Dhivakar Poosapadi
Dhivakar Poosapadi has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- A. Rami Reddy
Department of Freshman Engineering, Lakireddy Bali Reddy College of Engineering (Affiliated to JNTUK), Mylavaram, India
1 shared publication - Ashwin Sailesh
Department of Mechanical Engineering Sri Sairam Institute of Technology 600044 Chennai Tamil Nadu India
1 shared publication - G. Ramya
Department of Mechanical Engineering, Rajalakshmi Engineering College, Chennai, India
1 shared publication - G. Senthilkumar
Department of Mechanical Engineering, Panimalar Engineering College, Chennai, India
1 shared publication - Grandhi Venkata Krishna Pradeep
Department of Mechanical Engineering, Aditya University, Surampalem, India
1 shared publication - Itha Veeranjaneyulu
Department of Mechanical Engineering, Aditya University, Surampalem, India
1 shared publication
Latest Publications
- Open Access
- 24 October 2024
- Published by Dewspublication
- Vol. 20 (6) , 504-519
Advancements in Wire Arc Additive Manufacturing of Functionally Graded Materials: Optimizing Compositional Gradients and Mechanical Performance: An Overview
Wire Arc Additive Manufacturing (WAAM) is an advanced 3D metal printing technique that enables the fabrication of complex, large-scale components with minimal material waste. Its ability to control deposition parameters has made it particularly useful for creating Functionally Graded Materials (FGMs), which exhibit a gradual variation in composition and structure. This paper explores recent advancements in the fabrication of FGMs using WAAM, focusing on material combinations, process optimization, and the resulting microstructural and mechanical properties. Through numerical analysis, it was observed that controlling the wire feed rate and deposition speed significantly influences the mechanical properties, including tensile strength and hardness. For instance, increasing the wire feed rate from 2 mm/s to 8 mm/s improved the ultimate tensile strength by 15%, but a further increase led to a 10% reduction due to incomplete fusion between layers. Additionally, post-processing techniques such as laser polishing reduced surface roughness by up to 80%, significantly enhancing the component's performance in wear-sensitive applications. This study highlights the importance of optimizing process parameters and post-processing techniques to enhance the functionality and reliability of FGMs fabricated by WAAM.
- 24 October 2024
- Published by Dewspublication
- Vol. 20 (6) , 504-519
Open AccessAdvancements in Wire Arc Additive Manufacturing of Functionally Graded Materials: Optimizing Compositional Gradients and Mechanical Performance: An Overview
Wire Arc Additive Manufacturing (WAAM) is an advanced 3D metal printing technique that enables the fabrication of complex, large-scale components with minimal material waste. Its ability to control deposition parameters has made it particularly useful for creating Functionally Graded Materials (FGMs), which exhibit a gradual variation in composition and structure. This paper explores recent advancements in the fabrication of FGMs using WAAM, focusing on material combinations, process optimization, and the resulting microstructural and mechanical properties. Through numerical analysis, it was observed that controlling the wire feed rate and deposition speed significantly influences the mechanical properties, including tensile strength and hardness. For instance, increasing the wire feed rate from 2 mm/s to 8 mm/s improved the ultimate tensile strength by 15%, but a further increase led to a 10% reduction due to incomplete fusion between layers. Additionally, post-processing techniques such as laser polishing reduced surface roughness by up to 80%, significantly enhancing the component's performance in wear-sensitive applications. This study highlights the importance of optimizing process parameters and post-processing techniques to enhance the functionality and reliability of FGMs fabricated by WAAM.
- Open Access
- 26 September 2024
- Published by Dewspublication
- Vol. 20 (12) , 181-190
Characterization of Mechanical and Viscoelastic Properties of Glass Fibre Reinforced Polymer Composites
This study investigates the mechanical and Viscoelastic properties of glass fibre reinforced polymer (GFRP) composites, focusing on improvements in performance due to the incorporation of glass fibres. The GFRP composites were fabricated using E-glass fibres embedded in an SC-15 epoxy resin matrix. Tensile, flexural, and dynamic mechanical analysis (DMA) tests were conducted to characterize the properties of the composites. The results showed a 30% increase in tensile strength and a 25% improvement in elastic modulus compared to neat epoxy resin. The tensile strength of the GFRP composite was found to be 489 MPa, while the modulus of elasticity increased to 24.5 GPa. In flexural testing, the GFRP composites exhibited a 20% increase in flexural strength, reaching 600 MPa, and a 15% improvement in flexural modulus, measured at 22 GPa. Additionally, the dynamic mechanical analysis demonstrated a 40% increase in storage modulus, with the composites maintaining stiffness across a temperature range from 30°C to 180°C. The glass transition temperature (Tg) increased by 10°C, indicating improved thermal stability. These enhancements are attributed to the effective load transfer between the glass fibres and the epoxy matrix, as well as improved fibre-matrix adhesion due to silane surface treatment. This study provides critical insights into the mechanical behaviour and thermal stability of GFRP composites, underscoring their potential for high-performance structural applications, including aerospace and marine engineering.
- 26 September 2024
- Published by Dewspublication
- Vol. 20 (12) , 181-190
Open AccessCharacterization of Mechanical and Viscoelastic Properties of Glass Fibre Reinforced Polymer Composites
This study investigates the mechanical and Viscoelastic properties of glass fibre reinforced polymer (GFRP) composites, focusing on improvements in performance due to the incorporation of glass fibres. The GFRP composites were fabricated using E-glass fibres embedded in an SC-15 epoxy resin matrix. Tensile, flexural, and dynamic mechanical analysis (DMA) tests were conducted to characterize the properties of the composites. The results showed a 30% increase in tensile strength and a 25% improvement in elastic modulus compared to neat epoxy resin. The tensile strength of the GFRP composite was found to be 489 MPa, while the modulus of elasticity increased to 24.5 GPa. In flexural testing, the GFRP composites exhibited a 20% increase in flexural strength, reaching 600 MPa, and a 15% improvement in flexural modulus, measured at 22 GPa. Additionally, the dynamic mechanical analysis demonstrated a 40% increase in storage modulus, with the composites maintaining stiffness across a temperature range from 30°C to 180°C. The glass transition temperature (Tg) increased by 10°C, indicating improved thermal stability. These enhancements are attributed to the effective load transfer between the glass fibres and the epoxy matrix, as well as improved fibre-matrix adhesion due to silane surface treatment. This study provides critical insights into the mechanical behaviour and thermal stability of GFRP composites, underscoring their potential for high-performance structural applications, including aerospace and marine engineering.