Byungchan Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Byungchan Lee has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Ngoc Le Trinh
Department of Materials Science and Engineering, Incheon National University, Incheon 22012, Korea
2 shared publications - Youngho Kang
Department of Materials Science and Engineering Incheon National University Incheon Republic of Korea
2 shared publications - Aravind H. Patil
Department of Materials Science and Engineering, Incheon National University, Incheon 22012, Korea
1 shared publication Byungchan Lee
Department of Materials Science and Engineering, Incheon National University, Incheon 22012, Korea
1 shared publicationChi Thang Nguyen
Department of Materials Science and Engineering, Incheon National University, Incheon 22012, Korea
1 shared publication- Chi Thang Nguyen
Applied Materials Division Argonne National Laboratory Lemont Illinois USA
1 shared publication
Latest Publications
- 3 March 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (10) , 5035-5049
Tuning surface reactivity pathways through molecular inhibitor redosing for precision nanopatterning
Area-selective atomic layer deposition (AS-ALD) has emerged as a promising bottom-up approach for achieving precise 3D patterning in advanced nanofabrication. In this study, Ru AS-ALD on SiO2 versus Si3N4 surfaces was investigated using cyclohexane carboxaldehyde (CHAD) as a small molecule inhibitor (SMI). CHAD exhibited selective adsorption on Si3N4 , enabling the selective deposition of Ru when (tricarbonyl-(trimethylenemethane)-ruthenium (TRuST) and H2O were used as the precursor and reactant, respectively. A re-dosing strategy, validated by Monte Carlo (MC) simulation, was introduced to improve deposition selectivity. Compared to single dose of CHAD, which showed selectivity against Ru for 7 nm (50 cycles), the re-dosing strategy improved up to 27 nm (200 cycles). This improvement of selectivity was mainly due to high inhibitor adsorption density, which reduced unoccupied adsorption sites that could act as nucleation sites for precursors. The optimized Ru AS-ALD with re-dosing strategy was applied to 2D line patterns and 3D trench patterns, consisting of SiO2/Si3N4. 2D patterns achieved 26.5 nm (200 cycles) of selective deposition, accompanied by an undesirable lateral growth of 18.8 nm.Conversely, 3D patterns achieved 15 nm (100 cycles) of selective growth without lateral growth observation. The critical growth difference is mainly attributed to surface topology: 3D trench structures provide a more effective physical and chemical barrier compared to 2D structures.Consequently, the results collectively demonstrate the potential of the re-dosing strategy in selectivity improvement and the critical role of topography in achieving reliable AS-ALD for 3D nanofabrication.
- 3 March 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (10) , 5035-5049
Tuning surface reactivity pathways through molecular inhibitor redosing for precision nanopatterning
Area-selective atomic layer deposition (AS-ALD) has emerged as a promising bottom-up approach for achieving precise 3D patterning in advanced nanofabrication. In this study, Ru AS-ALD on SiO2 versus Si3N4 surfaces was investigated using cyclohexane carboxaldehyde (CHAD) as a small molecule inhibitor (SMI). CHAD exhibited selective adsorption on Si3N4 , enabling the selective deposition of Ru when (tricarbonyl-(trimethylenemethane)-ruthenium (TRuST) and H2O were used as the precursor and reactant, respectively. A re-dosing strategy, validated by Monte Carlo (MC) simulation, was introduced to improve deposition selectivity. Compared to single dose of CHAD, which showed selectivity against Ru for 7 nm (50 cycles), the re-dosing strategy improved up to 27 nm (200 cycles). This improvement of selectivity was mainly due to high inhibitor adsorption density, which reduced unoccupied adsorption sites that could act as nucleation sites for precursors. The optimized Ru AS-ALD with re-dosing strategy was applied to 2D line patterns and 3D trench patterns, consisting of SiO2/Si3N4. 2D patterns achieved 26.5 nm (200 cycles) of selective deposition, accompanied by an undesirable lateral growth of 18.8 nm.Conversely, 3D patterns achieved 15 nm (100 cycles) of selective growth without lateral growth observation. The critical growth difference is mainly attributed to surface topology: 3D trench structures provide a more effective physical and chemical barrier compared to 2D structures.Consequently, the results collectively demonstrate the potential of the re-dosing strategy in selectivity improvement and the critical role of topography in achieving reliable AS-ALD for 3D nanofabrication.
- 11 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (37) , 19316-19329
Functionalization of Si 3 N 4 with an aldehyde inhibitor for area selective deposition of HfO 2 and SiO 2
Area selective deposition of HfO 2 and SiO 2 using BAD inhibitor.
- 11 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (37) , 19316-19329
Functionalization of Si 3 N 4 with an aldehyde inhibitor for area selective deposition of HfO 2 and SiO 2
Area selective deposition of HfO 2 and SiO 2 using BAD inhibitor.