Christian Auguste Harris
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Christian Auguste Harris has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
Albuquerque Sandia National Laboratories (Snl-Nm)
6 shared publicationsUsdoe National Nuclear Security Administration (Nnsa)
5 shared publicationsAlejandro Hinojos
Sandia National Laboratories (SNL-CA), Livermore, CA (United States)
2 shared publicationsCatherine Elizabeth Sobczak
Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)
2 shared publications- David P. Adams
Sandia National Laboratories 1 , Albuquerque, New Mexico 87185
2 shared publications - Erin Barrick
Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)
2 shared publications
Latest Publications
- Open Access
- 11 August 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Sb2O3 Content on the Friction and Wear Behavior of MoS2-Sb2O3 Nanocomposite Films
MoS2-Sb2O3 nanocomposite coatings are widely used as aerospace dry film lubricants, yet the composition-dependent crystallinity, hardness, friction, and wear remain largely unexplored. Here, co-sputtered MoS2-Sb2O3 films with Sb contents from pure MoS2 to 31.0 at.% were evaluated using wavelength dispersive spectroscopy, X-ray diffraction, nanoindentation, and reciprocating tribological testing in dry N2 and humid air. Increasing Sb2O3 content progressively suppressed crystallinity, with films becoming largely amorphous above 7.5 at.% Sb. At the apparent amorphization threshold, hardness peaked at 6.77 GPa, an 87% increase compared to pure nanocrystalline MoS2. Upon further addition of Sb2O3, hardness was reduced proportionally to composition, decreasing to 4.01 GPa at 31.0 at.% Sb. These results revealed an important threshold concentration of approximately 7.5 at.% Sb, beyond which additional Sb2O3 no longer provides further hardness improvement. Tribological performance (i.e., friction and wear) depended strongly on both composition and environment. Films with 4.8 at.% Sb exhibited nearly environmentally insensitive initial friction, but these low-Sb compositions also showed elevated steady-state friction and wear rates in dry and low-humidity conditions. In contrast, films containing 9.8–19.2 at.% Sb provided the best combination of initial friction, steady-state friction, and wear resistance across all environments, reducing wear rates by roughly an order of magnitude relative to pure MoS2. Excessive Sb2O3 content, particularly above 27.2 at.% Sb, produced high initial friction and premature failure, possibly due to MoS2 depletion at the sliding interface. These findings identify distinct structural and tribological composition thresholds in MoS2-Sb2O3 nanocomposites and demonstrate the need to tailor Sb2O3 content to the intended operating environment.
- 11 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Sb2O3 Content on the Friction and Wear Behavior of MoS2-Sb2O3 Nanocomposite Films
MoS2-Sb2O3 nanocomposite coatings are widely used as aerospace dry film lubricants, yet the composition-dependent crystallinity, hardness, friction, and wear remain largely unexplored. Here, co-sputtered MoS2-Sb2O3 films with Sb contents from pure MoS2 to 31.0 at.% were evaluated using wavelength dispersive spectroscopy, X-ray diffraction, nanoindentation, and reciprocating tribological testing in dry N2 and humid air. Increasing Sb2O3 content progressively suppressed crystallinity, with films becoming largely amorphous above 7.5 at.% Sb. At the apparent amorphization threshold, hardness peaked at 6.77 GPa, an 87% increase compared to pure nanocrystalline MoS2. Upon further addition of Sb2O3, hardness was reduced proportionally to composition, decreasing to 4.01 GPa at 31.0 at.% Sb. These results revealed an important threshold concentration of approximately 7.5 at.% Sb, beyond which additional Sb2O3 no longer provides further hardness improvement. Tribological performance (i.e., friction and wear) depended strongly on both composition and environment. Films with 4.8 at.% Sb exhibited nearly environmentally insensitive initial friction, but these low-Sb compositions also showed elevated steady-state friction and wear rates in dry and low-humidity conditions. In contrast, films containing 9.8–19.2 at.% Sb provided the best combination of initial friction, steady-state friction, and wear resistance across all environments, reducing wear rates by roughly an order of magnitude relative to pure MoS2. Excessive Sb2O3 content, particularly above 27.2 at.% Sb, produced high initial friction and premature failure, possibly due to MoS2 depletion at the sliding interface. These findings identify distinct structural and tribological composition thresholds in MoS2-Sb2O3 nanocomposites and demonstrate the need to tailor Sb2O3 content to the intended operating environment.
- Open Access
- 1 September 2025
- Published by Office of Scientific and Technical Information (OSTI)
Stoichiometric determination in thin films: a study of BaTiO3
- 1 September 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessStoichiometric determination in thin films: a study of BaTiO3
- Open Access
- 1 May 2025
- Published by Office of Scientific and Technical Information (OSTI)
XRD and STEM Analysis of Structural Variation in Nanocrystalline Cu-Ag Thin Films
- 1 May 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessXRD and STEM Analysis of Structural Variation in Nanocrystalline Cu-Ag Thin Films
- Open Access
- 1 November 2024
- Published by Office of Scientific and Technical Information (OSTI)
Analysis of Cu-Ag and Ni-Pt High Throughput Survey Results
- 1 November 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAnalysis of Cu-Ag and Ni-Pt High Throughput Survey Results
- Open Access
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
The effect of laser remelting on the microstructure and chemistry of additively manufactured MoNbTaTi RHEA
- 1 October 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessThe effect of laser remelting on the microstructure and chemistry of additively manufactured MoNbTaTi RHEA
- Open Access
- 1 May 2024
- Published by Office of Scientific and Technical Information (OSTI)
Gasb-to-Si Direct Wafer Bonding and Thermal Budget Considerations for Photonic Applications
- 1 May 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessGasb-to-Si Direct Wafer Bonding and Thermal Budget Considerations for Photonic Applications