Przemysław Woźniak
Research Subjects
Research Interests
Przemysław Woźniak has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jan Kindracki
Institute of Heat Engineering, Faculty of Power and Aeronautical Engineering, Warsaw University of Technology, Nowowiejska 21/25, 00-665 Warsaw, Poland
2 shared publications - Krzysztof Wacko
Faculty of Power and Aeronautical Engineering Institute of Heat Engineering Warsaw University of Technology Warsaw Poland
2 shared publications - Maciej Kołodziej2 shared publications
- Sylwia Kozłowska2 shared publications
- Łukasz Mężyk
Institute of Heat Engineering, Faculty of Power and Aeronautical Engineering, Warsaw University of Technology, Nowowiejska 21/25, 00-665 Warsaw, Poland
2 shared publications
Latest Publications
- 30 December 2024
- Published by Lukasiewicz Research Network - Institute of Industrial Organic Chemistry in Materiały Wysokoenergetyczne / High Energy Materials
- p. 89-98
Mobile stand for static rocket motor testing
This paper presents the design and study of solid propellant rocket motors using a mobile test stand. The test stand allows the measurement of two primary rocket motor parameters: combustion chamber pressure and thrust. In addition, the measurement system is structured so that measurements other than those previously mentioned can be defined and implemented by the user. Each experiment is recorded with an industrial surveillance cameras system and a high-speed digital camera synchronised with the other data acquisition channels. So far, tests have been conducted on two different calibres of motor, each acting as the main motor in the rocket test platform. The tests confirmed the functionality of the described stand and its flexibility in adapting to users’ requirements.
- 30 December 2024
- Published by Lukasiewicz Research Network - Institute of Industrial Organic Chemistry in Materiały Wysokoenergetyczne / High Energy Materials
- p. 89-98
Mobile stand for static rocket motor testing
This paper presents the design and study of solid propellant rocket motors using a mobile test stand. The test stand allows the measurement of two primary rocket motor parameters: combustion chamber pressure and thrust. In addition, the measurement system is structured so that measurements other than those previously mentioned can be defined and implemented by the user. Each experiment is recorded with an industrial surveillance cameras system and a high-speed digital camera synchronised with the other data acquisition channels. So far, tests have been conducted on two different calibres of motor, each acting as the main motor in the rocket test platform. The tests confirmed the functionality of the described stand and its flexibility in adapting to users’ requirements.
- 30 December 2024
- Published by Lukasiewicz Research Network - Institute of Industrial Organic Chemistry in Materiały Wysokoenergetyczne / High Energy Materials
- p. 55-64
The effect of using additive manufactured nozzle plugs on the ignition process
The selection of the nozzle plug and the appropriate quantity of an incendiary composition is an important step in modelling the ignition process of a solid propellant motor. The aim of the research discussed in this paper was to develop a nozzle plug which promotes adequate pressure in the combustor, while ensuring safety and simplicity of installation on the nozzle. The widespread availability of 3D printing technology has significantly simplified and reduced the cost of fabricating complex geometries. The authors designed and tested more than a dozen different snap-on nozzle plugs in order to investigate the effects of the material, the direction of printing, the shape and numer of snaps, the smoothness of the printed surface, the composition of the incendiary composition and the use of an additional hold-down feature. Tests were carried out on two test rigs equipped with features imitating a rocket motor nozzle, pressure measurement, temperature measurement, and a propellant fixture. The tests showed that the printed nozzle plugs only allow effective ignition of the solid propellant with additional attachment features applied and an incendiary composition in the form of a mixture of black powder and smokeless powder. The research used a low-smoke propellant based on poly(glycidyl azide) for fuel and ammonium perchlorate as the oxidizer with the addition of octogen.
- 30 December 2024
- Published by Lukasiewicz Research Network - Institute of Industrial Organic Chemistry in Materiały Wysokoenergetyczne / High Energy Materials
- p. 55-64
The effect of using additive manufactured nozzle plugs on the ignition process
The selection of the nozzle plug and the appropriate quantity of an incendiary composition is an important step in modelling the ignition process of a solid propellant motor. The aim of the research discussed in this paper was to develop a nozzle plug which promotes adequate pressure in the combustor, while ensuring safety and simplicity of installation on the nozzle. The widespread availability of 3D printing technology has significantly simplified and reduced the cost of fabricating complex geometries. The authors designed and tested more than a dozen different snap-on nozzle plugs in order to investigate the effects of the material, the direction of printing, the shape and numer of snaps, the smoothness of the printed surface, the composition of the incendiary composition and the use of an additional hold-down feature. Tests were carried out on two test rigs equipped with features imitating a rocket motor nozzle, pressure measurement, temperature measurement, and a propellant fixture. The tests showed that the printed nozzle plugs only allow effective ignition of the solid propellant with additional attachment features applied and an incendiary composition in the form of a mixture of black powder and smokeless powder. The research used a low-smoke propellant based on poly(glycidyl azide) for fuel and ammonium perchlorate as the oxidizer with the addition of octogen.