes and Bearing Performance of Fissured Concrete SCB Specimens via DEM-Based Mesoscopic Modeling Considering Fissure Angle, Aggregate Content and Porosity
To reveal the mesoscopic fracture mechanism of fissured concrete, this study employed the discrete element method (DEM) and adopted the parallel bond model (PBM) within the two-dimensional particle flow code (PFC2D) to construct a mesoscopic model of concrete semi-circular bending (SCB) specimens with prefabricated fissures. Three sets of schemes were designed by varying prefabricated fissure angles (0–45°), aggregate contents (30–45%), and porosities (3–6%), and numerical simulations of three-point bending loads were conducted to explore the effects of each parameter on the crack propagation law and load-bearing performance of the specimens. Validation was performed by comparing the simulated load–displacement curves with the typical quasi-brittle mechanical characteristics of concrete (exhibiting “linear elastic rise–pre-peak stress fluctuation–nonlinear decline”) and verifying that the DEM could accurately capture the entire process from microcrack initiation at the aggregate–mortar interface, crack deflection/bifurcation induced by pores, to macroscopic fracture penetration—consistent with the known mesoscopic damage evolution law of concrete. The results indicate that the crack propagation mode evolves from straight extension to tortuous branching as parameters change. Moreover, the peak strength first increases and then decreases with the increase in each parameter: when the fissure angle is 15°, the aggregate content is 35%, and the porosity is 4%, the specimens achieve an optimal balance between crack propagation resistance and energy dissipation, resulting in the best load-bearing performance. Specifically, the prefabricated fissure angle dominates the stress type (tension–shear transition); aggregates regulate crack resistance through a “blocking–diverting” effect; and pores, acting as defects, influence stress concentration. This study verifies the reliability of DEM in simulating concrete fracture behavior, enriches the mesoscopic fracture theory of concrete, and provides reliable references for the optimization of concrete material proportioning (e.g., aggregate–porosity ratio adjustment) and anti-cracking design of infrastructure (e.g., pavement, tunnel linings) in engineering practices.
- Open Access
Numerical Simulation of Tunnel Boring Machine (TBM) Disc Cutter Rock Breaking Based on Discrete Element Method
To address the issue that the current research on TBM disc cutter rock breaking insufficiently considers actual stratified rock masses, this study constructs numerical models of stratified rock masses with different bedding dip angles and bedding spacings based on the discrete element method (DEM). The whole process of TBM disc cutter rock breaking is numerically simulated through the displacement loading mode. The research results show that the bedding dip angle has a significant impact on the crack propagation mode. When α = 45°, the bedding intersects with the contact point of the disc cutter, and cracks penetrate directly along the bedding without an obvious “crushed zone”, resulting in the minimum number of cracks. The bedding spacing regulates the rock-breaking effect in stages. When d = 45°, the “crushed zone” interacts with two beddings to form three branch cracks, reaching the peak number of cracks and achieving the optimal rock-breaking efficiency. The cracks generated by disc cutter rock breaking exhibit the characteristic of “slow initial growth and rapid later surge” with the increase in time steps, which is highly consistent with the actual mechanical process of rock breaking. This study reveals the influence mechanism of bedding properties on TBM disc cutter rock breaking, verifies the reliability of the DEM combined with PB and SJ models in the simulation of stratified rock mass breaking, and provides theoretical support and data references for the parameter optimization of TBM disc cutters and efficient tunneling under complex stratified geological conditions.
Open AccessNumerical Simulation of Tunnel Boring Machine (TBM) Disc Cutter Rock Breaking Based on Discrete Element Method
To address the issue that the current research on TBM disc cutter rock breaking insufficiently considers actual stratified rock masses, this study constructs numerical models of stratified rock masses with different bedding dip angles and bedding spacings based on the discrete element method (DEM). The whole process of TBM disc cutter rock breaking is numerically simulated through the displacement loading mode. The research results show that the bedding dip angle has a significant impact on the crack propagation mode. When α = 45°, the bedding intersects with the contact point of the disc cutter, and cracks penetrate directly along the bedding without an obvious “crushed zone”, resulting in the minimum number of cracks. The bedding spacing regulates the rock-breaking effect in stages. When d = 45°, the “crushed zone” interacts with two beddings to form three branch cracks, reaching the peak number of cracks and achieving the optimal rock-breaking efficiency. The cracks generated by disc cutter rock breaking exhibit the characteristic of “slow initial growth and rapid later surge” with the increase in time steps, which is highly consistent with the actual mechanical process of rock breaking. This study reveals the influence mechanism of bedding properties on TBM disc cutter rock breaking, verifies the reliability of the DEM combined with PB and SJ models in the simulation of stratified rock mass breaking, and provides theoretical support and data references for the parameter optimization of TBM disc cutters and efficient tunneling under complex stratified geological conditions.
- Open Access
Failure Mechanisms of Basalt Fiber Concrete Under Splitting Tensile Tests and DEM Simulations
To address the cracking problem caused by the weak tensile performance of concrete, this study investigates the failure mechanisms of basalt fiber-reinforced concrete under different fiber contents, single-blend, and mixed-blend schemes through splitting tensile tests and discrete element method (DEM) simulations. The tests employ 0.1–0.3% of 18 mm single-blend fibers and 6 mm:12 mm:18 mm (3:4:3) mixed-blend schemes, and PFC software is used to simulate crack propagation in fiber-reinforced concrete. The results show that the optimal 0.2% content of 18 mm single-blend fibers enhances the splitting tensile strength by 10.8%, whereas excessive 0.3% content reduces the strength by 7.8% due to poor dispersion. The mixed-blend scheme, via gradient crack-resisting effects of multi-scale fibers, increases the strength by 7.43% compared with the single-blend group at the same fiber content. DEM simulations reveal that fibers delay crack propagation through stress concentration transfer: single-blend fibers render tortuous crack paths, while mixed-blend fibers form three-dimensional crack networks, transforming the failure energy dissipation mode from single pull-out to multi-stage consumption. This research provides theoretical basis and optimization strategies for the anti-cracking design of basalt fiber-reinforced concrete.
Open AccessFailure Mechanisms of Basalt Fiber Concrete Under Splitting Tensile Tests and DEM Simulations
To address the cracking problem caused by the weak tensile performance of concrete, this study investigates the failure mechanisms of basalt fiber-reinforced concrete under different fiber contents, single-blend, and mixed-blend schemes through splitting tensile tests and discrete element method (DEM) simulations. The tests employ 0.1–0.3% of 18 mm single-blend fibers and 6 mm:12 mm:18 mm (3:4:3) mixed-blend schemes, and PFC software is used to simulate crack propagation in fiber-reinforced concrete. The results show that the optimal 0.2% content of 18 mm single-blend fibers enhances the splitting tensile strength by 10.8%, whereas excessive 0.3% content reduces the strength by 7.8% due to poor dispersion. The mixed-blend scheme, via gradient crack-resisting effects of multi-scale fibers, increases the strength by 7.43% compared with the single-blend group at the same fiber content. DEM simulations reveal that fibers delay crack propagation through stress concentration transfer: single-blend fibers render tortuous crack paths, while mixed-blend fibers form three-dimensional crack networks, transforming the failure energy dissipation mode from single pull-out to multi-stage consumption. This research provides theoretical basis and optimization strategies for the anti-cracking design of basalt fiber-reinforced concrete.