Borvorn Israngkura Na Ayudhya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Borvorn Israngkura Na Ayudhya has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
Rada Klingsad
Department of Civil Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Pathum Thani 12110
3 shared publicationsMasahiko Kunishima
Technical Advisor, Research Organization for Regional Alliance, Kochi University of Technology, Tosayamada-cho, Kami-city, Kochi, 782-0003, Japan
1 shared publication
Latest Publications
- Open Access
- 1 December 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (12) , 5356-5381
Influence of Polypropylene Fiber on Mechanical and Shrinkage Behavior of Porcelain Based Geopolymer
This study examines the effects of polypropylene (PP) fiber content and initial curing temperature on shrinkages, mechanical properties, and microstructural characteristics of porcelain-based geopolymers. Geopolymer mixes were prepared with PP fiber dosages of 0.5%, 1.0%, 1.5%, and 2.0% by weight and initially cured at 60 °C, 75 °C, 90 °C, and 105 °C. Autogenous and drying shrinkage were monitored at 24 h, 72 h and 3, 7, 14, 21, 28, 60, 90, and 120 days, while compressive and splitting tensile strengths were tested at 3, 7, 14, 21, and 28 days. The results demonstrated that the incorporation of PP fiber not only shortened the setting time but also significantly reduced both autogenous and drying shrinkage of the geopolymer mortar. The most favorable performance was observed in specimens containing 2.0% PP fiber cured at 105 °C, which exhibited the lowest shrinkage values. Autogenous shrinkage was 439 μɛ at 24 h and 392 μɛ at 120 days, while drying shrinkage was 544 μɛ at 24 h and 194 μɛ at 120 days. Increasing fiber content decreased porosity, producing a more compact, homogeneous matrix and improving mechanical performance of concrete specimens, particularly splitting tensile strength; the optimal dosage was 2%, yielding 28‑day compressive strength of 41.03 N/mm² and splitting tensile strength of 7.65 N/mm².
- 1 December 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (12) , 5356-5381
Open AccessInfluence of Polypropylene Fiber on Mechanical and Shrinkage Behavior of Porcelain Based Geopolymer
This study examines the effects of polypropylene (PP) fiber content and initial curing temperature on shrinkages, mechanical properties, and microstructural characteristics of porcelain-based geopolymers. Geopolymer mixes were prepared with PP fiber dosages of 0.5%, 1.0%, 1.5%, and 2.0% by weight and initially cured at 60 °C, 75 °C, 90 °C, and 105 °C. Autogenous and drying shrinkage were monitored at 24 h, 72 h and 3, 7, 14, 21, 28, 60, 90, and 120 days, while compressive and splitting tensile strengths were tested at 3, 7, 14, 21, and 28 days. The results demonstrated that the incorporation of PP fiber not only shortened the setting time but also significantly reduced both autogenous and drying shrinkage of the geopolymer mortar. The most favorable performance was observed in specimens containing 2.0% PP fiber cured at 105 °C, which exhibited the lowest shrinkage values. Autogenous shrinkage was 439 μɛ at 24 h and 392 μɛ at 120 days, while drying shrinkage was 544 μɛ at 24 h and 194 μɛ at 120 days. Increasing fiber content decreased porosity, producing a more compact, homogeneous matrix and improving mechanical performance of concrete specimens, particularly splitting tensile strength; the optimal dosage was 2%, yielding 28‑day compressive strength of 41.03 N/mm² and splitting tensile strength of 7.65 N/mm².
- 1 November 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (11) , 4655-4676
Shrinkage Characteristics and Abrasion Resistance of Porcelain Waste-Based Geopolymers Mortar Under Chemical Exposure
This study investigated microstructural analyses, dry shrinkage, and autogenous shrinkage of mortar using defective sanitary ware porcelain as a low-calcium material with sodium hydroxide (NaOH) and sodium silicate (Na₂SiO₃). Additionally, the abrasive resistance of concrete was examined under chemical corrosion environments of 5%, 10%, 15%, and 20% H₂SO₄, HCl, and MgSO₄. The microstructural analyses using XRF, DTA-TGA, and SEM were conducted at 28 days. For specimen preparation, mortar specimens were oven-cured for 2 h at 105°C, while concrete specimens were oven-cured for 24 h and air-cured for 28 days before undergoing chemical immersion at 3, 7, 14, 21, 28, 60, and 90 days. NaOH concentrations of 8, 10, 12, and 14 Molar (M) were used. The results indicated that shrinkage in porcelain-based geopolymer mortars increased with higher NaOH concentration, and increasing the initial curing temperature led to increased mortar shrinkage. The autogenous shrinkage of 14M alkali-activated porcelain mortar was found to be higher than that of 8M, 10M, and 12M NaOH concentration mortars. Additionally, increasing the NaOH concentration reduced the abrasive resistance of the concrete. The maximum weight loss values were 8.21%, 6.91%, and 0.96% for 20% H₂SO₄ (90 days immersion), HCl (90 days immersion), and 20% MgSO₄ (90 days immersion), respectively. The microstructural findings confirmed the formation of gel-intact phases, highlighting the importance of curing time and NaOH concentration in low-calcium binder material. This study emphasized the critical role of curing temperature in optimizing the mechanical and durability properties of defective sanitary ware porcelain-based geopolymer.
- 1 November 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (11) , 4655-4676
Shrinkage Characteristics and Abrasion Resistance of Porcelain Waste-Based Geopolymers Mortar Under Chemical Exposure
This study investigated microstructural analyses, dry shrinkage, and autogenous shrinkage of mortar using defective sanitary ware porcelain as a low-calcium material with sodium hydroxide (NaOH) and sodium silicate (Na₂SiO₃). Additionally, the abrasive resistance of concrete was examined under chemical corrosion environments of 5%, 10%, 15%, and 20% H₂SO₄, HCl, and MgSO₄. The microstructural analyses using XRF, DTA-TGA, and SEM were conducted at 28 days. For specimen preparation, mortar specimens were oven-cured for 2 h at 105°C, while concrete specimens were oven-cured for 24 h and air-cured for 28 days before undergoing chemical immersion at 3, 7, 14, 21, 28, 60, and 90 days. NaOH concentrations of 8, 10, 12, and 14 Molar (M) were used. The results indicated that shrinkage in porcelain-based geopolymer mortars increased with higher NaOH concentration, and increasing the initial curing temperature led to increased mortar shrinkage. The autogenous shrinkage of 14M alkali-activated porcelain mortar was found to be higher than that of 8M, 10M, and 12M NaOH concentration mortars. Additionally, increasing the NaOH concentration reduced the abrasive resistance of the concrete. The maximum weight loss values were 8.21%, 6.91%, and 0.96% for 20% H₂SO₄ (90 days immersion), HCl (90 days immersion), and 20% MgSO₄ (90 days immersion), respectively. The microstructural findings confirmed the formation of gel-intact phases, highlighting the importance of curing time and NaOH concentration in low-calcium binder material. This study emphasized the critical role of curing temperature in optimizing the mechanical and durability properties of defective sanitary ware porcelain-based geopolymer.
- Open Access
- 1 August 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (8) , 3223-3244
Effects of H₂SO₄, HCl, and MgSO₄ Attack on Porcelain-Based Geopolymer Concrete
This study examined the durability of porcelain-based geopolymer concrete when exposed to strong acids, chlorides, and sulfates. Specimens prepared with a 14M NaOH solution and initially cured at 105°C for 24 hours were submerged in acidic and alkaline solutions for varying durations—3, 7, 14, 21, 28, 60, and 90 days. Compressive and splitting tensile strength tests were conducted to assess material performance. The results showed that immersion in H₂SO₄, HCl, and MgSO₄ solutions led to weight loss and reductions in both compressive and splitting tensile strengths. Strength deterioration was more pronounced in the early stages, with a peak weight loss rate of 15.32 g/day. After 90 days in 20% H₂SO₄, 20% HCl, and 20% MgSO₄ solutions, the residual compressive strengths were measured at 2.80, 14.19, and 3.29 N/mm², respectively, while splitting tensile strengths were recorded at 0.40, 1.21, and 0.51 N/mm². The ratio of splitting tensile strength to compressive strength (fsp/f’c) was influenced by molar concentration and immersion duration. Experimental findings revealed that a high molarity NaOH solution and elevated curing temperature enhanced resistance to HCl attack more effectively than H₂SO₄ and MgSO₄. Moreover, the experimental data closely aligned with the ACI 318 design code, though it tended to overestimate tensile strength.
- 1 August 2025
- Published by Ital Publication in Civil Engineering Journal
- Vol. 11 (8) , 3223-3244
Open AccessEffects of H₂SO₄, HCl, and MgSO₄ Attack on Porcelain-Based Geopolymer Concrete
This study examined the durability of porcelain-based geopolymer concrete when exposed to strong acids, chlorides, and sulfates. Specimens prepared with a 14M NaOH solution and initially cured at 105°C for 24 hours were submerged in acidic and alkaline solutions for varying durations—3, 7, 14, 21, 28, 60, and 90 days. Compressive and splitting tensile strength tests were conducted to assess material performance. The results showed that immersion in H₂SO₄, HCl, and MgSO₄ solutions led to weight loss and reductions in both compressive and splitting tensile strengths. Strength deterioration was more pronounced in the early stages, with a peak weight loss rate of 15.32 g/day. After 90 days in 20% H₂SO₄, 20% HCl, and 20% MgSO₄ solutions, the residual compressive strengths were measured at 2.80, 14.19, and 3.29 N/mm², respectively, while splitting tensile strengths were recorded at 0.40, 1.21, and 0.51 N/mm². The ratio of splitting tensile strength to compressive strength (fsp/f’c) was influenced by molar concentration and immersion duration. Experimental findings revealed that a high molarity NaOH solution and elevated curing temperature enhanced resistance to HCl attack more effectively than H₂SO₄ and MgSO₄. Moreover, the experimental data closely aligned with the ACI 318 design code, though it tended to overestimate tensile strength.
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia Computer Science
- Vol. 164, 407-413
Assessment of Risk Management for Small Residential Projects in Thailand
- 1 January 2019
- Published by Elsevier in Procedia Computer Science
- Vol. 164, 407-413
Open AccessAssessment of Risk Management for Small Residential Projects in Thailand