Elodie Kaeshammer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Elodie Kaeshammer has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- A. Lefrançois
CEA, DAM, GRAMAT 1 , BP 80200, F-46500 Gramat
1 shared publication - François Willot
Centre de Morphologie Mathématique
1 shared publication - G. Lefrère
CEA, DAM, GRAMAT 1 , BP 80200, F-46500 Gramat
1 shared publication - J.-M. Goujon
CNRS, Institut FOTON, Université de Rennes 2 , UMR 6082, F-22305 Lannion
1 shared publication L. Borne
French-German Research Institute of Saint-Louis (ISL), Saint-Louis Cedex, France
1 shared publication- Luiz Poffo
CNRS, Institut FOTON, Université de Rennes 2 , UMR 6082, F-22305 Lannion
1 shared publication
Latest Publications
- 4 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Etude expérimentale et numérique de la sensibilité de compositions énergétiques ˸ influence de la microstructure et rôle de l'endommagement
La sensibilité au choc d’un matériau énergétique est liée à sa microstructure. L’onde de choc interagit avec la microstructure en créant des sauts de pression et des hausses de température localisés que l’on appelle points chauds. Ces points chauds sont de potentiels sites d’initiation de la détonation. L’objectif de thèse est d’étudier l’influence de différents paramètres microstructuraux sur la sensibilité au choc d’un matériau énergétique. Dans un premier temps, les microtomographies de trois matériaux RDX/Cire (70/30 en masse) sont étudiées. Ces trois matériaux sont identiques en termes de composition mais diffèrent par leur microstructure ainsi que par leur seuil d’amorçage en détonation. Les microtomographies sont filtrées et segmentées avant d’être caractérisées. La caractérisation permet d’identifier et de quantifier les différences de granulométries, distributions spatiale, formes des grains, points de contact entre les grains et réponses élastiques des 3 matériaux. Chaque grain labellisé est ensuite étudié individuellement (volume, surface, rayon moyen, sphéricité, convexité, angularité) et extrait pour former une bibliothèque de grains. Les résultats d’analyse d’images sont comparés avec des mesures expérimentales pour vérifier la validité de l’outil de segmentation mis en œuvre. Dans un second temps, des microstructures virtuelles sont générées à partir de la bibliothèque de grains réels afin de contrôler les caractéristiques des grains présents dans le matériau virtuel et d’isoler les effets de différents paramètres microstructuraux, tout en respectant la granulométrie et la distribution spatiale du matériau réel. Des simulations numériques dynamiques ont mis en évidence le rôle des défauts intra-granulaires ainsi que des points de contact entre les grains dans la localisation des contraintes et la formation de points chauds. L’importance des points de contact entre les grains était déjà pressentie à la suite de calculs FFT élastique quasi statique. Parallèlement à ce travail numérique, des expériences de récupération sous choc ont été mises au point et réalisées à l’ISL. Les échantillons endommagés sont microtomographiés. Les premières observations visuelles révèlent d’importantes fissurations et décohésions pour des pressions de choc bien inférieures au seuil d’amorçage de la détonation
- 4 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Etude expérimentale et numérique de la sensibilité de compositions énergétiques ˸ influence de la microstructure et rôle de l'endommagement
La sensibilité au choc d’un matériau énergétique est liée à sa microstructure. L’onde de choc interagit avec la microstructure en créant des sauts de pression et des hausses de température localisés que l’on appelle points chauds. Ces points chauds sont de potentiels sites d’initiation de la détonation. L’objectif de thèse est d’étudier l’influence de différents paramètres microstructuraux sur la sensibilité au choc d’un matériau énergétique. Dans un premier temps, les microtomographies de trois matériaux RDX/Cire (70/30 en masse) sont étudiées. Ces trois matériaux sont identiques en termes de composition mais diffèrent par leur microstructure ainsi que par leur seuil d’amorçage en détonation. Les microtomographies sont filtrées et segmentées avant d’être caractérisées. La caractérisation permet d’identifier et de quantifier les différences de granulométries, distributions spatiale, formes des grains, points de contact entre les grains et réponses élastiques des 3 matériaux. Chaque grain labellisé est ensuite étudié individuellement (volume, surface, rayon moyen, sphéricité, convexité, angularité) et extrait pour former une bibliothèque de grains. Les résultats d’analyse d’images sont comparés avec des mesures expérimentales pour vérifier la validité de l’outil de segmentation mis en œuvre. Dans un second temps, des microstructures virtuelles sont générées à partir de la bibliothèque de grains réels afin de contrôler les caractéristiques des grains présents dans le matériau virtuel et d’isoler les effets de différents paramètres microstructuraux, tout en respectant la granulométrie et la distribution spatiale du matériau réel. Des simulations numériques dynamiques ont mis en évidence le rôle des défauts intra-granulaires ainsi que des points de contact entre les grains dans la localisation des contraintes et la formation de points chauds. L’importance des points de contact entre les grains était déjà pressentie à la suite de calculs FFT élastique quasi statique. Parallèlement à ce travail numérique, des expériences de récupération sous choc ont été mises au point et réalisées à l’ISL. Les échantillons endommagés sont microtomographiés. Les premières observations visuelles révèlent d’importantes fissurations et décohésions pour des pressions de choc bien inférieures au seuil d’amorçage de la détonation
- Open Access
- 1 February 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Shock velocity measurement inside high density polyethylene using mid-infrared photonic Doppler velocimetry
Measuring shockwave velocity within a material is often beyond the capability of conventional photonic Doppler velocimetry (PDV) due to material opacity. This paper presents an experimental demonstration of shockwave measurement within high density polyethylene (HDPE) using a free-space photonic Doppler velocimeter operating in the 9–11 μm range (mid-infrared, Mid-IR). The shockwave is generated in HDPE by running a plate impact experiment with a gas launcher, inducing a refractive index change at the wave interface within the HDPE, and enabling partial reflection of the beam. The Mid-IR system is connected to the target by a hollow core fiber, which captures the reflected Mid-IR signal for velocity measurement. We measure the shock velocity within HDPE at 2600 m/s and record the beginning of particle velocity through the shocked HDPE near 500 m/s. A numerical simulation with OURANOS hydrocode shows good agreement with experimental results, despite edge effects and unperfected equation of state. These results confirm that Mid-IR PDV is an ideal candidate for material characterization under more extreme conditions such as detonation in energetic materials.
- 1 February 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Open AccessShock velocity measurement inside high density polyethylene using mid-infrared photonic Doppler velocimetry
Measuring shockwave velocity within a material is often beyond the capability of conventional photonic Doppler velocimetry (PDV) due to material opacity. This paper presents an experimental demonstration of shockwave measurement within high density polyethylene (HDPE) using a free-space photonic Doppler velocimeter operating in the 9–11 μm range (mid-infrared, Mid-IR). The shockwave is generated in HDPE by running a plate impact experiment with a gas launcher, inducing a refractive index change at the wave interface within the HDPE, and enabling partial reflection of the beam. The Mid-IR system is connected to the target by a hollow core fiber, which captures the reflected Mid-IR signal for velocity measurement. We measure the shock velocity within HDPE at 2600 m/s and record the beginning of particle velocity through the shocked HDPE near 500 m/s. A numerical simulation with OURANOS hydrocode shows good agreement with experimental results, despite edge effects and unperfected equation of state. These results confirm that Mid-IR PDV is an ideal candidate for material characterization under more extreme conditions such as detonation in energetic materials.
- Open Access
- 16 October 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (6) , 635-648
Dynamics simulations of RDX-based explosive materials during impact: role of the microstructure
The present work is a numerical investigation of the influence of different microstructural characteristics on the sensitivity to shock of energetic materials. We study three energetic materials that have the same composition in terms of weight fractions of their individual constituents (RDX and wax) but markedly different microstructures and shock sensitivity. Namely, the materials are made of grains with (i) smooth grain boundaries and intra-granular defects, (ii) sharp edges and few defects, and (iii) smooth grain boundaries and very few intra-granular defects. Making use of X-ray micro-computed tomography images of the materials, we first identify and quantify morphological differences in terms of grain size distribution, grain spatial distribution, grain shape, and contact points between grains. Second, we generate representative synthetic microstructures with realistic grain shapes and controlled morphological parameters based on the segmented images. We generate virtual granular materials in two and three dimensions, with and without pores, and with different grain shapes. Third, we carry out dynamic numerical simulations of shock wave propagation on various microstructure models. In all models, points of elevated temperature (hot spots) are observed along intra-granular defects and near contact points between grains. The histograms of the computed pressure field and temperature field (albeit to a lesser extent) show differences in the tails depending on the microstructure models representing the different materials. Numerical predictions are found to be in good agreement with experimental results: the VI-RDX-based material, which is the least sensitive to shock, has the fewest hot spots, while the RS-RDX-based and RVI-RDX-based materials have similar shock sensitivities and hot spot densities. The simulations emphasize a strong influence of intra-granular defects and contact points on the sensitivity to shock for these materials.
- 16 October 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (6) , 635-648
Open AccessDynamics simulations of RDX-based explosive materials during impact: role of the microstructure
The present work is a numerical investigation of the influence of different microstructural characteristics on the sensitivity to shock of energetic materials. We study three energetic materials that have the same composition in terms of weight fractions of their individual constituents (RDX and wax) but markedly different microstructures and shock sensitivity. Namely, the materials are made of grains with (i) smooth grain boundaries and intra-granular defects, (ii) sharp edges and few defects, and (iii) smooth grain boundaries and very few intra-granular defects. Making use of X-ray micro-computed tomography images of the materials, we first identify and quantify morphological differences in terms of grain size distribution, grain spatial distribution, grain shape, and contact points between grains. Second, we generate representative synthetic microstructures with realistic grain shapes and controlled morphological parameters based on the segmented images. We generate virtual granular materials in two and three dimensions, with and without pores, and with different grain shapes. Third, we carry out dynamic numerical simulations of shock wave propagation on various microstructure models. In all models, points of elevated temperature (hot spots) are observed along intra-granular defects and near contact points between grains. The histograms of the computed pressure field and temperature field (albeit to a lesser extent) show differences in the tails depending on the microstructure models representing the different materials. Numerical predictions are found to be in good agreement with experimental results: the VI-RDX-based material, which is the least sensitive to shock, has the fewest hot spots, while the RS-RDX-based and RVI-RDX-based materials have similar shock sensitivities and hot spot densities. The simulations emphasize a strong influence of intra-granular defects and contact points on the sensitivity to shock for these materials.