Zihong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zihong Li has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Ning Zhang
School of Mechanical Engineering, Southeast University, Nanjing 211189, China
5 shared publications - Cheng Wang
School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh, U.K.
2 shared publications - Hangyu Lu
Institute of Intelligent Vehicles, Shanghai Jiao Tong University, Shanghai, China
2 shared publications - Chenghao Sang
School of Mechanical Engineering, Yangzhou University, Yangzhou 225009, China
1 shared publication Dawei Pi
Nanjing University of Science and Technology
1 shared publication- Fang Ye
Department of Mechanical Engineering, Imperial College London, London SW7 2AZ, UK
1 shared publication
Latest Publications
- Open Access
A New Shaped Disturbance Observer to Improve Stability in a Time-Delayed Steering Control System for a Corner Module
Conventional disturbance observers improve disturbance rejection in steer-by-wire corner modules. However, feedback delay and higher observer gain strengthen the compensation–delay coupling, aggravating wheel-angle vibration and shrinking the closed-loop stability region. To address this conflict, a shaped disturbance observer is proposed. The shaped disturbance observer improves the estimation of time-varying wheel-end disturbance torque, while a shaping filter reconfigures the magnitude and phase characteristics of the compensation channel. Based on the corner module dynamics, a delay-dependent closed-loop characteristic equation is derived, and stability boundaries are evaluated using frequency-domain boundary curves and characteristic roots. With the observers tuned using a common nominal error-pole location, the shaped disturbance observer exhibits smaller estimation phase lag at all four tested frequencies, while its root mean square estimation error varies relative to that of the conventional disturbance observer with disturbance frequency. Under identical feedback delays, its stability region area is 8.3–91.4% larger than that of the conventional disturbance observer. Simulation results quantify the trade-offs among disturbance estimation accuracy, compensation bandwidth, and closed-loop stability.
Open AccessA New Shaped Disturbance Observer to Improve Stability in a Time-Delayed Steering Control System for a Corner Module
Conventional disturbance observers improve disturbance rejection in steer-by-wire corner modules. However, feedback delay and higher observer gain strengthen the compensation–delay coupling, aggravating wheel-angle vibration and shrinking the closed-loop stability region. To address this conflict, a shaped disturbance observer is proposed. The shaped disturbance observer improves the estimation of time-varying wheel-end disturbance torque, while a shaping filter reconfigures the magnitude and phase characteristics of the compensation channel. Based on the corner module dynamics, a delay-dependent closed-loop characteristic equation is derived, and stability boundaries are evaluated using frequency-domain boundary curves and characteristic roots. With the observers tuned using a common nominal error-pole location, the shaped disturbance observer exhibits smaller estimation phase lag at all four tested frequencies, while its root mean square estimation error varies relative to that of the conventional disturbance observer with disturbance frequency. Under identical feedback delays, its stability region area is 8.3–91.4% larger than that of the conventional disturbance observer. Simulation results quantify the trade-offs among disturbance estimation accuracy, compensation bandwidth, and closed-loop stability.
- 29 September 2026
- Published by SAGE Publications in Journal of Vibration and Control
Stability and gain analysis of a robust steering control system for a corner module with hybrid time delay
In distributed vehicles with corner modules, independent wheel steering improves chassis motion freedom but weakens mechanical constraints and increases reliance on the X-by-wire feedback chain. This makes wheel-end steering more sensitive to kingpin disturbances and time delays. Existing studies on disturbance rejection for steering systems often ignore feedback delays or simplify them as a single continuous delay, which may distort stability prediction and gain selection. To address this issue, a composite closed-loop model for a disturbance-observer-based corner-module steering system is proposed by introducing the disturbance estimation error into the state vector. Continuous actuator delay and sampling-induced discrete delay are formulated as a hybrid feedback delay. Based on the resulting hybrid-delay model, the semi-discretization method is used to construct the characteristic matrix, and the stability region in the ( K P , K D ) plane is obtained from Floquet multipliers. The results show that the proposed method extracts the stability boundary of the hybrid-delay system and divides the stable region into low frequency, high frequency, and zero phase angle regions according to the dominant multiplier phase. An optimal gain point with fast convergence and weak oscillation is identified using the dominant multiplier modulus and the normalized convergence index based on the step size. Compared with an equivalent continuous-delay model, the hybrid-delay model gives different optimal gains and a higher convergence index as the sampling-delay ratio increases.
- 29 September 2026
- Published by SAGE Publications in Journal of Vibration and Control
Stability and gain analysis of a robust steering control system for a corner module with hybrid time delay
In distributed vehicles with corner modules, independent wheel steering improves chassis motion freedom but weakens mechanical constraints and increases reliance on the X-by-wire feedback chain. This makes wheel-end steering more sensitive to kingpin disturbances and time delays. Existing studies on disturbance rejection for steering systems often ignore feedback delays or simplify them as a single continuous delay, which may distort stability prediction and gain selection. To address this issue, a composite closed-loop model for a disturbance-observer-based corner-module steering system is proposed by introducing the disturbance estimation error into the state vector. Continuous actuator delay and sampling-induced discrete delay are formulated as a hybrid feedback delay. Based on the resulting hybrid-delay model, the semi-discretization method is used to construct the characteristic matrix, and the stability region in the ( K P , K D ) plane is obtained from Floquet multipliers. The results show that the proposed method extracts the stability boundary of the hybrid-delay system and divides the stable region into low frequency, high frequency, and zero phase angle regions according to the dominant multiplier phase. An optimal gain point with fast convergence and weak oscillation is identified using the dominant multiplier modulus and the normalized convergence index based on the step size. Compared with an equivalent continuous-delay model, the hybrid-delay model gives different optimal gains and a higher convergence index as the sampling-delay ratio increases.
- Open Access
Impacts of the Observation of the Steering Torque Disturbance on the Stability of a Time-Delayed Control System for a Corner Module with Steering
Corner modules decouple chassis functions and enable independent wheel steering, but their control is highly sensitive to external disturbances and feedback delays. Disturbance observers (DObs) are often introduced to mitigate such disturbances, yet their additional dynamics can also compromise closed-loop stability when delays are present. This paper establishes the closed-loop control system of a corner module steering system based on its dynamics, designs the corresponding control law, and incorporates a DOb. Classical stability analysis is carried out using D-curve mapping and eigenvalue validation. The results reveal that feedback delay progressively shrinks the stable domain. When a DOb is introduced, disturbance rejection is improved; however, the admissible control gain region becomes narrower, and larger observer gains further constrain the derivative action, generating additional unstable regions. This paper mechanistically elucidates the impact of disturbance observation on the stability of a time-delayed control system for a corner module with steering.
Open AccessImpacts of the Observation of the Steering Torque Disturbance on the Stability of a Time-Delayed Control System for a Corner Module with Steering
Corner modules decouple chassis functions and enable independent wheel steering, but their control is highly sensitive to external disturbances and feedback delays. Disturbance observers (DObs) are often introduced to mitigate such disturbances, yet their additional dynamics can also compromise closed-loop stability when delays are present. This paper establishes the closed-loop control system of a corner module steering system based on its dynamics, designs the corresponding control law, and incorporates a DOb. Classical stability analysis is carried out using D-curve mapping and eigenvalue validation. The results reveal that feedback delay progressively shrinks the stable domain. When a DOb is introduced, disturbance rejection is improved; however, the admissible control gain region becomes narrower, and larger observer gains further constrain the derivative action, generating additional unstable regions. This paper mechanistically elucidates the impact of disturbance observation on the stability of a time-delayed control system for a corner module with steering.
- Open Access
A New Hybrid Rigid–Flexible Coupling Modeling for Efficient Vibration Analysis of the Cooling System of New Energy Vehicles
The cooling system is a core component for a vehicle’s powertrains to operate smoothly and maintain a satisfying noise, vibration, and harshness (NVH) performance. However, advances in new energy vehicles bring with them complex requirements for the cooling fan design due to new issues such as increased heat load, dynamic variations, and high-speed vibrations, which demand the optimization of fan dynamics over a wide range of parameters. In this paper, by thoroughly checking the effect of rigid–flexible coupling and the geometrically complex elastic frame of the fan, we propose a combined modeling approach to reduce the computational time of broad-range parameter variation analysis and examine the vibration problem in the cooling fans under various external excitations. First, the complicated frame of the fan is simplified through virtual prototyping based on an experiment. Then, modal transition is applied, reducing the complex kinetic expression, and a time-invariant system model is derived with multi-blade coordinate transformation. Stability and bifurcation analysis are performed regarding different excitation couplings from the rotor, powertrain, and road. The results of the simulation and experiment illustrate that the proposed methodology achieves a substantial reduction in computational time, and all degrees of freedom (DOFs) are divided into two groups including symmetrical and asymmetrical types. The results also imply the great potential for the optimization and control of the high-speed fan’s vibration for new energy cars.
Open AccessA New Hybrid Rigid–Flexible Coupling Modeling for Efficient Vibration Analysis of the Cooling System of New Energy Vehicles
The cooling system is a core component for a vehicle’s powertrains to operate smoothly and maintain a satisfying noise, vibration, and harshness (NVH) performance. However, advances in new energy vehicles bring with them complex requirements for the cooling fan design due to new issues such as increased heat load, dynamic variations, and high-speed vibrations, which demand the optimization of fan dynamics over a wide range of parameters. In this paper, by thoroughly checking the effect of rigid–flexible coupling and the geometrically complex elastic frame of the fan, we propose a combined modeling approach to reduce the computational time of broad-range parameter variation analysis and examine the vibration problem in the cooling fans under various external excitations. First, the complicated frame of the fan is simplified through virtual prototyping based on an experiment. Then, modal transition is applied, reducing the complex kinetic expression, and a time-invariant system model is derived with multi-blade coordinate transformation. Stability and bifurcation analysis are performed regarding different excitation couplings from the rotor, powertrain, and road. The results of the simulation and experiment illustrate that the proposed methodology achieves a substantial reduction in computational time, and all degrees of freedom (DOFs) are divided into two groups including symmetrical and asymmetrical types. The results also imply the great potential for the optimization and control of the high-speed fan’s vibration for new energy cars.
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (6) , 14177-14188
Multiobjective Optimization of Powertrain Mode Switching With Hysteresis Control for Electric Heavy-Duty Vehicles
The powertrain of electric heavy-duty vehicles (HDVs) is typically composed of multiple motors and multispeed transmissions, leading to a diverse range of operating modes. Due to the highly dynamic driving conditions and the necessity to optimize energy consumption, the powertrain undergoes frequent mode switching, which negatively impacts ride comfort. This article proposes a multiobjective optimization method for mode switching with hysteresis control, where the hysteresis control effectively enhances driving comfort by setting appropriate hysteresis values. The optimal hysteresis value is determined by solving the Pareto front to balance energy consumption and ride comfort. The results demonstrated that the proposed method effectively balanced three cost functions, leading to significant reductions in gear shifting (e.g., 48.5% in C-WTVC) and motor switching (e.g., 51.0% in C-WTVC) with only a minimal increase in energy consumption (e.g., 1.1% in C-WTVC). The performance of the proposed method was validated through comparisons with the benchmark under six global standard driving cycles, confirming its effectiveness even without explicit cost function boundaries. This multiobjective optimization approach can be widely applied in the development of EMS that incorporate hysteresis control.
- 3 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (6) , 14177-14188
Multiobjective Optimization of Powertrain Mode Switching With Hysteresis Control for Electric Heavy-Duty Vehicles
The powertrain of electric heavy-duty vehicles (HDVs) is typically composed of multiple motors and multispeed transmissions, leading to a diverse range of operating modes. Due to the highly dynamic driving conditions and the necessity to optimize energy consumption, the powertrain undergoes frequent mode switching, which negatively impacts ride comfort. This article proposes a multiobjective optimization method for mode switching with hysteresis control, where the hysteresis control effectively enhances driving comfort by setting appropriate hysteresis values. The optimal hysteresis value is determined by solving the Pareto front to balance energy consumption and ride comfort. The results demonstrated that the proposed method effectively balanced three cost functions, leading to significant reductions in gear shifting (e.g., 48.5% in C-WTVC) and motor switching (e.g., 51.0% in C-WTVC) with only a minimal increase in energy consumption (e.g., 1.1% in C-WTVC). The performance of the proposed method was validated through comparisons with the benchmark under six global standard driving cycles, confirming its effectiveness even without explicit cost function boundaries. This multiobjective optimization approach can be widely applied in the development of EMS that incorporate hysteresis control.