Sandeep Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sandeep Kumar has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Navjeet Bagga
IIT Bhubaneswar
10 shared publications - Deven H. Patil
School of Electrical and Computer Sciences, Indian Institute of Technology Bhubaneswar, Odisha, India
7 shared publications - Sunil Rathore
Department of ECE, Manipal Academy of Higher Education (MAHE), Manipal Institute of Technology, Manipal, Karnataka, India
7 shared publications S. Dasgupta
Department of Electronics and Communication Engineering, IIT Roorkee, Roorkee, Uttarakhand, India
4 shared publications- Sudeb Dasgupta
IIT Roorkee
4 shared publications - Ankit Dixit
DeepNano Group, James Watt School of Engineering, University of Glasgow, Glasgow, U.K.
3 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 26 (3) , 832-838
Reliability-Assisted Electro-Physical Modeling of Radiation-Induced Resistance Fluctuation in Nanosheet FET
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 26 (3) , 832-838
Reliability-Assisted Electro-Physical Modeling of Radiation-Induced Resistance Fluctuation in Nanosheet FET
- 24 August 2026
- Published by Taylor & Francis
- p. 64-74
Design and performance analysis of thin-film solar cell
The important figure of merit for increasing the solar cell’s conversion efficiency is the enhanced absorption rate. Therefore, in order to witness an increase in the absorption rate, better light-trapping mechanisms such as surface texturing, antireflective coating, or usage of transparent conductive oxides have become dominant among researchers. Hence, in this chapter, a novel attempt has been made to study and analyze the effect of the surface texturing technique on thin-film solar cell technology through comparison between the results obtained with and without the application of the technique. Furthermore, in accordance with the textured tandem thin-film solar cell, the effect of variations in height of triangular textures on the values of critical parameters like J SC , V OC , Fill Factor ( FF ) and efficiency is also analyzed.
- 24 August 2026
- Published by Taylor & Francis
- p. 64-74
Design and performance analysis of thin-film solar cell
The important figure of merit for increasing the solar cell’s conversion efficiency is the enhanced absorption rate. Therefore, in order to witness an increase in the absorption rate, better light-trapping mechanisms such as surface texturing, antireflective coating, or usage of transparent conductive oxides have become dominant among researchers. Hence, in this chapter, a novel attempt has been made to study and analyze the effect of the surface texturing technique on thin-film solar cell technology through comparison between the results obtained with and without the application of the technique. Furthermore, in accordance with the textured tandem thin-film solar cell, the effect of variations in height of triangular textures on the values of critical parameters like J SC , V OC , Fill Factor ( FF ) and efficiency is also analyzed.
- 20 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 2415-2421
Demonstrating the Electro-Thermal Dynamics in Complementary FETs: Quantifying the Role of Self-Heating and Grain Effect Intercoupling
The vertical stacking of sheets and separating them by a dielectric raises severe thermal and geometrical reliability concerns in the complementary field effect transistor (CFET). Using well-calibrated TCAD models, we investigated the impact of the self-heating effect (SHE) and the role of dielectric separation wall (DSW) in electro-thermal coupling. The resulting thermal crosstalk due to DSW shows an increase in temperature of 2.09% (1.60%) at the pFET (nFET) when nFET (pFET) is in the on state. Furthermore, the metal grain granularity (MGG) is a vital factor that affects the electro-thermal characteristics. It offers the randomized metal work function (WF), thereby significantly causing the shift in threshold voltage (Vth). A semi-empirical model is proposed to define the ratio of effective grain size to gate (RGG) area, which provides insight into the grain boundaries and their optimization in CFET. In addition, the significance of the extension region (LEXT) in electro-thermal performance is explored, as LEXT offers series resistance, which modulates thermal resistance. The increase in LEXT from 3 to 7 nm results in decreased lattice temperature (TL) by ~29 K; however, it increases the series resistance and causes the decrease in on current (ION) by 28% (25%) in nFET (pFET). At last, we predicted the device’s lifetime based on Vth shift (i.e., change in V ${}_{\text {th}}= \pm 50$ mV). Thus, the proposed analysis is worth exploring for the reliability-aware CFET design in sub-3 nm nodes.
- 20 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (4) , 2415-2421
Demonstrating the Electro-Thermal Dynamics in Complementary FETs: Quantifying the Role of Self-Heating and Grain Effect Intercoupling
The vertical stacking of sheets and separating them by a dielectric raises severe thermal and geometrical reliability concerns in the complementary field effect transistor (CFET). Using well-calibrated TCAD models, we investigated the impact of the self-heating effect (SHE) and the role of dielectric separation wall (DSW) in electro-thermal coupling. The resulting thermal crosstalk due to DSW shows an increase in temperature of 2.09% (1.60%) at the pFET (nFET) when nFET (pFET) is in the on state. Furthermore, the metal grain granularity (MGG) is a vital factor that affects the electro-thermal characteristics. It offers the randomized metal work function (WF), thereby significantly causing the shift in threshold voltage (Vth). A semi-empirical model is proposed to define the ratio of effective grain size to gate (RGG) area, which provides insight into the grain boundaries and their optimization in CFET. In addition, the significance of the extension region (LEXT) in electro-thermal performance is explored, as LEXT offers series resistance, which modulates thermal resistance. The increase in LEXT from 3 to 7 nm results in decreased lattice temperature (TL) by ~29 K; however, it increases the series resistance and causes the decrease in on current (ION) by 28% (25%) in nFET (pFET). At last, we predicted the device’s lifetime based on Vth shift (i.e., change in V ${}_{\text {th}}= \pm 50$ mV). Thus, the proposed analysis is worth exploring for the reliability-aware CFET design in sub-3 nm nodes.
- 16 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 26 (1) , 365-371
On the Reliability of Complementary Field Effect Transistor: Unveiling the Role of Grain Granularities and Random Fluctuations
This study presents a comprehensive statistical reliability analysis of monolithic Complementary Field Effect Transistors (CFETs), focusing on the impact of process-induced variations. The analysis highlights key sources of variability, including Metal Gate Granularity (MGG), Poly Grain Granularity (PGG), Random Dopant Fluctuation (RDF), and Line Edge Roughness (LER). In smaller geometries, the gate metal (or poly-gate) grain granularities play a significant role in threshold voltage (Vth) variations, raising severe reliability concerns. Through calibrated statistical TCAD simulations, the ON current (ION) variation of 2.82 μA (2.85 μA) is observed in the nFET (pFET) side of CFET, due to MGG for experimentally reported 5 nm grain size. In advanced technologies like high bandwidth memory (HBM), the gate is made of polysilicon that suffers from the PGG in sub-3 nm node devices. The observed coefficient-of-variance (CV) of pFET (2.19) is higher than nFET (1.45), which shows higher variability in pFET due to poly grain size variations. Further, the process-induced RDF and LER significantly alter the Vth. Random numbers are generated by doping atoms in the Voronoi volume of each vertex to quantify the undoped and doped channels to statistically analyze the RDF. In contrast to a doped channel with σVth of 9 mV (7 mV) for nFET (pFET), the undoped scenario yields a default standard deviation (σVth) of 2 mV. To characterize LER, correlation length (Λ) is a prime factor; as Λ approaches the sheet width, CV increases by 24.32% (37.22%) in nFET (pFET). Thus, the results underscore the need for stringent control over grain morphology, doping precision, and edge definition to ensure reliable CFET performance.
- 16 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 26 (1) , 365-371
On the Reliability of Complementary Field Effect Transistor: Unveiling the Role of Grain Granularities and Random Fluctuations
This study presents a comprehensive statistical reliability analysis of monolithic Complementary Field Effect Transistors (CFETs), focusing on the impact of process-induced variations. The analysis highlights key sources of variability, including Metal Gate Granularity (MGG), Poly Grain Granularity (PGG), Random Dopant Fluctuation (RDF), and Line Edge Roughness (LER). In smaller geometries, the gate metal (or poly-gate) grain granularities play a significant role in threshold voltage (Vth) variations, raising severe reliability concerns. Through calibrated statistical TCAD simulations, the ON current (ION) variation of 2.82 μA (2.85 μA) is observed in the nFET (pFET) side of CFET, due to MGG for experimentally reported 5 nm grain size. In advanced technologies like high bandwidth memory (HBM), the gate is made of polysilicon that suffers from the PGG in sub-3 nm node devices. The observed coefficient-of-variance (CV) of pFET (2.19) is higher than nFET (1.45), which shows higher variability in pFET due to poly grain size variations. Further, the process-induced RDF and LER significantly alter the Vth. Random numbers are generated by doping atoms in the Voronoi volume of each vertex to quantify the undoped and doped channels to statistically analyze the RDF. In contrast to a doped channel with σVth of 9 mV (7 mV) for nFET (pFET), the undoped scenario yields a default standard deviation (σVth) of 2 mV. To characterize LER, correlation length (Λ) is a prime factor; as Λ approaches the sheet width, CV increases by 24.32% (37.22%) in nFET (pFET). Thus, the results underscore the need for stringent control over grain morphology, doping precision, and edge definition to ensure reliable CFET performance.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. PP (10709878) , 1
Demonstrating Novel Interbridge Complementary FET: Capacitance Extraction using Dielectric Permittivity Suppression and Conformal Mapping
Complementary FET (CFET) is an astonishing transistor architecture that comprises a self-aligned nFET over pFET separated by a dielectric side wall (DSW), or vice versa, designed to obtain the optimal gate-pitch. To facilitate an enhanced effective channel width without altering the gate pitch, we propose a novel Inter-bridge Complementary FET (IB-CFET) structure in this paper, in which a laterally branched fin-shaped inter-bridge (IB) layer is appended between the self-aligned vertical sheets. The additional IB layer offers a potential improvement in ION/Cgg, gm/Cgg, and RC delay due to an increased overall channel area and reduced capacitance. We developed an analytical model framework for extracting the capacitance and RC delay using conformal mapping and the permittivity suppression technique to capture the gate electrostatics, including interbridges. Considering only nFET is ON, in IB-CFET, the total gate capacitance (Cgg) is contributed: 40% by spacer capacitance (Cspr), 43% by channel (Cch), 4% by outer-fringing (COF), 6% by inter-bridge (CIB), and ~7% by the cumulative capacitance of pFET and dielectric sidewall. IB-CFET shows ~8% lower Cgg than the conventional CFET, i.e., without IB; thereby, offering ~9.95% lower RC delay. Using well-calibrated TCAD models, we extracted the capacitance and RC delay, which is further validated by our proposed model with a tolerable error of ~4%. The extracted ION/Cgg and gm/Cgg of the proposed IB-CFET are improved by 11.40% and 4.08%, respectively, compared to the baseline CFET. Thus, the proposed IB-CFET proves its potential as a promising candidate beyond the 3 nm technology node.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. PP (10709878) , 1
Demonstrating Novel Interbridge Complementary FET: Capacitance Extraction using Dielectric Permittivity Suppression and Conformal Mapping
Complementary FET (CFET) is an astonishing transistor architecture that comprises a self-aligned nFET over pFET separated by a dielectric side wall (DSW), or vice versa, designed to obtain the optimal gate-pitch. To facilitate an enhanced effective channel width without altering the gate pitch, we propose a novel Inter-bridge Complementary FET (IB-CFET) structure in this paper, in which a laterally branched fin-shaped inter-bridge (IB) layer is appended between the self-aligned vertical sheets. The additional IB layer offers a potential improvement in ION/Cgg, gm/Cgg, and RC delay due to an increased overall channel area and reduced capacitance. We developed an analytical model framework for extracting the capacitance and RC delay using conformal mapping and the permittivity suppression technique to capture the gate electrostatics, including interbridges. Considering only nFET is ON, in IB-CFET, the total gate capacitance (Cgg) is contributed: 40% by spacer capacitance (Cspr), 43% by channel (Cch), 4% by outer-fringing (COF), 6% by inter-bridge (CIB), and ~7% by the cumulative capacitance of pFET and dielectric sidewall. IB-CFET shows ~8% lower Cgg than the conventional CFET, i.e., without IB; thereby, offering ~9.95% lower RC delay. Using well-calibrated TCAD models, we extracted the capacitance and RC delay, which is further validated by our proposed model with a tolerable error of ~4%. The extracted ION/Cgg and gm/Cgg of the proposed IB-CFET are improved by 11.40% and 4.08%, respectively, compared to the baseline CFET. Thus, the proposed IB-CFET proves its potential as a promising candidate beyond the 3 nm technology node.
- 9 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (3) , 1698-1704
A Novel De-Mirroring-Based Analytical Model for Capacitance Extraction of Nanosheet FET Using Dielectric Permittivity Suppression
Unlike planar MOSFETs, the Nanosheet FET poses a complex capacitor network that captures the sheet geometry, number of sheets, source-gate-drain contacts, intersheet coupling, etc. To date, the existing compact models predominantly rely on the Cold-FET approach (referred to here as ’mirroring’), in which both gate-to-source (VGS) and drain-to-source (VDS) voltages are set to zero. However, the mirroring assumption breaks down during the saturation regime of operation, necessitating the VDS-dependent capacitance model. Thus, this paper proposes a novel de-mirroring approach for capacitance extraction in Nanosheet FET (NSFET). The device is conceptually cleaved at the center of the channel, allowing separate evaluation of VGS and VDS-dependent capacitances using a conformal mapping technique. The permittivity suppression method is employed to compute the individual capacitance component. The proposed model shows good agreement with simulation data, which has been calibrated against the experimental data. The results demonstrate that the traditional mirroring approach overestimates the overall gate capacitance (Cgg) by ~15%, whereas the proposed de-mirroring approach provides a significantly more accurate prediction.
- 9 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (3) , 1698-1704
A Novel De-Mirroring-Based Analytical Model for Capacitance Extraction of Nanosheet FET Using Dielectric Permittivity Suppression
Unlike planar MOSFETs, the Nanosheet FET poses a complex capacitor network that captures the sheet geometry, number of sheets, source-gate-drain contacts, intersheet coupling, etc. To date, the existing compact models predominantly rely on the Cold-FET approach (referred to here as ’mirroring’), in which both gate-to-source (VGS) and drain-to-source (VDS) voltages are set to zero. However, the mirroring assumption breaks down during the saturation regime of operation, necessitating the VDS-dependent capacitance model. Thus, this paper proposes a novel de-mirroring approach for capacitance extraction in Nanosheet FET (NSFET). The device is conceptually cleaved at the center of the channel, allowing separate evaluation of VGS and VDS-dependent capacitances using a conformal mapping technique. The permittivity suppression method is employed to compute the individual capacitance component. The proposed model shows good agreement with simulation data, which has been calibrated against the experimental data. The results demonstrate that the traditional mirroring approach overestimates the overall gate capacitance (Cgg) by ~15%, whereas the proposed de-mirroring approach provides a significantly more accurate prediction.
- 24 September 2025
- Published by Elsevier in Solid-State Electronics
- Vol. 230
Statistical analysis of random dopant fluctuation in Complementary FET
- 24 September 2025
- Published by Elsevier in Solid-State Electronics
- Vol. 230
Statistical analysis of random dopant fluctuation in Complementary FET
- 18 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (3) , 1682-1687
The Role of Dielectric Wall in Forksheet FET: Exploring Electrical-Thermal Intercoupling
In this paper, we investigate the role of the dielectric wall (DW) in Forksheet FET (FSFET), to explore the electrical-thermal intercoupling. The DW present between N/P spaces significantly influences the operating mechanism, and the transparency/opacity of the DW raises severe reliability issues. The thermal coupling effect (TCE) is explained by considering the self-heating effect (SHE) at N/P sides individually and with the heat leak through DW, i.e., inter-spaces coupling. Further, the electrical coupling between n/pFET of the FSFET induces the DW capacitance that modulates the rate of carrier inversion on either side. Using well-calibrated TCAD models, we investigate the heat and E-field transfer through DW while considering the DW extension into the channel, resulting in effective ION/Cgg modulation. The resultant impact of the proposed assessment is seen on the basic circuit, i.e., a three-stage ring oscillator, is realized for both common and isolated gate configurations. Thus, the proposed guidelines are important in exploring a reliable and robust FSFET design.
- 18 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 33 (3) , 1682-1687
The Role of Dielectric Wall in Forksheet FET: Exploring Electrical-Thermal Intercoupling
In this paper, we investigate the role of the dielectric wall (DW) in Forksheet FET (FSFET), to explore the electrical-thermal intercoupling. The DW present between N/P spaces significantly influences the operating mechanism, and the transparency/opacity of the DW raises severe reliability issues. The thermal coupling effect (TCE) is explained by considering the self-heating effect (SHE) at N/P sides individually and with the heat leak through DW, i.e., inter-spaces coupling. Further, the electrical coupling between n/pFET of the FSFET induces the DW capacitance that modulates the rate of carrier inversion on either side. Using well-calibrated TCAD models, we investigate the heat and E-field transfer through DW while considering the DW extension into the channel, resulting in effective ION/Cgg modulation. The resultant impact of the proposed assessment is seen on the basic circuit, i.e., a three-stage ring oscillator, is realized for both common and isolated gate configurations. Thus, the proposed guidelines are important in exploring a reliable and robust FSFET design.
- Open Access
- 30 August 2025
- Published by Elsevier in Solid-State Electronics
- Vol. 230
Assessing the impact of process and design variations on reliability of complementary FET
- 30 August 2025
- Published by Elsevier in Solid-State Electronics
- Vol. 230
Open AccessAssessing the impact of process and design variations on reliability of complementary FET