Samer Saleh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Samer Saleh has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Krish Thiagarajan
University of Massachusetts,Department of Mechanical Industrial Engineering,Amherst,USA
3 shared publicationsRichard Akers
3 shared publicationsBonjun Koo
Technip Energies , Houston, Texas, United States
2 shared publicationsAhmed AlShuwaykh
1 shared publicationAhmed Alshuwaykh
University of Massachusetts Amherst , Amherst, Massachusetts, United States
1 shared publication- Bonjun Koo1 shared publication
Latest Publications
- 8 October 2025
- Published by Elsevier in Ocean Engineering
- Vol. 342
Fatigue life assessment of nylon versus polyester mooring lines
- 8 October 2025
- Published by Elsevier in Ocean Engineering
- Vol. 342
Fatigue life assessment of nylon versus polyester mooring lines
- 23 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Smart Rope Technology for Aquaculture Farms - Low-Cost Conductive Yarns as Load and Strain Sensors for Integrity Monitoring
Blue Economy systems like marine energy and aquaculture farms consist of several individual units held by lines made of nylon or fiber ropes. Condition-monitoring of ropes and mooring lines are essential for the overall integrity of a marine energy farm. Our research is aimed at developing a low-cost prototype of a sensor integrated rope that can be used in long-term deployment for comprehensive monitoring purposes. A functional braided composite yarn with integrated electromagnetic properties was integrated into a 5 mm polypropylene rope. Samples with different conductor and core configurations were manufactured by Nautilus Defense. Data processing algorithms for receiving and processing information from the sensors were custom-made and tested at MITRE electronic laboratories. Mechanical tests were conducted at the Ocean Resources and Renewable Energy (ORRE) laboratory at UMass Amherst, where rope samples were subject to varying levels of static and dynamic forcing in dry conditions and under water. The observed linear trend of capacitance with strain offers strong potential for the sensor to support condition monitoring efforts of mooring lines for aquaculture and marine renewable energy.
- 23 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Smart Rope Technology for Aquaculture Farms - Low-Cost Conductive Yarns as Load and Strain Sensors for Integrity Monitoring
Blue Economy systems like marine energy and aquaculture farms consist of several individual units held by lines made of nylon or fiber ropes. Condition-monitoring of ropes and mooring lines are essential for the overall integrity of a marine energy farm. Our research is aimed at developing a low-cost prototype of a sensor integrated rope that can be used in long-term deployment for comprehensive monitoring purposes. A functional braided composite yarn with integrated electromagnetic properties was integrated into a 5 mm polypropylene rope. Samples with different conductor and core configurations were manufactured by Nautilus Defense. Data processing algorithms for receiving and processing information from the sensors were custom-made and tested at MITRE electronic laboratories. Mechanical tests were conducted at the Ocean Resources and Renewable Energy (ORRE) laboratory at UMass Amherst, where rope samples were subject to varying levels of static and dynamic forcing in dry conditions and under water. The observed linear trend of capacitance with strain offers strong potential for the sensor to support condition monitoring efforts of mooring lines for aquaculture and marine renewable energy.
- 18 December 2023
- Published by ASME International
Comparison of Fatigue Characteristics of Polyester and Nylon Mooring Lines for Shallow Water Floating Offshore Wind Turbines
The offshore wind industry is growing, and turbines with power production of 10 MW or greater are likely to become the norm in the future for both shallow and deep waters. For up to 50 m water depth, bottom fixed structures like monopiles and jackets are considered technically and economically feasible. Beyond this water depth, floating sub-structures offer the promise of cost reduction. Synthetic fiber ropes like nylon and polyester are good candidates for mooring system designs not only for their low cost, corrosion resistance, and fatigue life compared to steel wires and chains but also for their low stiffness which can reduce the wave frequency loads on the floater, especially in shallow water. In an IOWTC 2022 paper, the present authors discussed the strength characteristics of a shallow water mooring system comprising of chain-heavy chain-polyester-chain combination. This combination was specially chosen to work in shallow water conditions (60–100 m). Using simulations, the most probable maximum values of the mooring line were presented and discussed. In this paper, fatigue analysis has been performed on a similar mooring configuration wherein we consider two synthetic material options: polyester and nylon. The IEA 10 MW reference wind turbine and a semi-submersible floating platform were used in our simulation in Nantucket, MA (Water Depth (WD) = 60m). Three different design load cases DLC 1.2, DLC 6.1, and SLC I.1 were conducted in our simulations and the mooring line fatigue damages converted to represent 25-year service life. The analysis of mooring line tension-tension fatigue damage is calculated using the T-N curves. The fatigue damage is estimated using the built-in fatigue analysis toolbox in OrcaFlex after performing a set of OrcaFlex simulation files based on different mooring line configurations and design load cases. In this work, the behavior of nylon vs. polyester in shallow water hybrid mooring applications is investigated and discussed.
- 18 December 2023
- Published by ASME International
Comparison of Fatigue Characteristics of Polyester and Nylon Mooring Lines for Shallow Water Floating Offshore Wind Turbines
The offshore wind industry is growing, and turbines with power production of 10 MW or greater are likely to become the norm in the future for both shallow and deep waters. For up to 50 m water depth, bottom fixed structures like monopiles and jackets are considered technically and economically feasible. Beyond this water depth, floating sub-structures offer the promise of cost reduction. Synthetic fiber ropes like nylon and polyester are good candidates for mooring system designs not only for their low cost, corrosion resistance, and fatigue life compared to steel wires and chains but also for their low stiffness which can reduce the wave frequency loads on the floater, especially in shallow water. In an IOWTC 2022 paper, the present authors discussed the strength characteristics of a shallow water mooring system comprising of chain-heavy chain-polyester-chain combination. This combination was specially chosen to work in shallow water conditions (60–100 m). Using simulations, the most probable maximum values of the mooring line were presented and discussed. In this paper, fatigue analysis has been performed on a similar mooring configuration wherein we consider two synthetic material options: polyester and nylon. The IEA 10 MW reference wind turbine and a semi-submersible floating platform were used in our simulation in Nantucket, MA (Water Depth (WD) = 60m). Three different design load cases DLC 1.2, DLC 6.1, and SLC I.1 were conducted in our simulations and the mooring line fatigue damages converted to represent 25-year service life. The analysis of mooring line tension-tension fatigue damage is calculated using the T-N curves. The fatigue damage is estimated using the built-in fatigue analysis toolbox in OrcaFlex after performing a set of OrcaFlex simulation files based on different mooring line configurations and design load cases. In this work, the behavior of nylon vs. polyester in shallow water hybrid mooring applications is investigated and discussed.
- 7 December 2022
- Published by ASME International
Estimation of Most Probable Maximum Mooring Tensions for FOWT in Shallow Water US East Coast Environments
The US East Coast has several leased wind energy sites in water depths ranging from 60–100 m, where floating wind turbine systems are feasible. For these systems, designing suitable mooring systems for shallow water depths within the constraints of surviving hurricane conditions can be challenging. This study analyzed a mixed chain-synthetic mooring systems to predict the maximum extreme position and effective tension for different cases. Synthetic ropes, which offer a low cost and superior performance alternative compared to chain and wire ropes, were utilized dominantly in our mooring design. In this study, we simulated the IEA 10 MW reference wind turbine on a semi-submersible floating offshore structure deployed at two sites: Nantucket, MA (WD (Water Depth) = 60 m), and Monhegan, ME (WD = 100 m). For each depth and each mooring configuration, we conducted detailed numerical simulations for three different load design cases DLC 1.6 50-yr return period, DLC 6.1 50-yr return period, and SLC I.1 500-yr return period. The inflow turbulence was based on the Kaimal spectrum with the mean wind speed and turbulent intensity based on individual load cases and return periods. The JONSWAP spectrum was used to model waves with different significant heights and peak periods based on individual load cases. A uniform current was used for all simulation cases. For extreme value predictions, three 1-hour simulations with different seed numbers for the SLC I.1 500-yr return period were performed. The MPME (most probable maximum extreme) value is an extreme value statistic commonly used in the offshore industry. The top 10% of the peaks above a threshold value were further analyzed using a Weibull distribution to obtain MPME values. The effects of mooring material, number of lines per column and the water depth on the MPME as well as cost issues are discussed in the paper.
- 7 December 2022
- Published by ASME International
Estimation of Most Probable Maximum Mooring Tensions for FOWT in Shallow Water US East Coast Environments
The US East Coast has several leased wind energy sites in water depths ranging from 60–100 m, where floating wind turbine systems are feasible. For these systems, designing suitable mooring systems for shallow water depths within the constraints of surviving hurricane conditions can be challenging. This study analyzed a mixed chain-synthetic mooring systems to predict the maximum extreme position and effective tension for different cases. Synthetic ropes, which offer a low cost and superior performance alternative compared to chain and wire ropes, were utilized dominantly in our mooring design. In this study, we simulated the IEA 10 MW reference wind turbine on a semi-submersible floating offshore structure deployed at two sites: Nantucket, MA (WD (Water Depth) = 60 m), and Monhegan, ME (WD = 100 m). For each depth and each mooring configuration, we conducted detailed numerical simulations for three different load design cases DLC 1.6 50-yr return period, DLC 6.1 50-yr return period, and SLC I.1 500-yr return period. The inflow turbulence was based on the Kaimal spectrum with the mean wind speed and turbulent intensity based on individual load cases and return periods. The JONSWAP spectrum was used to model waves with different significant heights and peak periods based on individual load cases. A uniform current was used for all simulation cases. For extreme value predictions, three 1-hour simulations with different seed numbers for the SLC I.1 500-yr return period were performed. The MPME (most probable maximum extreme) value is an extreme value statistic commonly used in the offshore industry. The top 10% of the peaks above a threshold value were further analyzed using a Weibull distribution to obtain MPME values. The effects of mooring material, number of lines per column and the water depth on the MPME as well as cost issues are discussed in the paper.