YLYun Hyeok Lee

Yun Hyeok Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yun Hyeok Lee has a total of 60 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Molecular-scale tough adhesives based on the Lake–Thomas model

    by Jeong-Yun Sun, Yuseon Heo, Hakjun Lee, Chang Seo Park, Jinwoo Park, Seunghyun Sun, Sunbo Kang, Gimin Sung, Yun Hyeok Lee, Byoung Soo Kim, et al.

    High interfacial fracture resistance commonly relies on finite-thickness adhesive layers that dissipate energy through deformation, whereas molecularly thin interfaces provide little volume for such toughening. Here, we report a molecular-scale bonding strategy connecting opposing surfaces through covalently interlinked molecular bridges whose load-bearing backbone length is systematically controlled. Guided by the Lake–Thomas framework, we show that bridge backbone length controls interfacial fracture resistance through the fracture work of individual load-bearing connections. The optimized system reaches an interfacial fracture energy of approximately 500 J m⁻² with a sub-5-nm interphase for polyimide–polyimide bonding. Surface analysis and molecular-dynamics simulations support the primary role of backbone length while suggesting that surface-tethered chain organization modulates length-dependent toughening through bridge density. The strategy strengthens dissimilar interfaces and maintains interfacial reliability under environmental exposure. These results establish backbone length as a design parameter for tough molecularly thin interfaces, providing a route to mechanically robust heterogeneous integration.

  • Boosting ionic conductivity of single-ion conductive polyelectrolyte elastomers via high-dielectric plasticizers

    by Sangjun Ma, Solji Ahn, Jae-Man Park, Hakjun Lee, Seong-Yu Choi, Yong Eun Cho, Dong-Yup Lee, Seung-Woo Lee, Maga Kim, Seung Won Moon, et al.

    Ionic conduction plays a vital role in biological systems, energy storage and ionotronic devices. Polyelectrolyte elastomers have attracted growing interest as solid-state single-ion conductors due to their inherent ion selectivity, leakage-free nature and mechanical elasticity. However, existing polyelectrolyte elastomers have relatively low ionic conductivity (~10-3 mS cm-1), limiting their applicability as efficient ionic conductors. Here we present a materials design approach that boosts conductivity and preserves leakage-free operation by introducing a solid-state additive that combines two key characteristics: a high dielectric constant to increase dissociated ion density ( n ) and a plasticizing effect to enhance ion mobility ( μ ). Demonstrated with succinonitrile, this approach increases conductivity by over two orders of magnitude at room temperature across both polycationic and polyanionic systems, further enhancing elasticity. By elevating conductivity across diverse polyelectrolyte networks, this work demonstrates a versatile route to achieve stable and efficient ion transport for next-generation solid-state single-ion conductors.


  • Open Access

    A reconfigurable dielectric elastomer actuator via phase-transitional ferrofluid enables sustainable operation

    by Yun Hyeok Lee, Seung Won Moon, Min-Gyu Lee, Won Jun Song, Seong-Yu Choi, Gimin Sung, Yong Eun Cho, Junhyun Choi, Byung Ik Park, Younghoon Lee, et al.

    Dielectric elastomer actuators (DEAs) are promising soft transducers capable of rapid and precise actuation. However, their conventional architecture for efficient actuation confines DEAs in predesigned operational modes, leading to limited applications. Here, we introduce a reconfigurable DEA system using phase-transitional ferrofluid (PTF) electrodes. PTF switches its states between solid and liquid, satisfying requirements for a reconfigurable electrode for DEAs. In the sol state, the stable and high magnetic responsiveness inspired by ferrofluid and the low viscosity achieved through plasticization collectively enable dynamic reconfiguration of the electrode. In the gel state, PTF ensures stable shape retention and exhibits reduced interfacial slip during DEA actuation. This reconfigurable nature greatly increases adaptability and ensures continuous operation even when electrodes undergo disconnection or dielectric failure. Moreover, the PTF electrodes can be retrieved and reused after actuation, demonstrating their excellent recyclability. The combination of mechanical compliance, magnetic reconfigurability, and material sustainability renders the PTF a versatile electrode strategy for next-generation reconfigurable electroactive systems.


  • Open Access

    Elasto-magnetic instabilities for amplified actuation and mechanical memory

    by Seong-Yu Choi, Ji-Sung Park, Won Jun Song, Maga Kim, Yun Hyeok Lee, Yong Eun Cho, Hakjun Lee, Ho-Young Kim, Jeong-Yun Sun

    Instabilities can generate fast and amplified motion in mechanical systems. Here, we present an elasto-magnetic instability that combines magnetic attraction and elastic tension to create bistable dynamics. To demonstrate this, we built a coupled elasto-magnetic vibration system that produces amplified motion and greater displacement and force than a control system across a wide frequency range. We also establish design principles that can be applied to different configurations by studying the balance between magnetic and elastic forces. The system also shows inertial hysteresis, which enables mechanical memory by storing external inputs in volatile and non-volatile modes with adjustable thresholds. This dual function of amplification and memory shows how instabilities can be potentially used for programmable and adaptive soft actuation.

  • In Situ Grown Metal–Organic Frameworks with Diverse Ligands on Nanofibrous Sheet for Modulating Triboelectric Performance

    by Cho Rim Kim, Jae Hoon Han, Myoung Ju Kim, Dabin Lee, Nayoung Shin, Se-Na Kim, Han Bi Ji, Chang Hee Min, Yun Hyeok Lee, Jeong-Yun Sun, et al.

    In this study, we developed a triboelectric material by growing metal-organic frameworks (MOFs) in situ on electrospun polyvinylidene fluoride-trifluoroethylene (PVDF-TrFE) nanofiber sheets. By varying the ligand chemistry, using electron-donating (-NH2) or electron-withdrawing (-COOH, -NO2) groups, we modulated the triboelectric properties without altering the nanofiber morphology or β-phase crystallinity. Structural and surface characterizations confirmed in situ grown MOF integration and ligand-dependent modulation of surface properties. When applied to triboelectric nanogenerators (TENGs), the materials exhibited output responses modulated by ligand type, with the NO2-functionalized MOF achieving the highest increase, producing a maximum peak-to-peak voltage of approximately 130 V that remained stable over 30,000 contact-separation cycles. These findings demonstrate a reliable, ligand-tunable strategy for controlling interfacial properties, emphasizing the dominant role of surface electronic characteristics in determining triboelectric performance.


  • Open Access

    Dynamically assembled magnetic nanoparticles in a phase transitional matrix for reconfigurable electronics

    by Min-Gyu Lee, Seong-Yu Choi, HyunJae Yoo, Jae-Man Park, Younghoon Lee, Yun Hyeok Lee, Yong Eun Cho, Sungsoo Lim, Hakjun Lee, Jeong-Yun Sun

    The structure of an electronic device is predetermined at its birth, necessitating new designs and fabrication processes for alternative functions. The advent of reconfigurable electronics, modifying its circuits after manufacture, has unlocked the potential for devices to perform adaptive roles as needed. However, the trade-off between the degree of freedom to reform its structure and electrical stability restricts its potential roles, diminishing the system’s significance. Here, we present a reconfigurable assembly of magnetic nanoparticles in a phase transitional matrix (RAMP) system capable of seamlessly transforming their structure with robust electrical junctions. Nanoparticles form conductive percolation under a precisely patterned magnetic field. Within a phase transitional matrix, junctions between nanoparticles are tightened, enhancing electrical performance during transitions. We demonstrated in situ electrical switching and high-resolution alternating current electroluminescence display using the RAMP system. With enhanced reconfigurability and electrical reliability, we anticipate that the RAMP system will suggest a previously unexplored approach to on-demand electronics.


  • Open Access

    All‐3D‐Printed Multi‐Environment Modular Microrobots Powered by Large‐Displacement Dielectric Elastomer Microactuators

    by Won Jun Song, Yong‐Woo Kang, Yun Hyeok Lee, Junhyung Kim, Bastien F.G. Aymon, Seong‐Yu Choi, Yong Eun Cho, Xiao‐Yun Yan, Shucong Li, Younghoon Lee, et al.

    Microrobots are expected to push the boundaries of robotics by enabling navigation in confined and cluttered environments due to their sub‐centimeter scale. However, most microrobots perform best only in the specific conditions for which they are designed and require complete redesign and fabrication to adapt to new tasks and environments. Here, fully 3D‐printed modular microrobots capable of performing a broad range of tasks across diverse environments are introduced. For multi‐environment navigation, large‐displacement dielectric elastomer microactuators with a soft‐stiff hybrid structure are developed, capable of powering microrobots to stride over obstacles on various terrestrial terrain and rapidly propel themselves across aquatic terrain. To further expand their capabilities beyond mere navigation, ten task‐specific modules for the microrobots are developed. All modules are fabricated using a digital light processing multimaterial 3D printer capable of simultaneously printing multiple photocurable resins, providing a broadly applicable platform for fabricating mesoscale robotic components. The microrobots navigate across smooth, rough, granular, and aquatic environments, demonstrating tasks such as controlling the movements of nearby robots, interacting with humans to avoid collisions, and collaboratively dragging heavy objects through multi‐unit operation. The study addresses key limitations hindering the integration of modular design into microrobots, enabling adaptation to new environments and tasks.


  • Top Cited Papers
    Open Access

    Gel-Based Ionic Circuits

    by Hyunjae Yoo, Yun Hyeok Lee, Min-Gyu Lee, Jeong-Yun Sun

    Ionic circuits have emerged as a promising candidate to bridge the gap between biological and artificial systems by applying the mechanically compliant and adaptive nature of gels as ionic conductors. Gel-based ionic circuits exploit the intrinsic characteristics of ions, such as their mass, diversity, and local accumulation, to achieve selectivity, hysteresis, and chemical-electric signal transduction. Their dynamic and nonlinear behaviors not only emulate traditional solid-state electronic systems but also exhibit unique functionalities and operating mechanisms extending beyond established electronic paradigms. In this review, we categorize gel-based ionic circuits into four major functional classes: passive circuit elements, active circuit elements, power sources, and noncircuit elements. We comprehensively discuss the fundamental operating principles, materials strategies, and current challenges, eventually highlighting opportunities for future advancement in ionic devices.


  • Open Access

    Enzyme‐Regulated Extended Swelling of Hydrogels for Dehiscence‐Less Tissue Expansions

    by Byung Ik Park, Dong‐Yup Lee, Sungsoo Lim, JangHyuk Kim, Min‐Gyu Lee, Chang Seo Park, Hyeonuk Na, Yong Eun Cho, Yun Hyeok Lee, Junsang Doh, et al.

    Tissue expansion is traditionally achieved by injecting saline into an implanted silicone balloon via external tubing, which causes patient discomfort. Hydrogels eliminate the need for tubing due to their self‐swelling properties, but they fail to prevent suture wound dehiscence due to immediate swelling after implantation. Here, the concept of “extended swelling” in an interpenetrating hydrogel network is introduced to avoid dehiscence. The hydrogel consists of enzymatically degradable hyaluronic acid (HA) networks and non‐degradable polyacrylic acid (PAAc) networks. The gel remains structurally intact until suture wound healing after implantation by the constraint of the HA networks on the PAAc networks. Upon hyaluronidase (HYAL) injection, the HA networks degrade, initiating the extended swelling after which enzymatic degradation controls its onset and rate. Furthermore, the generalized ideal elastomeric gel model is employed to understand the extended swelling process. The model predicts the maximum extended equilibrium swelling ratio in vivo, confirming the hydrogel's ability to generate sufficient pressure while preventing overexpansion beyond the tissue rupture threshold. The theoretical framework aligns with experimental observations, demonstrating that the tissue expansion is induced by yes1‐associated protein (YAP1)‐mediated epidermal proliferation. This approach establishes its potential as a next‐generation tissue expander for clinical applications.