Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Elif Yurttas has a total of 22 co-authors. Here are the top co-authors by number of shared publications:

  • Nadir Ayrilmis

    Department of Wood Mechanics and Technology, Forestry Faculty, Istanbul University-Cerrahpasa, Bahcekoy, Sariyer, Istanbul 34473, Turkey

    5 shared publications
  • Ferhat Özdemir

    Department of Wood Chemistry and Technology, Faculty of Forestry, Kahramanmaras Sutcu Imam University, 46100, Kahramanmaras, Türkiye

    4 shared publications
  • Nadir Ayrilmis

    Department of Wood Mechanics and Technology, Faculty of Forestry, İstanbul University-Cerrahpaşa, İstanbul, Türkiye

    2 shared publications
  • Nurten Tetik

    Department of Food Engineering, Faculty of Chemistry and Metallurgy, Yıldız Technical University, Istanbul, Türkiye

    2 shared publications
  • Sivasubramanian Palanisamy

    Department of Mechanical Engineering, School of Engineering, Mohan Babu University, Tirupati-517102, Andhra Pradesh, India

    2 shared publications
  • Ali Durmus

    Department of Chemical Engineering, Faculty of Engineering, Istanbul University-Cerrahpasa, Istanbul, Turkey

    1 shared publication

Latest Publications

  • Open Access

    Thermal Performance of Silica-Coated Wood Particles

    by Elif Yurttaş, Mariem Zouari, Silvo Hribernik, Matthew Schwarzkopf

    Wood is one of the most widely used sustainable lignocellulosic materials, with numerous applications in consumer goods and the construction sector. Despite its positive properties, such as a high strength-to-weight ratio, thermal insulation, and low density, wood’s natural thermal degradation can limit its potential applications. In composite applications like wood–plastic composites, the particle morphology and surface topography must be preserved to support intimate polymer–wood contact and mechanical interlocking. This study investigated the efficacy of a thin silica coating for thermal protection, which was applied via an in situ sol–gel method using the precursor tetraethoxysilane (TEOS). The wood particles and treatments were characterized using particle size analysis, physisorption, FTIR, SEM, XRD, and TGA analyses. After treatment, the specific and microporous surface area of wood particles increased by 118% and 97%, respectively, an effect of the porosity of silica itself. FTIR spectra of the silica-treated wood displayed peaks corresponding to Si stretching, and SEM micrographs confirmed a successful silica coating formation. TGA showed that the silica coating increased the temperatures needed to degrade the underlying hemicellulose and cellulose by 16 °C for all treatment levels. This particle-scale coating provided a promising method for producing thermally protected, functionalizable wood fillers for composites that maintain the filler geometry and potential mechanical interlocking, offering an attractive upcycling pathway for wood residues.


  • Properties of plastic composites filled with giant reed flour and magnesium oxide nanoparticles

    by Nadir Ayrilmis, Elif Yurttas, Esra Yildiz Avsar, Memet Vezir Kahraman, Ferhat Özdemir, Sivasubramanian Palanisamy, Ferhat Yetiş, Madhan Kumar Gurusamy, Saleh A Al-Farraj

    Wood plastic composites (WPCs) were produced from recycled polypropylene (RPP) matrix, giant reed (GR) flour, and magnesium oxide nanoparticles (nano-MgO). The physical, mechanical, and thermal properties were analyzed. Different amounts of GR flour from 10 wt% to 40 wt%, and nano-MgO from 1.0 wt% to 2 wt% were added into the RPP matrix. The water resistance, mechanical, and thermal properties of the injection molded WPCs were determined according to the ISO standards. The bending and tensile modulus of the WPCs were considerably enhanced with the addition of the GR flour up to 40 wt%, while this was found to be maximum at 30 wt% for the bending and tensile strengths. The water absorption of the WPCs increased with the addition of the GR flour, as expected. The results of thermal analysis revealed that the addition of the GR flour increased the thermal stability of the WPCs, especially the degree of crystallization and the melting enthalpies of the RPP matrix, due to the good adhesion between the GR flour and the RPP. The incorporation of the nano-MgO affected adversely the mechanical properties of the WPCs. Lower thermal stability was observed for WPCs containing nano-MgO. The inclusion of 30 wt% GR flour in the RPP matrix gave the best mechanical and thermal properties.


  • Antibacterial performance of biodegradable polymer and hazelnut husk flour antibacterial biofilm with silver nanoparticles

    by Nadir Ayrilmis, Elif Yurttas, Nurten Tetik, Ferhat Özdemir, Sivasubramanian Palanisamy, Aravindhan Alagarsamy, Siva Ramasamy, Mika Sillanpää, Saleh A . Al-Farraj

    The antibacterial performance of biocomposite films prepared from lignocellulosic waste (hazelnut husk or hazelnut leafy green cover) modified with silver nanoparticles and polylactic acid (PLA) was determined. The amount of hazelnut husk in the PLA matrix ranged from 10 to 40% by weight in 10% increments. The composite pellets were produced using a twin-screw extruder. Biocomposite films of 0.6 mm x 40 mm x 200 mm were produced from the pellets in a laboratory hydraulic hot press. The surfaces of the modified hazelnut husk and biocomposite specimens were analyzed by scanning electron microscopy (SEM) and inductively coupled plasma optical emission spectrometry (ICP-OES). The antibacterial activity of the biocomposite films against Staphylococcus aureus bacteria was determined using the ASTM E 2149 (2020) method. The antibacterial activity of the biocomposite films increased noticeably with the addition of hazelnut husk modified with the silver nanoparticles. Compared to the pure PLA film, the biocomposite films with 10 wt% modified husk flour showed the lowest antibacterial activity (31.3%) against S. aureus over 24-h while the films with 40 wt% showed the highest antibacterial activity (99.9%). The biocomposite films made of hazelnut husk flour with silver nanoparticles and PLA matrix could be considered for food packaging applications.


  • Open Access

    Mechanical and Thermal Properties of 3D‐Printed Biocomposites of Polylactic Acid and Thermally Modified Wood Flour with Silver Nanoparticles

    by Elif Yurttas, Nadir Ayrilmis

    This study investigates the effects of thermal treatment and silver nanoparticles on the mechanical and thermal properties of additively manufactured wood/polylactic acid (PLA) specimens. The 5 and 10 wt% additions of the wood flour into the PLA matrix are done in the twin screw extruder. The test specimens are produced from the filaments with a diameter of 1.75 mm using 3D printer. The mechanical properties of the 3D‐printed wood/PLA specimens are affected by the wood flour content, thermal treatment of wood, and silver nanoparticles. The 3D‐printed neat PLA specimens have better mechanical properties than the wood flour‐filled PLA specimens. The bending strength of the specimens enhances with increasing wood flour content while the tensile strength decreases. The increases in the mechanical properties reveal that the thermal treatment of the wood improves the compatibility between wood and PLA matrix, which hereby improves the interfacial adhesion. The addition of the silver nanoparticles positively affects the mechanical properties and it is more compatible with thermally modified wood particles as compared to the untreated wood particles.


  • Antimicrobial properties of 3D printed biocomposites with heat-treated wood flour using silver nanoparticles with leaf extract

    by Elif Yurttas, Nurten Tetik, Nadir Ayrilmis

    Increasing environmental concerns have increased interest in the development of biodegradable materials. In this study, biofilaments for 3D printing were produced with biodegradable polylactic acid (PLA) matrix and modified using wood flour which Liquidambar orientalis leaf extract green synthesized reducing silver nanoparticles and aqueous silver nanoparticles and these filaments are 3D printed. The wood flour and the biocomposite 3D printed were characterized by inductively coupled plasma-optical emission spectrometry (ICP-OES) Analysis and Scanning electron microscope (SEM) techniques. In the antimicrobial test, it was determined that the biocomposites showed antibacterial activity against Escherichia coli ATCC 25922 and Staphylococcus aureus ATCC 6538, and the antifungal activity against Candida albicans ATCC 10231, Aspergillus niger ATCC 627. All the biocomposites containing the silver nitrate nanoparticles clearly exhibited the antibacterial properties. The resulting biocomposites were very suitable for biomedical and food industrial applications.


  • Mechanical and thermal properties of biocomposite films produced from hazelnut husk and polylactic acid

    by Ferhat Özdemir, Nadir Ayrilmis, Elif Yurttaş

    This study focused on the potential use of hazelnut husk (HH) flour, agricultural by-product, as filler in the PLA biocomposite films. The tensile strength and elongation at break of the biocomposites films decreased with the increasing content of the HH flour. As the amount of the HH flour in the PLA was increased by 10 wt%, the tensile strength decreased from 33 to 26.3 MPa. A sharp decrease in the tensile strength (6.33 MPa) of the specimens was determined as the amount of the HH flour was increased by 20 wt%. There was no significant difference in the tensile strength as the HH content increased from 20 to 40 wt%. The main reason for the lower tensile strength was mainly attributed to them due to the weak interfacial bond between HH flour with higher polar surface and the PLA with lower polar surface. The hydrophilic nature of the HH leads to a tendency for HH fibers to mingle or form agglomerations, which resulted in the lower tensile strength, especially at high HH filler loadings. The increase in the filler content improved the thermal stability of biocomposites.


  • Properties of Biocomposite Films From PLA and Thermally Treated Wood Modified with Silver Nanoparticles Using Leaf Extracts of Oriental Sweetgum

    by Nadir Ayrilmis, Elif Yurttaş, Ali Durmus, Ferhat Özdemir, Rajini Nagarajan, Mayandi Kalimuthu, Manja Kitek Kuzman


  • Effects of core layer fiber size and face-to-core layer ratio on the properties of three-layered fiberboard

    by Nadir Ayrilmis, Turgay Akbulut, Elif Yurttaş

    The objective of this study was to transfer benefits of three-layered particleboards to medium density fiberboard (MDF) manufacture by using coarse fibers and, thus use less energy and lower-cost fibers as core layer material. In the first phase of this study, the effect of wood fiber size in the core layer on the properties of MDF was investigated. In the second phase, the effect of surface to core layer ratio (30/70, 40/60, 50/50, 60/40, and 70/30) on the properties of the MDF was investigated. The surface layers of the panels consisted of fine fibers. The wood fibers were produced using a thermo-mechanical refining process. The length and thickness of the fibers considerably increased with increasing defibrator discs distance. The 24-h TS values of the MDF specimens decreased from 36.8 to 34.2% as the fiber length in the core layer was increased from 4.3 to 11.5 mm. However, further increases in the fiber length increased TS values. Similarly, the bending strength, bending modulus, and internal bond strength increased with increasing fiber length (up to 11.5 mm) and thickness (up to 0.73 mm). The bending properties of the MDF specimens improved with increasing surface layer ratio, while the internal bond strength decreased.