Tomas Martan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tomas Martan has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- David Mares
Department of Microelectronics, Faculty of Electrical Engineering, Czech Technical University, Prague, Czech Republic
2 shared publications - V. Prajzler
Czech Technical University in Prague, Faculty of Electrical Engineering, Department of Microelectronics, Technická 2, 166 27 Prague, Czech Republic
2 shared publications - Ivan Kašík
Institute of Photonics and Electronics, Czech Academy of Sciences, Prague, Czechia
1 shared publication - J. Šmejcký1 shared publication
- Jiri Kanka
Institute of Animal Physiology and Genetics of the Czech Academy of Sciences Libechov Czech Republic
1 shared publication - Pavla Nekvindová
Department of Inorganic Chemistry University of Chemistry and Technology Prague Czech Republic
1 shared publication
Latest Publications
- 16 September 2025
- Published by Elsevier in Optics Communications
- Vol. 596
Gain determination of new erbium-bismuth doped germanium silicate optical glass for double-band optical amplification
- 16 September 2025
- Published by Elsevier in Optics Communications
- Vol. 596
Gain determination of new erbium-bismuth doped germanium silicate optical glass for double-band optical amplification
- 21 October 2022
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 375, 132887
Local detection of gaseous carbon dioxide using optical fibers and fiber tapers of single-cell dimensions
- 21 October 2022
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 375, 132887
Local detection of gaseous carbon dioxide using optical fibers and fiber tapers of single-cell dimensions
- Open Access
- 8 September 2009
- Published by Taylor & Francis in International Journal of Optomechatronics
- Vol. 3 (3) , 233-249
Theoretical Analysis and Preparation of Tapered Suspended Core Microstructure Fibers
Suspended core microstructured optical fibers (SC-MOFs) represent a special kind of microstructured fibers which can be employed for optical sensing. In this article one experimental SC-MOF and its tapers were numerically analyzed in order to determine if the overlap of evanescent waves with the fiber cladding holes can be increased by tapering. Power distributions of fundamental modes in the SC-MOF and its tapers were calculated by using a vectorial finite element method. The calculations have shown that the evanescent wave overlap (at a wavelength of 1550 nm) can be increased from 0.75% up to 26% by tapering of a section of the SC-MOF from an original diameter of 125 µm down to 31.25 µm. Fiber tapers designed on the basis of the numerical analysis were prepared by so-called ‘flame brush technique’ employing a fiber puller of own construction. Experiments with the prepared tapers have proved that the cladding holes remain sufficiently large for passing liquid and gas analytes through and that the core diameter of the untapered pigtails is large enough for low-loss coupling of optical beams into the tapered fiber.
- 8 September 2009
- Published by Taylor & Francis in International Journal of Optomechatronics
- Vol. 3 (3) , 233-249
Open AccessTheoretical Analysis and Preparation of Tapered Suspended Core Microstructure Fibers
Suspended core microstructured optical fibers (SC-MOFs) represent a special kind of microstructured fibers which can be employed for optical sensing. In this article one experimental SC-MOF and its tapers were numerically analyzed in order to determine if the overlap of evanescent waves with the fiber cladding holes can be increased by tapering. Power distributions of fundamental modes in the SC-MOF and its tapers were calculated by using a vectorial finite element method. The calculations have shown that the evanescent wave overlap (at a wavelength of 1550 nm) can be increased from 0.75% up to 26% by tapering of a section of the SC-MOF from an original diameter of 125 µm down to 31.25 µm. Fiber tapers designed on the basis of the numerical analysis were prepared by so-called ‘flame brush technique’ employing a fiber puller of own construction. Experiments with the prepared tapers have proved that the cladding holes remain sufficiently large for passing liquid and gas analytes through and that the core diameter of the untapered pigtails is large enough for low-loss coupling of optical beams into the tapered fiber.