Mengming Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mengming Wang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Chenzhen Ji
College of Automotive and Energy Engineering, Tongji University 1 , 4800 Cao'an Road, Shanghai 201804
2 shared publications - Tong Zhu
College of Automotive and Energy Engineering, Tongji University 1 , 4800 Cao'an Road, Shanghai 201804
2 shared publications - Caichao Zheng
College of Automotive and Energy Engineering, Tongji University 1 , 4800 Cao'an Road, Shanghai 201804
1 shared publication - Chuang Gao
Shanghai Advanced Research Institute, Chinese Academy of Sciences, Shanghai, China
1 shared publication - Dan Zhao
Department of Mechanical Engineering, College of Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140, New Zealand
1 shared publication Enlei Ke
School of Mechanical Engineering, Tongji University 1 , 4800 Cao'an Road, Shanghai 201804
1 shared publication
Latest Publications
- 1 January 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (1)
Large eddy simulation assessment of an advanced perforated wall model for effusion cooling of gas turbine combustor
To accurately predict the effusion cooling process of a gas turbine combustor liner, a simplified heat and mass transfer model named the Advanced Perforated Wall Model (A-PWM) is developed, and turbulent flow and vortex dynamics are investigated using large eddy simulation (LES). The model is first validated for effusion cooling with a single cylindrical hole, and the prediction results match those of the conjugate heat transfer (CHT) model and experimental data. Due to the simplification of the physical cooling hole geometry, the LES-A-PWM reduces grid usage by 73% and improves computational efficiency by 62.55% compared to LES-CHT. It is also found that the local cooling effectiveness of LES-A-PWM shows deviations compared to experimental data, and LES-CHT results at the cooling hole outlet. Further analysis shows counter-rotating vortex pairs (CRVPs) form at the cooling hole outlet, enhancing mixing between cooling and hot flows and increasing Reynolds stress, thus affecting effusion cooling effectiveness. However, unlike resolved LES-CHT, the LES-A-PWM neglects the hole geometry and applies a uniform velocity, causing slight deviations near the outlet. Later, simulations on a combustor liner with 20 holes show that A-PWM agrees well with CHT and experimental data, maintaining deviations within 10%. The required mesh cells and computation time by LES-A-PWM are reduced by 35.8% and 35.9%, respectively. As the number of holes increases, turbulence interactions intensify between adjacent holes, while local heat transfer around the cooling jets weakens. These results demonstrate that A-PWM, assessed through LES, provides an accurate and efficient approach for design-level evaluation of combustor liner cooling.
- 1 January 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (1)
Large eddy simulation assessment of an advanced perforated wall model for effusion cooling of gas turbine combustor
To accurately predict the effusion cooling process of a gas turbine combustor liner, a simplified heat and mass transfer model named the Advanced Perforated Wall Model (A-PWM) is developed, and turbulent flow and vortex dynamics are investigated using large eddy simulation (LES). The model is first validated for effusion cooling with a single cylindrical hole, and the prediction results match those of the conjugate heat transfer (CHT) model and experimental data. Due to the simplification of the physical cooling hole geometry, the LES-A-PWM reduces grid usage by 73% and improves computational efficiency by 62.55% compared to LES-CHT. It is also found that the local cooling effectiveness of LES-A-PWM shows deviations compared to experimental data, and LES-CHT results at the cooling hole outlet. Further analysis shows counter-rotating vortex pairs (CRVPs) form at the cooling hole outlet, enhancing mixing between cooling and hot flows and increasing Reynolds stress, thus affecting effusion cooling effectiveness. However, unlike resolved LES-CHT, the LES-A-PWM neglects the hole geometry and applies a uniform velocity, causing slight deviations near the outlet. Later, simulations on a combustor liner with 20 holes show that A-PWM agrees well with CHT and experimental data, maintaining deviations within 10%. The required mesh cells and computation time by LES-A-PWM are reduced by 35.8% and 35.9%, respectively. As the number of holes increases, turbulence interactions intensify between adjacent holes, while local heat transfer around the cooling jets weakens. These results demonstrate that A-PWM, assessed through LES, provides an accurate and efficient approach for design-level evaluation of combustor liner cooling.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Numerical investigations on hydrogen-enriched fuel–air mixing characteristics in a single micromix nozzle for the gas turbine combustor
Efficient hydrogen-enriched fuel–air mixing in a micromix combustor is a key factor that influences the combustion process, flow dynamics, and NOx formation. This study focuses on a single nozzle within a hydrogen-enriched micromix combustor to identify optimal fuel–air mixing strategies and explore the mixing mechanism. Through detailed numerical investigations of gas flow and geometric parameters by Reynolds-averaged Navier–Stoke and large eddy simulation, the influence on the cold-flow field and mixing performance is analyzed. The results indicate that the momentum ratio significantly affects the initial jet trajectory and vorticity magnitude; an optimal momentum ratio of approximately 30 yielded the best mixing characteristics. Preheating the air to 575 K was observed to increase turbulent viscosity and molecular kinetic energy, thereby promoting more effective momentum and mass diffusion rates. Increasing the number of fuel tubes and reducing the tube diameter expanded the diffusion region, improving hydrogen-enriched fuel–air interaction. In addition, higher mass flow rates resulted in deeper jet penetration, while the jet angle significantly influenced the spatial fuel distribution and vortex structure within the premixing tube. A properly adjusted jet angle of 30° led to the breakdown of large vortices into smaller structures, thereby maximizing the contact surface between hydrogen-enriched fuel and air and, thus, enhancing the mixing characteristics. Overall, the micromix combustor demonstrates strong potential for achieving efficient, small-scale fuel–air mixing, which is essential for clean, low-emission combustion.
- 1 September 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (9)
Numerical investigations on hydrogen-enriched fuel–air mixing characteristics in a single micromix nozzle for the gas turbine combustor
Efficient hydrogen-enriched fuel–air mixing in a micromix combustor is a key factor that influences the combustion process, flow dynamics, and NOx formation. This study focuses on a single nozzle within a hydrogen-enriched micromix combustor to identify optimal fuel–air mixing strategies and explore the mixing mechanism. Through detailed numerical investigations of gas flow and geometric parameters by Reynolds-averaged Navier–Stoke and large eddy simulation, the influence on the cold-flow field and mixing performance is analyzed. The results indicate that the momentum ratio significantly affects the initial jet trajectory and vorticity magnitude; an optimal momentum ratio of approximately 30 yielded the best mixing characteristics. Preheating the air to 575 K was observed to increase turbulent viscosity and molecular kinetic energy, thereby promoting more effective momentum and mass diffusion rates. Increasing the number of fuel tubes and reducing the tube diameter expanded the diffusion region, improving hydrogen-enriched fuel–air interaction. In addition, higher mass flow rates resulted in deeper jet penetration, while the jet angle significantly influenced the spatial fuel distribution and vortex structure within the premixing tube. A properly adjusted jet angle of 30° led to the breakdown of large vortices into smaller structures, thereby maximizing the contact surface between hydrogen-enriched fuel and air and, thus, enhancing the mixing characteristics. Overall, the micromix combustor demonstrates strong potential for achieving efficient, small-scale fuel–air mixing, which is essential for clean, low-emission combustion.