Marcel Schmickler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marcel Schmickler has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Anjana Devi
Leibniz Institute for Solid State and Materials Research
4 shared publications - Anna Lena Giesecke
Fraunhofer IMS
2 shared publications - Detlef Rogalla
RUBION Ruhr University Bochum Bochum Germany
2 shared publications Emad Najafidehaghani
Leibniz Institute for Solid State and Materials Research, IFW Dresden
2 shared publications- Harish Parala
Leibniz Institute for Solid State and Materials Research, IFW Dresden
2 shared publications - Ivan Kaban
Leibniz Institute for Solid State and Materials Research
2 shared publications
Latest Publications
- Open Access
- 3 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (12) , 4992-5006
Tunable Texture in ZnO Thin Films on 200 mm Wafers: Comparative Study of Zn(DMP) 2 and Diethylzinc Precursors for ALD
- 3 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (12) , 4992-5006
Open AccessTunable Texture in ZnO Thin Films on 200 mm Wafers: Comparative Study of Zn(DMP) 2 and Diethylzinc Precursors for ALD
- Open Access
- 16 March 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (12) , 18380-18393
Defect Engineering in Atomic-Layer-Deposited Cerium Oxide
This study explores the role of atomic layer deposition (ALD) as an enabling technique for the defect engineering of catalytically active ultrathin deposits. In particular, we demonstrate the feasibility of tuning the O/Ce ratio in thermal ALD-based cerium oxide layers grown on silicon-based or alumina substrates by using the organometallic precursor tris(N, N'-diisopropyl-2-dimethylamido-guanidinato)cerium(III) ([Ce(dpdmg)3]) with H2O, O2, or O3 as coreactants. As revealed by in situ X-ray photoelectron spectroscopy (XPS), the Ce3+ concentration, i.e., the concentration of oxygen vacancies, depends strongly on three factors: the type of oxygen source, the chosen substrate, and the film thickness. The fixation of Ce3+ states during the early stages of growth is primarily determined by interface formation and the appearance of silicate and aluminate species, along with changes in morphology and surface-to-volume ratio. For thicker deposits (>5 nm), the intrinsic oxygen vacancies are coreactant-dependent. Furthermore, the chosen oxygen source also influences the morphology of ultrathin deposits, enabling potential surface functionalization with ceria nanoislands of varying composition and size. We point to a likely connection between this chemical and morphological tuning and changes in the ALD reaction pathway. The evolution of different nitrogen and carbon species depends on the oxygen source and the number of ALD cycles, indicating a shift in the ALD reaction mechanism from ligand exchange using H2O to ligand combustion for O3. The comprehensive investigation of these growth parameters is crucial for tailoring film properties via precise defect engineering.
- 16 March 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (12) , 18380-18393
Open AccessDefect Engineering in Atomic-Layer-Deposited Cerium Oxide
This study explores the role of atomic layer deposition (ALD) as an enabling technique for the defect engineering of catalytically active ultrathin deposits. In particular, we demonstrate the feasibility of tuning the O/Ce ratio in thermal ALD-based cerium oxide layers grown on silicon-based or alumina substrates by using the organometallic precursor tris(N, N'-diisopropyl-2-dimethylamido-guanidinato)cerium(III) ([Ce(dpdmg)3]) with H2O, O2, or O3 as coreactants. As revealed by in situ X-ray photoelectron spectroscopy (XPS), the Ce3+ concentration, i.e., the concentration of oxygen vacancies, depends strongly on three factors: the type of oxygen source, the chosen substrate, and the film thickness. The fixation of Ce3+ states during the early stages of growth is primarily determined by interface formation and the appearance of silicate and aluminate species, along with changes in morphology and surface-to-volume ratio. For thicker deposits (>5 nm), the intrinsic oxygen vacancies are coreactant-dependent. Furthermore, the chosen oxygen source also influences the morphology of ultrathin deposits, enabling potential surface functionalization with ceria nanoislands of varying composition and size. We point to a likely connection between this chemical and morphological tuning and changes in the ALD reaction pathway. The evolution of different nitrogen and carbon species depends on the oxygen source and the number of ALD cycles, indicating a shift in the ALD reaction mechanism from ligand exchange using H2O to ligand combustion for O3. The comprehensive investigation of these growth parameters is crucial for tailoring film properties via precise defect engineering.
- Open Access
- 11 February 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Atomic Layer Deposition of Textured ZnO on 200 mm Wafers for Device Applications
Zinc oxide (ZnO) is a technologically important wide-bandgap semiconductor used in optoelectronics, sensing, and transparent electronic devices. Implementing ZnO thin films in such devices requires scalable, uniform, and compatible thin-film deposition methods. Atomic layer deposition (ALD) provides precise control over film thickness, composition, and conformality, and is a well-adapted process in the semiconductor industry. ALD processes for growing ZnO primarily rely on the pyrophoric diethylzinc (DEZ) precursor. Recently, Bis-3-(N,N-dimethylamino)propyl zinc ([Zn(DMP) 2 ]) has emerged as a promising non-pyrophoric alternative, providing improved handling safety and enhanced thermal stability. However, its use has so far been limited to growth on small substrates in proof-of-concept experiments. In this work, a thermal ALD process using [Zn(DMP) 2 ] with H 2 O as precursors was developed on industrially-relevant 200 mm silicon wafers and compared to an established thermal process with DEZ and H 2 O. The effects of deposition temperature (150-300 °C), film thickness, and the underlying substrate material on film growth were systematically investigated. Structural, morphological, chemical, and electrical properties were evaluated using complementary and advanced materials characterization techniques. Across the entire 200 mm wafer area, ZnO films deposited from [Zn(DMP) 2 ] exhibit excellent thickness uniformity and a nearstoichiometric composition comparable to those obtained with DEZ. While slightly higher resistivity and reduced crystallinity are seen at lower deposition temperatures, higher deposition temperatures yield comparable resistivity and an improved c-axis oriented crystalline texture. Importantly, successful lithographic patterning and electrical characterization of van der Pauw devices confirm compatibility with advanced fabrication workflows. These results demonstrate that [Zn(DMP) 2 ] can compete with DEZ in film quality on large-area wafers and is safer to handle, which is a significant advantage overall.
- 11 February 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessAtomic Layer Deposition of Textured ZnO on 200 mm Wafers for Device Applications
Zinc oxide (ZnO) is a technologically important wide-bandgap semiconductor used in optoelectronics, sensing, and transparent electronic devices. Implementing ZnO thin films in such devices requires scalable, uniform, and compatible thin-film deposition methods. Atomic layer deposition (ALD) provides precise control over film thickness, composition, and conformality, and is a well-adapted process in the semiconductor industry. ALD processes for growing ZnO primarily rely on the pyrophoric diethylzinc (DEZ) precursor. Recently, Bis-3-(N,N-dimethylamino)propyl zinc ([Zn(DMP) 2 ]) has emerged as a promising non-pyrophoric alternative, providing improved handling safety and enhanced thermal stability. However, its use has so far been limited to growth on small substrates in proof-of-concept experiments. In this work, a thermal ALD process using [Zn(DMP) 2 ] with H 2 O as precursors was developed on industrially-relevant 200 mm silicon wafers and compared to an established thermal process with DEZ and H 2 O. The effects of deposition temperature (150-300 °C), film thickness, and the underlying substrate material on film growth were systematically investigated. Structural, morphological, chemical, and electrical properties were evaluated using complementary and advanced materials characterization techniques. Across the entire 200 mm wafer area, ZnO films deposited from [Zn(DMP) 2 ] exhibit excellent thickness uniformity and a nearstoichiometric composition comparable to those obtained with DEZ. While slightly higher resistivity and reduced crystallinity are seen at lower deposition temperatures, higher deposition temperatures yield comparable resistivity and an improved c-axis oriented crystalline texture. Importantly, successful lithographic patterning and electrical characterization of van der Pauw devices confirm compatibility with advanced fabrication workflows. These results demonstrate that [Zn(DMP) 2 ] can compete with DEZ in film quality on large-area wafers and is safer to handle, which is a significant advantage overall.
- Open Access
- 4 November 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (2) , 971-987
Atomic layer deposition of NiO x : harnessing the potential of new precursor combinations for photoelectrochemical water oxidation
Atomic layer deposition enables the fabrication of uniform, conformal, and pinhole-free thin films with precise sub-nanometer thickness control. This work presents the first report of thermal ALD of NiOx using two nickel precursors –Alanis™ and [Ni(ipki)2]– in combination with two different oxidising agents (H2O and O3), over a temperature range of 75-250°C. The Alanis/O3 composition exhibited one of the highest growth per cycle (1.2Å) and a broad ALD window between 100-175°C. In contrast, the Alanis/H2O and [Ni(ipki)2]/O3 combinations yielded lower growth rates of 0.74Å at 150°C and 0.40Å at 250°C, respectively. Comprehensive structural, morphological, optical, and chemical characterisations revealed that the choice of precursor combination and the reaction temperature significantly impact the film composition, strongly influencing its suitability for various applications. Notably, those parameters closely determined the photoelectrochemical performance and the stability of the Si/NiOx-based photoanode towards oxygen evolution reaction. Photoelectrodes fabricated with Alanis/O3 at 200°C demonstrate stability exceeding 24H and exhibit a remarkable OER onset potential of 1.15V vs RHE for a photocurrent density of 1mA·cm-2.
- 4 November 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (2) , 971-987
Open AccessAtomic layer deposition of NiO x : harnessing the potential of new precursor combinations for photoelectrochemical water oxidation
Atomic layer deposition enables the fabrication of uniform, conformal, and pinhole-free thin films with precise sub-nanometer thickness control. This work presents the first report of thermal ALD of NiOx using two nickel precursors –Alanis™ and [Ni(ipki)2]– in combination with two different oxidising agents (H2O and O3), over a temperature range of 75-250°C. The Alanis/O3 composition exhibited one of the highest growth per cycle (1.2Å) and a broad ALD window between 100-175°C. In contrast, the Alanis/H2O and [Ni(ipki)2]/O3 combinations yielded lower growth rates of 0.74Å at 150°C and 0.40Å at 250°C, respectively. Comprehensive structural, morphological, optical, and chemical characterisations revealed that the choice of precursor combination and the reaction temperature significantly impact the film composition, strongly influencing its suitability for various applications. Notably, those parameters closely determined the photoelectrochemical performance and the stability of the Si/NiOx-based photoanode towards oxygen evolution reaction. Photoelectrodes fabricated with Alanis/O3 at 200°C demonstrate stability exceeding 24H and exhibit a remarkable OER onset potential of 1.15V vs RHE for a photocurrent density of 1mA·cm-2.
- Open Access
- 3 September 2025
- Published by Elsevier in Applied Surface Science Advances
- Vol. 29
Low-temperature, high-throughput spatial atomic layer deposition of NiOx nanocrystalline thin films from [Ni(ipki)2]
- 3 September 2025
- Published by Elsevier in Applied Surface Science Advances
- Vol. 29
Open AccessLow-temperature, high-throughput spatial atomic layer deposition of NiOx nanocrystalline thin films from [Ni(ipki)2]