Mingyang Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mingyang Sun has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Hong Yang
State Key Laboratory of Fabrication Technologies for Integrated Circuits, Institute of Microelectronics of the Chinese Academy of Sciences, Beijing, China
3 shared publications - Huaxiang Yin
Institute of Microelectronics, Chinese Academy of Sciences
3 shared publications - Jun Luo
School of Advanced Interdisciplinary Sciences, University of Chinese Academy of Sciences, Beijing, China
3 shared publications Wenwu Wang
State Key Laboratory of Fabrication Technologies for Integrated Circuits and the Institute of Microelectronics, Beijing, China
3 shared publications- Xiaolei Wang
Institute of Microelectronics, Chinese Academy of Sciences
3 shared publications Bo Tang
State Key Laboratory of Fabrication Technologies for Integrated Circuits and the Institute of Microelectronics, Beijing, China
2 shared publications
Latest Publications
- 23 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 104-109
Lateral Sensing of Hot-Carrier-Induced Trap Distribution via DIBL Degradation Analysis in Nanoscale n-FinFET
In this article, the drain-induced barrier lowering (DIBL) is taken as a smart indicator for the lateral positioning of hot-carrier-induced trap distribution. A distinct asymmetry in DIBL due to hot-carrier degradation (HCD) is observed upon source/drain swapping. The ratio of DIBL degradation at normal source/drain configuration and reverse mode is defined as the P parameter, which is less than 1 to indicate the trap generation at the source side and larger than 1 for the drain side. With $P$ parameter extraction in nanoscale n-FinFET, it is found that the oxide traps initially dominate and shift from the source to the drain, and then, interface traps take over and shift from the drain toward the source, when ${V}_{\text {ds}}$ increases from 1.3 to 3.5V with ${V}_{\text {gs}}$ of 1.4 and 1.8 V under HCD stress. This observed shift highlights the crucial role of impact ionization (I/I)-generated secondary carriers in shaping the lateral damage profile. Based on these experimental findings, a physical model is proposed and conclusively verified through TCAD simulations, offering a predictive framework for reliability assessment.
- 23 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 104-109
Lateral Sensing of Hot-Carrier-Induced Trap Distribution via DIBL Degradation Analysis in Nanoscale n-FinFET
In this article, the drain-induced barrier lowering (DIBL) is taken as a smart indicator for the lateral positioning of hot-carrier-induced trap distribution. A distinct asymmetry in DIBL due to hot-carrier degradation (HCD) is observed upon source/drain swapping. The ratio of DIBL degradation at normal source/drain configuration and reverse mode is defined as the P parameter, which is less than 1 to indicate the trap generation at the source side and larger than 1 for the drain side. With $P$ parameter extraction in nanoscale n-FinFET, it is found that the oxide traps initially dominate and shift from the source to the drain, and then, interface traps take over and shift from the drain toward the source, when ${V}_{\text {ds}}$ increases from 1.3 to 3.5V with ${V}_{\text {gs}}$ of 1.4 and 1.8 V under HCD stress. This observed shift highlights the crucial role of impact ionization (I/I)-generated secondary carriers in shaping the lateral damage profile. Based on these experimental findings, a physical model is proposed and conclusively verified through TCAD simulations, offering a predictive framework for reliability assessment.
- Open Access
- 10 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 14, 30-35
Dynamic Evolution of Hydrogen in IGZO Transistors for PBTI Improvement by Low-Temperature Atmosphere Annealing
In this paper, we investigate the evolution of hydrogen (H) behavior in back-gated IGZO/HfO. transistors subjected to low-temperature annealing (200 °C in air), focusing on its impact on initial electrical characteristics (Id-Vg) and positive bias temperature instability (PBTI). For initial electrical performance, a negative threshold voltage shift is observed in the Id-Vg curve after annealing. Combined with X-ray photoelectron spectroscopy (XPS) analysis, this shift is attributed to an increase in hydroxyl-related hydrogen within the IGZO layer. Regarding device reliability, a model-based decoupling analysis is employed to separate the contributions of electron trapping (e-trapping) and hydrogen doping (H-doping). The results reveal that hydrogen-induced degradation is suppressed by approximately 10.67% to 26.02% after annealing. Based on this, a physical model for H states in IGZO/HfO2 films during annealing was proposed. These results offer new insight into the role of hydrogen in IGZO devices and provide a theoretical and experimental foundation for the optimization of H-doping during process integration.
- 10 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 14, 30-35
Open AccessDynamic Evolution of Hydrogen in IGZO Transistors for PBTI Improvement by Low-Temperature Atmosphere Annealing
In this paper, we investigate the evolution of hydrogen (H) behavior in back-gated IGZO/HfO. transistors subjected to low-temperature annealing (200 °C in air), focusing on its impact on initial electrical characteristics (Id-Vg) and positive bias temperature instability (PBTI). For initial electrical performance, a negative threshold voltage shift is observed in the Id-Vg curve after annealing. Combined with X-ray photoelectron spectroscopy (XPS) analysis, this shift is attributed to an increase in hydroxyl-related hydrogen within the IGZO layer. Regarding device reliability, a model-based decoupling analysis is employed to separate the contributions of electron trapping (e-trapping) and hydrogen doping (H-doping). The results reveal that hydrogen-induced degradation is suppressed by approximately 10.67% to 26.02% after annealing. Based on this, a physical model for H states in IGZO/HfO2 films during annealing was proposed. These results offer new insight into the role of hydrogen in IGZO devices and provide a theoretical and experimental foundation for the optimization of H-doping during process integration.
- Open Access
- 19 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. PP, 1
Impact of TiN Thickness Uniformity on the Reliability of n-FinFETs
This work investigates the impact of Titanium Nitride (TiN) thickness uniformity on the electrical performance and reliability by comparing n-type FinFETs with TiN layers fabricated using physical vapor deposition (PVD) and atomic layer deposition (ALD), respectively. While both device types exhibit similar threshold voltages ( 24 mV), the FinFETs with non-uniform TiN thickness demonstrate significantly worse reliability under Bias Temperature Instability (BTI) and Hot Carrier Degradation (HCD) stress conditions (11% and 24%). Through comprehensive electrical characterization and TCAD simulations, the observed degradation is attributed to spatial variations in the TiN work function, which induce stronger localized electric fields. These localized fields accelerate interface and oxide trap generation, leading to higher threshold voltage shifts and trap densities. The results highlight the importance of TiN thickness uniformity in suppressing degradation mechanisms and ensuring high-performance, reliable FinFET operation.
- 19 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. PP, 1
Open AccessImpact of TiN Thickness Uniformity on the Reliability of n-FinFETs
This work investigates the impact of Titanium Nitride (TiN) thickness uniformity on the electrical performance and reliability by comparing n-type FinFETs with TiN layers fabricated using physical vapor deposition (PVD) and atomic layer deposition (ALD), respectively. While both device types exhibit similar threshold voltages ( 24 mV), the FinFETs with non-uniform TiN thickness demonstrate significantly worse reliability under Bias Temperature Instability (BTI) and Hot Carrier Degradation (HCD) stress conditions (11% and 24%). Through comprehensive electrical characterization and TCAD simulations, the observed degradation is attributed to spatial variations in the TiN work function, which induce stronger localized electric fields. These localized fields accelerate interface and oxide trap generation, leading to higher threshold voltage shifts and trap densities. The results highlight the importance of TiN thickness uniformity in suppressing degradation mechanisms and ensuring high-performance, reliable FinFET operation.