Leonhard Gertlowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Leonhard Gertlowski has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Christoph Broeckmann
Institute of Applied Powder Metallurgy and Ceramics at RWTH Aachen e.V., Aachen, Germany
3 shared publications- Christoph Broeckmann
RWTH Aachen University
3 shared publications - Oliver Schenk
RWTH Aachen University, Institute for Materials Applications in Mechanical Engineering
3 shared publications - Felix Weber
Institute for Materials Applications in Mechanical Engineering, RWTH Aachen University, 52062 Aachen, Germany
2 shared publications - Santiago Benito
Institute for Materials Chair of Materials Technology Ruhr University Bochum Universitätsstraße 150 Bochum Nordrhein‐Westfalen Germany
2 shared publications Sebastian Weber
Chair of Materials Technology
2 shared publications
Latest Publications
- 11 October 2026
- Published by European Powder Metallurgy Association
Micromechanical Investigation Of Carbide-Matrix Interfaces In High-Speed Steels
Hot forming tools are subjected to thermo-mechanical load cycles, leading to an out-of-phase relation between mechanical strain and surface temperature. During tool-workpiece contact, compressive stresses arise from thermally constrained expansion of the heated tool surface, whereas tool retraction and subsequent cooling induce tensile stresses, promoting thermo-mechanical fatigue (TMF). Consequently, failure may occur either in the martensitic matrix, the carbides or at their interface. In this context, failure at the carbide-matrix interface of two powder-metallurgical (PM) high-speed steels (HSS) consolidated by hot isostatic pressing (HIP) is investigated by micro-tensile testing. An optimized test geometry fabricated by focused ion beam (FIB) milling is employed to ensure a homogeneous uniaxial stress state in the gauge section, each containing a single carbide to provoke interfacial failure. The load is applied by nanoindentation, while strain is measured using digital image correlation (DIC). The resulting stress-strain curves are evaluated and the fracture behaviour is investigated.
- 11 October 2026
- Published by European Powder Metallurgy Association
Micromechanical Investigation Of Carbide-Matrix Interfaces In High-Speed Steels
Hot forming tools are subjected to thermo-mechanical load cycles, leading to an out-of-phase relation between mechanical strain and surface temperature. During tool-workpiece contact, compressive stresses arise from thermally constrained expansion of the heated tool surface, whereas tool retraction and subsequent cooling induce tensile stresses, promoting thermo-mechanical fatigue (TMF). Consequently, failure may occur either in the martensitic matrix, the carbides or at their interface. In this context, failure at the carbide-matrix interface of two powder-metallurgical (PM) high-speed steels (HSS) consolidated by hot isostatic pressing (HIP) is investigated by micro-tensile testing. An optimized test geometry fabricated by focused ion beam (FIB) milling is employed to ensure a homogeneous uniaxial stress state in the gauge section, each containing a single carbide to provoke interfacial failure. The load is applied by nanoindentation, while strain is measured using digital image correlation (DIC). The resulting stress-strain curves are evaluated and the fracture behaviour is investigated.
- Open Access
- 11 June 2026
- Published by SAGE Publications in Powder Metallurgy
- Vol. 69 (5) , 468-473
Accelerated fatigue testing of powder metallurgical HIP high-speed steel for near-net shape applications
High-speed steels are commonly used for cutting tools requiring a high impact toughness and fatigue resistance. Both properties are significantly enhanced by employing the powder metallurgical (PM) production route using HIP as consolidation technique. However, the inherent oxides of the used powder may reduce the fatigue limit. Hence, subsequent forging is commonly required, which in turn precludes the possibility of near net shape production by PM. The purpose of this study is to investigate the efficiency of an isothermal holding stage that is introduced prior to the application of pressure to allow oxide size reduction during the HIP process and thereby increasing fatigue limit. The fatigue limit is assessed by accelerated fatigue testing, allowing its determination with a single specimen, which is particularly crucial for HIP processes with limited capsule volume. Good agreement is observed with results from conventional fatigue testing based on the staircase method.
- 11 June 2026
- Published by SAGE Publications in Powder Metallurgy
- Vol. 69 (5) , 468-473
Open AccessAccelerated fatigue testing of powder metallurgical HIP high-speed steel for near-net shape applications
High-speed steels are commonly used for cutting tools requiring a high impact toughness and fatigue resistance. Both properties are significantly enhanced by employing the powder metallurgical (PM) production route using HIP as consolidation technique. However, the inherent oxides of the used powder may reduce the fatigue limit. Hence, subsequent forging is commonly required, which in turn precludes the possibility of near net shape production by PM. The purpose of this study is to investigate the efficiency of an isothermal holding stage that is introduced prior to the application of pressure to allow oxide size reduction during the HIP process and thereby increasing fatigue limit. The fatigue limit is assessed by accelerated fatigue testing, allowing its determination with a single specimen, which is particularly crucial for HIP processes with limited capsule volume. Good agreement is observed with results from conventional fatigue testing based on the staircase method.
- Open Access
- 8 May 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 681
Characterization of the grain boundary strength of polycrystalline NMC811 using in situ micro tensile tests
- 8 May 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 681
Open AccessCharacterization of the grain boundary strength of polycrystalline NMC811 using in situ micro tensile tests
- Open Access
- 17 March 2026
- Published by Elsevier in SSRN Electronic Journal
Characterization of the grain boundary strength of polycrystalline NMC811 using in situ micro tensile tests
LiNixCoyMn1–x–yO2 (NMC) is one of the most relevant lithium-ion battery cathode materials. In this study, micromechanical tests were used to examine the fracture behavior of LiNi0.8Co0.1Mn0.1O2 (NMC811) secondary particles. Furthermore, the grain boundary strength was measured and the grain boundary stiffness was estimated to 521GPaµm−1. Using an optimized push-to-pull sample geometry produced by focused ion beam (FIB) technology and measuring the displacement through digital image correlation (DIC), micro tensile tests were performed and validated against nanoindentation. A Weibull distribution characteristic tensile strength of 745MPa followed by a brittle fracture behavior was measured. The fracture surface was examined and showed an intercrystalline fracture. Through electron backscatter diffraction (EBSD) analysis, less frequently occurring transcrystalline fracture was detected. Scanning transmission electron microscopy (STEM) showed a slight increase in dislocation density within the testing section in comparison to reference positions. The results can be used for a more detailed understanding of the mechanical degradation during the cycling of batteries as well as for building accurate simulation models.
- 17 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCharacterization of the grain boundary strength of polycrystalline NMC811 using in situ micro tensile tests
LiNixCoyMn1–x–yO2 (NMC) is one of the most relevant lithium-ion battery cathode materials. In this study, micromechanical tests were used to examine the fracture behavior of LiNi0.8Co0.1Mn0.1O2 (NMC811) secondary particles. Furthermore, the grain boundary strength was measured and the grain boundary stiffness was estimated to 521GPaµm−1. Using an optimized push-to-pull sample geometry produced by focused ion beam (FIB) technology and measuring the displacement through digital image correlation (DIC), micro tensile tests were performed and validated against nanoindentation. A Weibull distribution characteristic tensile strength of 745MPa followed by a brittle fracture behavior was measured. The fracture surface was examined and showed an intercrystalline fracture. Through electron backscatter diffraction (EBSD) analysis, less frequently occurring transcrystalline fracture was detected. Scanning transmission electron microscopy (STEM) showed a slight increase in dislocation density within the testing section in comparison to reference positions. The results can be used for a more detailed understanding of the mechanical degradation during the cycling of batteries as well as for building accurate simulation models.
- Open Access
- 8 March 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (6) , 2156-2166
Accelerated Fatigue Testing of High‐Speed Steel
The staircase method is commonly employed in the characterization of metals to determine their fatigue limit. In this approach, the stress amplitude is systematically varied around the assumed fatigue limit in consecutive tests. However, its applicability for in‐process optimization in alloy design and development is limited by the large number of specimens required—particularly for high‐speed steels (HSSs), which exhibit pronounced scatter in fatigue limit—resulting in long testing times. To address this limitation, accelerated fatigue testing is applied to HSS for the first time in the present study. The stress amplitude is continuously increased within a single experiment while recording the specimen temperature, enabling the fatigue limit to be estimated from the dissipated energy of a single specimen and thereby reducing both material consumption and testing time. The applicability of the accelerated fatigue testing method is demonstrated for an ingot‐cast HSS (AISI M2) and a powder‐metallurgical (PM) HSS (AISI M3 Class 2) fabricated by hot isostatic pressing (HIP) as consolidation technique. In addition, the fatigue limits of both materials are determined using the conventional staircase method at various highly loaded volumes (HLVs) to characterize the defect distribution and to validate the results obtained from accelerated testing.
- 8 March 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (6) , 2156-2166
Open AccessAccelerated Fatigue Testing of High‐Speed Steel
The staircase method is commonly employed in the characterization of metals to determine their fatigue limit. In this approach, the stress amplitude is systematically varied around the assumed fatigue limit in consecutive tests. However, its applicability for in‐process optimization in alloy design and development is limited by the large number of specimens required—particularly for high‐speed steels (HSSs), which exhibit pronounced scatter in fatigue limit—resulting in long testing times. To address this limitation, accelerated fatigue testing is applied to HSS for the first time in the present study. The stress amplitude is continuously increased within a single experiment while recording the specimen temperature, enabling the fatigue limit to be estimated from the dissipated energy of a single specimen and thereby reducing both material consumption and testing time. The applicability of the accelerated fatigue testing method is demonstrated for an ingot‐cast HSS (AISI M2) and a powder‐metallurgical (PM) HSS (AISI M3 Class 2) fabricated by hot isostatic pressing (HIP) as consolidation technique. In addition, the fatigue limits of both materials are determined using the conventional staircase method at various highly loaded volumes (HLVs) to characterize the defect distribution and to validate the results obtained from accelerated testing.
- 11 September 2025
- Published by European Powder Metallurgy Association
Accelerated Fatigue Testing Of PM-HIP High-speed Steel
High-speed steels are commonly used for cutting tools that require a high impact toughness and fatigue resistance. Both properties are significantly enhanced by employing the powder metallurgical production (PM) route using hot isostatic pressing (HIP) as consolidation technique. The fatigue strength is conventionally assessed by Wöhler tests that imply a systematic variation of the stress amplitude in the vicinity of the presumed load limit, employing multiple specimens. However, the available test volume is limited by the size of the HIP capsule. Hence, an accelerated fatigue testing method is presented that can significantly reduce the use of material and time by determining the fatigue limit with a single specimen. This method involves the measurement of the temperature rise in a sample during a load increase test whose characteristic course indicates damage initiation. Its validity is demonstrated by the determination of the fatigue limit for HS6-5-3 employing both accelerated and conventional testing.
- 11 September 2025
- Published by European Powder Metallurgy Association
Accelerated Fatigue Testing Of PM-HIP High-speed Steel
High-speed steels are commonly used for cutting tools that require a high impact toughness and fatigue resistance. Both properties are significantly enhanced by employing the powder metallurgical production (PM) route using hot isostatic pressing (HIP) as consolidation technique. The fatigue strength is conventionally assessed by Wöhler tests that imply a systematic variation of the stress amplitude in the vicinity of the presumed load limit, employing multiple specimens. However, the available test volume is limited by the size of the HIP capsule. Hence, an accelerated fatigue testing method is presented that can significantly reduce the use of material and time by determining the fatigue limit with a single specimen. This method involves the measurement of the temperature rise in a sample during a load increase test whose characteristic course indicates damage initiation. Its validity is demonstrated by the determination of the fatigue limit for HS6-5-3 employing both accelerated and conventional testing.