Alexandra Schmuck
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexandra Schmuck has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Steven De Meester
Laboratory for Circular Process Engineering (LCPE), Department of Green Chemistry and Technology, Ghent University, Graaf Karel De Goedelaan 5, 8500 Kortrijk, Belgium
3 shared publications - Marcel C. P. van Eijk
NTCP, Duitslanddreef 7, 8447 SE Heerenveen, the Netherlands
2 shared publications Adeline Dupas
1 shared publication- Daniël Withoeck
Laboratory for Chemical Technology (LCT), Department of Materials, Textiles and Chemical Engineering, Faculty of Engineering and Architecture, Ghent University, Ghent, Belgium
1 shared publication - Dirk E. De Vos
KU Leuven
1 shared publication Hy Boui Chang
1 shared publication
Latest Publications
- Open Access
- 21 August 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 236
Balancing cost and quality: Multi-level modelling of sorting and pretreatment pathways for mixed plastic waste towards pyrolysis feedstock
- 21 August 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 236
Open AccessBalancing cost and quality: Multi-level modelling of sorting and pretreatment pathways for mixed plastic waste towards pyrolysis feedstock
- Open Access
- 3 June 2026
- Published by Springer Nature in Nature
- Vol. 654 (8118) , 383-390
Analysis of trade-offs of post-sorting plastic packaging
Increasing recycling rates requires not only better technologies but also smarter collection of plastic packaging waste1. Source separation—sorting materials such as plastics and metals at the household level—captures substantial waste volumes2,3, yet significant quantities still remain in the residual household waste fraction owing to misthrows and non-participation4,5. Post-sorting of mixed waste has been proposed as a one-bin alternative to boost capture6,7, despite concerns that contamination could compromise recycling quality7–9. Here we show, based on samples collected from one single material recovery facility, that bale purity, expressed as percent target polymer, is similar across source-separation and post-sorting pathways, but post-sorted bales contain more contaminants, including prohibited metals such as cadmium and lead. Post-sorted samples have higher moisture and dirt content8, which can lead to increased complex volatile organic compounds and necessitate additional washing. Concentrations of metals and halogens are elevated owing to non-packaging items, potentially compromising recycling quality and further complicating both mechanical and chemical recycling processes10,11. Although post-sorting can be a useful supplement, it should not replace source separation. Our results demonstrate that post-sorting can increase feedstock for recycling, but it also acts as a pathway for certain contaminants to enter plastic packaging waste, raising concentrations above typical levels, with potential risks to human health if these contaminants are not removed before recyclate production. As post-sorting of residual waste becomes crucial to meet circularity targets, these findings are particularly relevant.
- 3 June 2026
- Published by Springer Nature in Nature
- Vol. 654 (8118) , 383-390
Open AccessAnalysis of trade-offs of post-sorting plastic packaging
Increasing recycling rates requires not only better technologies but also smarter collection of plastic packaging waste1. Source separation—sorting materials such as plastics and metals at the household level—captures substantial waste volumes2,3, yet significant quantities still remain in the residual household waste fraction owing to misthrows and non-participation4,5. Post-sorting of mixed waste has been proposed as a one-bin alternative to boost capture6,7, despite concerns that contamination could compromise recycling quality7–9. Here we show, based on samples collected from one single material recovery facility, that bale purity, expressed as percent target polymer, is similar across source-separation and post-sorting pathways, but post-sorted bales contain more contaminants, including prohibited metals such as cadmium and lead. Post-sorted samples have higher moisture and dirt content8, which can lead to increased complex volatile organic compounds and necessitate additional washing. Concentrations of metals and halogens are elevated owing to non-packaging items, potentially compromising recycling quality and further complicating both mechanical and chemical recycling processes10,11. Although post-sorting can be a useful supplement, it should not replace source separation. Our results demonstrate that post-sorting can increase feedstock for recycling, but it also acts as a pathway for certain contaminants to enter plastic packaging waste, raising concentrations above typical levels, with potential risks to human health if these contaminants are not removed before recyclate production. As post-sorting of residual waste becomes crucial to meet circularity targets, these findings are particularly relevant.
- Open Access
- 27 January 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 228
Modelling material flows and cost-benefit of sorting PLA packaging waste in material recovery facilities under different market penetration scenarios
- 27 January 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 228
Open AccessModelling material flows and cost-benefit of sorting PLA packaging waste in material recovery facilities under different market penetration scenarios
- Open Access
- 23 October 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-9
Chemical valorization of waste polyacrylonitrile polymers via shuttle catalysis
Acrylonitrile-based polymers are widely used in industrial and consumer settings, contributing to the growing amount of plastic waste. Yet, their chemical recycling has largely been neglected, partly due to the potential release of harmful gases such as HCN and NOx. Herein, we report a catalytic process that enables valorization of the polymer’s N- and C-content, without releasing harmful nitrogen gases. Our strategy uses Pd-based shuttle catalysis to transfer HCN units from the polymer’s backbone to an olefin acceptor molecule, generating a carbonaceous polyolefin residue amenable to further upcycling, alongside a useful nitrile building block. The protocol can be optimized in two ways: to efficiently functionalize olefins and produce nitriles in up to quantitative yields as a safe, cost-effective alternative to commonly employed nitrile synthesis methods, and to fully dehydrocyanate polymers using ethylene as HCN acceptor. Furthermore, we demonstrate the applicability of our strategy for the upcycling of commercial polyacrylonitrile materials.
- 23 October 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-9
Open AccessChemical valorization of waste polyacrylonitrile polymers via shuttle catalysis
Acrylonitrile-based polymers are widely used in industrial and consumer settings, contributing to the growing amount of plastic waste. Yet, their chemical recycling has largely been neglected, partly due to the potential release of harmful gases such as HCN and NOx. Herein, we report a catalytic process that enables valorization of the polymer’s N- and C-content, without releasing harmful nitrogen gases. Our strategy uses Pd-based shuttle catalysis to transfer HCN units from the polymer’s backbone to an olefin acceptor molecule, generating a carbonaceous polyolefin residue amenable to further upcycling, alongside a useful nitrile building block. The protocol can be optimized in two ways: to efficiently functionalize olefins and produce nitriles in up to quantitative yields as a safe, cost-effective alternative to commonly employed nitrile synthesis methods, and to fully dehydrocyanate polymers using ethylene as HCN acceptor. Furthermore, we demonstrate the applicability of our strategy for the upcycling of commercial polyacrylonitrile materials.