Jinkwan Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jinkwan Lee has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Keun-Soo Kim
Department of Electronic Materials Engineering, Hoseo University, Asan 31499, Republic of Korea
2 shared publications - Sang-Gyu Choi
Department of Materials Science and Engineering, Inha University, Incheon 22212, Republic of Korea
2 shared publications - Sangwook Kim
R&D Center, Lotus Materials Co., Ltd., Incheon 22212, Republic of Korea
2 shared publications - Soong-Keun Hyun
Department of Materials Science and Engineering, Inha University, Incheon 22212, Republic of Korea
2 shared publications Jae-Ho Shin
1 shared publicationKeun-Soo Kim
1 shared publication
Latest Publications
- Open Access
- 21 November 2025
- Published by Elsevier in Results in Materials
- Vol. 28
Effect of pore structure on void formation in lotus type porous Cu/solder joints
- 21 November 2025
- Published by Elsevier in Results in Materials
- Vol. 28
Open AccessEffect of pore structure on void formation in lotus type porous Cu/solder joints
- Open Access
- 27 October 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (11) , 352
Optimization of Direct Bonding Process for Lotus-Type Porous Copper to Alumina Substrates
The effects of processing conditions and holding time on the direct bonding (DBC) of lotus-type porous copper to alumina substrates were systematically investigated. The evolution of copper morphology and the resulting shear strength were evaluated under varying pressures (0.3–0.6 Torr) and bonding durations (5–160 min) at a fixed bonding temperature. It was found that pressure within the tested range exerted a negligible influence on joint quality, as direct bonding occurred consistently. In contrast, holding time was found to be a critical factor: a duration of 10 min yielded optimal bonding with high shear strength while preserving the porous structure, whereas shorter times led to incomplete bonding, and longer times caused structural collapse due to liquid-phase flow. The oxidation behavior, governed by parabolic growth kinetics, was identified as the primary mechanism controlling morphological evolution. These findings provide practical guidance for optimizing DBC bonding of porous copper in power semiconductor applications, balancing joint strength and structural integrity.
- 27 October 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (11) , 352
Open AccessOptimization of Direct Bonding Process for Lotus-Type Porous Copper to Alumina Substrates
The effects of processing conditions and holding time on the direct bonding (DBC) of lotus-type porous copper to alumina substrates were systematically investigated. The evolution of copper morphology and the resulting shear strength were evaluated under varying pressures (0.3–0.6 Torr) and bonding durations (5–160 min) at a fixed bonding temperature. It was found that pressure within the tested range exerted a negligible influence on joint quality, as direct bonding occurred consistently. In contrast, holding time was found to be a critical factor: a duration of 10 min yielded optimal bonding with high shear strength while preserving the porous structure, whereas shorter times led to incomplete bonding, and longer times caused structural collapse due to liquid-phase flow. The oxidation behavior, governed by parabolic growth kinetics, was identified as the primary mechanism controlling morphological evolution. These findings provide practical guidance for optimizing DBC bonding of porous copper in power semiconductor applications, balancing joint strength and structural integrity.
- Open Access
Predictive Modeling of Shear Strength for Lotus-Type Porous Copper Bonded to Alumina
This study investigates the shear strength of lotus-type unidirectional porous copper bonded to alumina substrates using the Direct Bonded Copper (DBC) process. Porous copper specimens with various porosities (38.7–50.9%) and pore sizes (150–800 μm) were fabricated and joined to alumina discs. Shear testing revealed that both porosity and pore size significantly affect the interfacial strength. While higher porosity led to reduced shear strength, larger pore sizes enhanced the maximum shear strength owing to increased local contact areas and crack coalescence in the alumina substrate. Fractographic analysis using optical microscopy and SEM-EDS confirmed that failure mainly occurred in the alumina, with local fracture associated with pore distribution and size. To improve strength prediction, a modified model was proposed, reducing the error from 12.3% to 7.5% and increasing the coefficient of determination (R2) from 0.43 to 0.74. These findings highlight the necessity of considering both porosity and pore size when predicting the shear strength of porous copper/alumina DBC joints, and they provide important insights for optimizing metal structures in metal–ceramic bonding for high-performance applications.
Open AccessPredictive Modeling of Shear Strength for Lotus-Type Porous Copper Bonded to Alumina
This study investigates the shear strength of lotus-type unidirectional porous copper bonded to alumina substrates using the Direct Bonded Copper (DBC) process. Porous copper specimens with various porosities (38.7–50.9%) and pore sizes (150–800 μm) were fabricated and joined to alumina discs. Shear testing revealed that both porosity and pore size significantly affect the interfacial strength. While higher porosity led to reduced shear strength, larger pore sizes enhanced the maximum shear strength owing to increased local contact areas and crack coalescence in the alumina substrate. Fractographic analysis using optical microscopy and SEM-EDS confirmed that failure mainly occurred in the alumina, with local fracture associated with pore distribution and size. To improve strength prediction, a modified model was proposed, reducing the error from 12.3% to 7.5% and increasing the coefficient of determination (R2) from 0.43 to 0.74. These findings highlight the necessity of considering both porosity and pore size when predicting the shear strength of porous copper/alumina DBC joints, and they provide important insights for optimizing metal structures in metal–ceramic bonding for high-performance applications.