Aleksandr A. Kiushov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Aleksandr A. Kiushov has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Irina Gennadievna Panova
Department of Chemistry, M.V. Lomonosov Moscow State University, Leninskie Gory 1, 119991 Moscow, Russia
5 shared publications - Alexander Yaroslavov
Department of Chemistry, M.V. Lomonosov Moscow State University, Leninskie Gory 1, 119991 Moscow, Russia
3 shared publications - Maxim S. Arzhakov
Department of Chemistry, M.V. Lomonosov Moscow State University, Leninskie Gory 1, 119991 Moscow, Russia
3 shared publications Alexander A. Yaroslavov
Department of Chemistry, M.V. Lomonosov Moscow State University, Moscow, Russian Federation
2 shared publications- Pavel Krasilnikov
Moscow State University, Moscow, Russia
2 shared publications Aleksandr Anatol'EVich Yaroslavov
Department of Chemistry, M. V. Lomonosov Moscow State University, 119991 Moscow, Russian Federation
1 shared publication
Latest Publications
- 11 November 2026
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 34 (12) , 307
Anti-Erosion and Water-Retaining Ameliorants Based on Biodegradable Polysaccharides
- 11 November 2026
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 34 (12) , 307
Anti-Erosion and Water-Retaining Ameliorants Based on Biodegradable Polysaccharides
- Open Access
The Effect of Natural Chitosan, Humate and Their Complexes on the Rheological Properties of Wet Kaolinite
Control of mechanical properties of natural clays and clayey soils under saturation with water is an important task in agriculture and geoengineering. In this study, kaolinite was modified with cationic chitosan, anionic potassium humate (PHum), and non-stoichiometric chitosan–PHum interpolyelectrolyte complexes (IPCs). The optimal composition of IPCs in terms of the ratio between positively charged chitosan groups and negatively charged potassium humate groups, Q = []/[COO−], was determined using laser microelectrophoresis, turbidimetry, and dynamic light scattering and showed Q ≤ 0.3 for anionic IPCs and Q ≥ 3 for cationic IPCs. Amplitude tests showed that introduction of minor amounts of chitosan, not more than 0.5 wt.%, to kaolinite resulted in increased strength characteristics of wet clay by 0.5–1.5 orders of magnitude, which was due to the formation of the cooperative physical network via electrostatic interaction between positively charged chitosan and negatively charged clay particles. Binding of the same amounts of anionic PHum to kaolinite decreased the strength parameters by 0.5–1.0 orders of magnitude because of increased sliding of the clay particles. Addition of 0.25 wt.% of both cationic and anionic IPCs to kaolinite allowed the preservation of the reinforcing effect of chitosan and suppression of the weakening action of PHum. Such behavior of chitosan–PHum IPCs was likely due to redistribution of cationic chitosan between anionic PHum and kaolinite and formation of the kaolinite–chitosan–PHum ternary complex, which minimizes the destabilizing effect of PHum and improves the mechanical properties of the clay.Open AccessThe Effect of Natural Chitosan, Humate and Their Complexes on the Rheological Properties of Wet Kaolinite
Control of mechanical properties of natural clays and clayey soils under saturation with water is an important task in agriculture and geoengineering. In this study, kaolinite was modified with cationic chitosan, anionic potassium humate (PHum), and non-stoichiometric chitosan–PHum interpolyelectrolyte complexes (IPCs). The optimal composition of IPCs in terms of the ratio between positively charged chitosan groups and negatively charged potassium humate groups, Q = []/[COO−], was determined using laser microelectrophoresis, turbidimetry, and dynamic light scattering and showed Q ≤ 0.3 for anionic IPCs and Q ≥ 3 for cationic IPCs. Amplitude tests showed that introduction of minor amounts of chitosan, not more than 0.5 wt.%, to kaolinite resulted in increased strength characteristics of wet clay by 0.5–1.5 orders of magnitude, which was due to the formation of the cooperative physical network via electrostatic interaction between positively charged chitosan and negatively charged clay particles. Binding of the same amounts of anionic PHum to kaolinite decreased the strength parameters by 0.5–1.0 orders of magnitude because of increased sliding of the clay particles. Addition of 0.25 wt.% of both cationic and anionic IPCs to kaolinite allowed the preservation of the reinforcing effect of chitosan and suppression of the weakening action of PHum. Such behavior of chitosan–PHum IPCs was likely due to redistribution of cationic chitosan between anionic PHum and kaolinite and formation of the kaolinite–chitosan–PHum ternary complex, which minimizes the destabilizing effect of PHum and improves the mechanical properties of the clay. - 1 January 2026
- Published by OOO Zhurnal "Mendeleevskie Soobshcheniya" in Mendeleev Communications
- Vol. 36 (3)
Polymer formulations for preventing wind and water erosion of saline soil
A loamy soil with a high salt content containing mainly sodium cations and sulfate anions has a loose topsoil and is susceptible to air and water erosion. Covering the soil with sand mulch followed by treatment with heterofunctional polysaccharide xanthan gum or non-ionic synthetic polyvinyl alcohol results in the formation of mechanically stable coatings over the sand mulch layer. Mulching saline soils with sand followed by treatment with polymers is a promising method for creating protective anti-erosion coatings.
- 1 January 2026
- Published by OOO Zhurnal "Mendeleevskie Soobshcheniya" in Mendeleev Communications
- Vol. 36 (3)
Polymer formulations for preventing wind and water erosion of saline soil
A loamy soil with a high salt content containing mainly sodium cations and sulfate anions has a loose topsoil and is susceptible to air and water erosion. Covering the soil with sand mulch followed by treatment with heterofunctional polysaccharide xanthan gum or non-ionic synthetic polyvinyl alcohol results in the formation of mechanically stable coatings over the sand mulch layer. Mulching saline soils with sand followed by treatment with polymers is a promising method for creating protective anti-erosion coatings.
- Open Access
Mechanically Activated Transition from Linear Viscoelasticity to Yielding: Correlation-Based Unification
The mechanically activated transition (MAT) from linear viscoelasticity to yielding is considered an essential part of the operational behavior of ductile materials. The MAT region is restricted by proportional limit at σ0 and ε0 and the yield point at σy and εy, or, in terms of this paper, and ε0 and and εy, respectively. This stage precedes yielding and controls the parameters of the yield point. For bulk plastic (co)polymers and cellular polymeric foams, the quantitative correlations between , ε0, and εy were determined. The ratios and were specified as yielding criteria. For all the samples studied, their mechanical response within the MAT region was unified in terms of master curve constructed via re-calculation of the experimental “stress–strain” diagrams in the reduced coordinates where and ε are the current modulus and strain, respectively. To generalize these regularities found for bulk plastics and foams, our earlier experimental results concerning the rheology of soil-based pastes and data from the literature concerning the computer simulation of plastic deformation were invoked. Master curves for (1) dispersed pastes, (2) bulk plastics, (3) polymeric foams, and (4) various virtual models were shown to be in satisfactory coincidence. For the materials analyzed, this result was considered as the unification of their mechanical response within the MAT region. An algorithm for the express analysis of the mechanical response of plastic systems within the MAT region is proposed. The limitations and advances of the proposed methodological approach based on correlation studies followed by construction of master curves are outlined.Open AccessMechanically Activated Transition from Linear Viscoelasticity to Yielding: Correlation-Based Unification
The mechanically activated transition (MAT) from linear viscoelasticity to yielding is considered an essential part of the operational behavior of ductile materials. The MAT region is restricted by proportional limit at σ0 and ε0 and the yield point at σy and εy, or, in terms of this paper, and ε0 and and εy, respectively. This stage precedes yielding and controls the parameters of the yield point. For bulk plastic (co)polymers and cellular polymeric foams, the quantitative correlations between , ε0, and εy were determined. The ratios and were specified as yielding criteria. For all the samples studied, their mechanical response within the MAT region was unified in terms of master curve constructed via re-calculation of the experimental “stress–strain” diagrams in the reduced coordinates where and ε are the current modulus and strain, respectively. To generalize these regularities found for bulk plastics and foams, our earlier experimental results concerning the rheology of soil-based pastes and data from the literature concerning the computer simulation of plastic deformation were invoked. Master curves for (1) dispersed pastes, (2) bulk plastics, (3) polymeric foams, and (4) various virtual models were shown to be in satisfactory coincidence. For the materials analyzed, this result was considered as the unification of their mechanical response within the MAT region. An algorithm for the express analysis of the mechanical response of plastic systems within the MAT region is proposed. The limitations and advances of the proposed methodological approach based on correlation studies followed by construction of master curves are outlined. - Open Access
A Dramatic Change in Rheological Behavior of a Clay Material Caused by a Minor Addition of Hydrophilic and Amphiphilic Polyelectrolytes
Wide usage of clay-based materials in industry requires investigations concerning efficient modification techniques to control their mechanical behavior in aqueous media. The challenging problem in this field involves minimization of the modifying agent content to provide marked changes in the operating characteristics of the material. In this work, the physicochemical, mechanical and structural aspects of the interaction of capillary water-saturated kaolinite with polyelectrolytes were studied. Modification of kaolinite with a negligible amount (0.1 wt.%) of hydrophilic and amphiphilic polyelectrolytes provides the control for rheological parameters of kaolinite suspensions such as storage and loss modulus in the range of three orders of magnitude. The results obtained reveal the wide possibilities for the production of a spectrum of clay materials using minor amounts of polymer modifying agents.
Open AccessA Dramatic Change in Rheological Behavior of a Clay Material Caused by a Minor Addition of Hydrophilic and Amphiphilic Polyelectrolytes
Wide usage of clay-based materials in industry requires investigations concerning efficient modification techniques to control their mechanical behavior in aqueous media. The challenging problem in this field involves minimization of the modifying agent content to provide marked changes in the operating characteristics of the material. In this work, the physicochemical, mechanical and structural aspects of the interaction of capillary water-saturated kaolinite with polyelectrolytes were studied. Modification of kaolinite with a negligible amount (0.1 wt.%) of hydrophilic and amphiphilic polyelectrolytes provides the control for rheological parameters of kaolinite suspensions such as storage and loss modulus in the range of three orders of magnitude. The results obtained reveal the wide possibilities for the production of a spectrum of clay materials using minor amounts of polymer modifying agents.