Juliana Sebolt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Juliana Sebolt has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chang-Beom Eom
Department of Materials Science and Engineering, University of Wisconsin-Madison 2 , Madison, Wisconsin 53706
2 shared publications - Jeremy Levy
University of Pittsburgh
2 shared publications - Jieun Kim
Department of Materials Science and Engineering, University of Wisconsin-Madison 4 , Madison, Wisconsin 53706
2 shared publications Kyoungjun Lee
Department of Materials Science and Engineering, University of Wisconsin-Madison 4 , Madison, Wisconsin 53706
2 shared publications- Patrick Irvin
Department of Physics and Astronomy, University of Pittsburgh 1 , Pittsburgh, Pennsylvania 15260
2 shared publications - Anton V. Ievlev
Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
1 shared publication
Latest Publications
- 5 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (14)
Annealing SrTiO3 produces an iron-rich surface layer
SrTiO3 (STO) is among the most widely used substrates in complex oxide heterostructure research, yet the role of its trace impurity content in determining interface properties remains poorly understood. Here, we show that high-temperature annealing (the standard procedure for preparing TiO2-terminated STO surfaces) universally drives Fe impurities from the substrate bulk to the surface, forming a sharp, delta-like distribution within a few nanometers of the surface. Using time-of-flight secondary ion mass spectrometry with nanometer-scale depth resolution, we find that Fe is largely undetectable before annealing but appears prominently at the surface after annealing in all 16 substrates surveyed from three independent commercial suppliers. A systematic study on pieces diced from a single substrate demonstrates that surface Fe concentration increases with both annealing temperature and duration, following thermally activated, diffusion-limited kinetics with an activation energy of approximately 3 eV. Density functional theory calculations confirm a thermodynamic preference for Fe substitution near the STO surface, establishing the driving force for segregation. This annealing-induced redistribution effectively deposits a hidden layer of magnetic impurities within a few nanometers of the surface. These results have direct implications for complex oxide heterostructures such as LaAlO3/SrTiO3, where annealing-dependent Fe accumulation at the STO surface may account for the widely reported magnetic signatures at such interfaces.
- 5 October 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (14)
Annealing SrTiO3 produces an iron-rich surface layer
SrTiO3 (STO) is among the most widely used substrates in complex oxide heterostructure research, yet the role of its trace impurity content in determining interface properties remains poorly understood. Here, we show that high-temperature annealing (the standard procedure for preparing TiO2-terminated STO surfaces) universally drives Fe impurities from the substrate bulk to the surface, forming a sharp, delta-like distribution within a few nanometers of the surface. Using time-of-flight secondary ion mass spectrometry with nanometer-scale depth resolution, we find that Fe is largely undetectable before annealing but appears prominently at the surface after annealing in all 16 substrates surveyed from three independent commercial suppliers. A systematic study on pieces diced from a single substrate demonstrates that surface Fe concentration increases with both annealing temperature and duration, following thermally activated, diffusion-limited kinetics with an activation energy of approximately 3 eV. Density functional theory calculations confirm a thermodynamic preference for Fe substitution near the STO surface, establishing the driving force for segregation. This annealing-induced redistribution effectively deposits a hidden layer of magnetic impurities within a few nanometers of the surface. These results have direct implications for complex oxide heterostructures such as LaAlO3/SrTiO3, where annealing-dependent Fe accumulation at the STO surface may account for the widely reported magnetic signatures at such interfaces.
- Open Access
- 3 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (9)
Nanoscale control of LaAlO3/SrTiO3 conductance beyond the polar catastrophe
Conductive atomic force microscope (c-AFM) lithography can be utilized to create a wide range of LaAlO3/SrTiO3 (LAO/STO)-based nanoelectronic devices in a reconfigurable manner. Experiments were generally performed with intrinsically insulating LAO/STO heterostructures, with LAO thickness less than the critical value at which a polar catastrophe takes place [<4 unit cell (u.c.)]. Here, we use inductively coupled plasma reactive ion etching (ICPRIE) to fabricate c-AFM “canvases” on intrinsically conducting LAO/STO samples with ≥4 u.c. LAO. We observe that its interfacial two-dimensional electron gas (2DEG) can be pinched off and then switched back on by c-AFM lithography. Nanowires created with initially conductive LAO/STO interfaces have an order-of-magnitude longer lifetime in ambient conditions, when compared to an identically created 3.4 u.c. LAO/STO nanowire. We also demonstrate key nanoscale properties such as ballistic transport in a quasi-one-dimensional electron waveguide at a 5 u.c. LAO/STO interface. This approach frees c-AFM-written nanodevice designs from time constraints in air associated with <4 u.c. LAO/STO heterostructures.
- 3 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (9)
Open AccessNanoscale control of LaAlO3/SrTiO3 conductance beyond the polar catastrophe
Conductive atomic force microscope (c-AFM) lithography can be utilized to create a wide range of LaAlO3/SrTiO3 (LAO/STO)-based nanoelectronic devices in a reconfigurable manner. Experiments were generally performed with intrinsically insulating LAO/STO heterostructures, with LAO thickness less than the critical value at which a polar catastrophe takes place [<4 unit cell (u.c.)]. Here, we use inductively coupled plasma reactive ion etching (ICPRIE) to fabricate c-AFM “canvases” on intrinsically conducting LAO/STO samples with ≥4 u.c. LAO. We observe that its interfacial two-dimensional electron gas (2DEG) can be pinched off and then switched back on by c-AFM lithography. Nanowires created with initially conductive LAO/STO interfaces have an order-of-magnitude longer lifetime in ambient conditions, when compared to an identically created 3.4 u.c. LAO/STO nanowire. We also demonstrate key nanoscale properties such as ballistic transport in a quasi-one-dimensional electron waveguide at a 5 u.c. LAO/STO interface. This approach frees c-AFM-written nanodevice designs from time constraints in air associated with <4 u.c. LAO/STO heterostructures.