Toshiyuki Fukahori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Toshiyuki Fukahori has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Artit Chingsungnoen
Excellence Center of Plasma Technology, Mahasarakham University, Maha Sarakham 44150, Thailand
2 shared publications - Kodchaporn Chinnarat
Department of Physics, Faculty of Science, Mahasarakham University, Maha Sarakham 44150, Thailand
2 shared publications - Yasuharu Ohgoe
Division of Electronic Information and Biomedical Engineering, Department of Science and Engineering, Tokyo Denki University, Ishizaka, Hatoyama 350-0394, Saitama, Japan
2 shared publications
Latest Publications
- Open Access
Effects of the Hydrogen-to-Nitrogen Ratio in Plasma Nitriding on the Surface Properties of Cold Work Tool Steels
This study systematically investigates the effect of hydrogen flow rate (100, 200, 300, and 400 sccm) on the properties of DC53 steel during a 4 h plasma nitriding process conducted at 400 °C in an asymmetric bipolar pulsed reactor. A comprehensive characterisation approach was employed. X-ray diffraction (XRD) was used to identify the phase composition, revealing the formation of a compound layer consisting of ε-Fe2–3N (identified by its (100), (101), and (102) planes) and γ’-Fe4N (identified by its (220) plane). Mechanical properties were assessed using Vickers microhardness for surface measurements and nanoindentation for depth profiling. Glow discharge optical emission spectroscopy (GD-OES) provided elemental depth analysis, while a ball-on-disk tribometer evaluated the tribological performance. The optimal treatment was achieved at a hydrogen flow rate of 200 sccm. This condition yielded a peak surface hardness of 1121.5 ± 69.2 HV0.2. GD-OES analysis directly correlated this mechanical enhancement to a high surface nitrogen content of approximately 8.5% and an effective diffusion depth of about 50 µm.
Open AccessEffects of the Hydrogen-to-Nitrogen Ratio in Plasma Nitriding on the Surface Properties of Cold Work Tool Steels
This study systematically investigates the effect of hydrogen flow rate (100, 200, 300, and 400 sccm) on the properties of DC53 steel during a 4 h plasma nitriding process conducted at 400 °C in an asymmetric bipolar pulsed reactor. A comprehensive characterisation approach was employed. X-ray diffraction (XRD) was used to identify the phase composition, revealing the formation of a compound layer consisting of ε-Fe2–3N (identified by its (100), (101), and (102) planes) and γ’-Fe4N (identified by its (220) plane). Mechanical properties were assessed using Vickers microhardness for surface measurements and nanoindentation for depth profiling. Glow discharge optical emission spectroscopy (GD-OES) provided elemental depth analysis, while a ball-on-disk tribometer evaluated the tribological performance. The optimal treatment was achieved at a hydrogen flow rate of 200 sccm. This condition yielded a peak surface hardness of 1121.5 ± 69.2 HV0.2. GD-OES analysis directly correlated this mechanical enhancement to a high surface nitrogen content of approximately 8.5% and an effective diffusion depth of about 50 µm.
- Open Access
- 27 October 2025
- Published by MDPI AG in Preprints.org
Effects of the Hydrogen to Nitrogen Ratio in Plasma Nitriding on the Surface Properties of Cold Work Tool Steels
This study systematically investigates the effect of hydrogen flow rate (100, 200, 300, and 400 sccm) on the properties of DC53 steel during a 4-hour plasma nitriding process conducted at 400 °C in an asymmetric bipolar pulsed reactor. A comprehensive characterization approach was employed. X-ray diffraction (XRD) was used to identify the phase composition, revealing the formation of a compound layer consisting of ε-Fe2-3N (identified by its (100), (101), and (102) planes) and γ'-Fe4N (identified by its (220) plane). Mechanical properties were assessed using Vickers microhardness for surface measurements and nanoindentation for depth profiling. Glow discharge optical emission spectroscopy (GD-OES) provided elemental depth analysis, while a ball-on-disk tribometer evaluated the tribological performance. The optimal treatment was achieved at a hydrogen flow rate of 200 sccm. This condition yielded a peak surface hardness of 1121.5 ± 69.2 HV0.2. GD-OES analysis directly correlated this mechanical enhancement to a high surface nitrogen content of approximately 8.5% and an effective diffusion depth of about 50 µm.
- 27 October 2025
- Published by MDPI AG in Preprints.org
Open AccessEffects of the Hydrogen to Nitrogen Ratio in Plasma Nitriding on the Surface Properties of Cold Work Tool Steels
This study systematically investigates the effect of hydrogen flow rate (100, 200, 300, and 400 sccm) on the properties of DC53 steel during a 4-hour plasma nitriding process conducted at 400 °C in an asymmetric bipolar pulsed reactor. A comprehensive characterization approach was employed. X-ray diffraction (XRD) was used to identify the phase composition, revealing the formation of a compound layer consisting of ε-Fe2-3N (identified by its (100), (101), and (102) planes) and γ'-Fe4N (identified by its (220) plane). Mechanical properties were assessed using Vickers microhardness for surface measurements and nanoindentation for depth profiling. Glow discharge optical emission spectroscopy (GD-OES) provided elemental depth analysis, while a ball-on-disk tribometer evaluated the tribological performance. The optimal treatment was achieved at a hydrogen flow rate of 200 sccm. This condition yielded a peak surface hardness of 1121.5 ± 69.2 HV0.2. GD-OES analysis directly correlated this mechanical enhancement to a high surface nitrogen content of approximately 8.5% and an effective diffusion depth of about 50 µm.