Melba D’AStolfo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Melba D’AStolfo has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Messina
Dipartimento di Fisica, Università di Roma Sapienza, 00185, Roma
8 shared publications - Cesidio Capoccia
Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali di Frascati, 00044, Frascati
8 shared publications - Cristina Maria Bernardes Monteiro
University of Coimbra
8 shared publications - David José Gaspar Marques
Gran Sasso Science Institute
8 shared publications - Davide Fiorina
INFN Sezione di Pavia
8 shared publications - Davide Pinci
INFN Sezione di Roma La Sapienza
8 shared publications
Latest Publications
- 24 September 2026
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (38) , 385103
Characterization of cutting-edge CMOS active pixel sensors within the CYGNO experiment
Time projection chambers equipped with gas electron multipliers and optical readout by scientific CMOS cameras are a promising technology for low-energy particle detection, as demonstrated by the CYGNO experiment. To help identify an optimal detector configuration, we performed a characterization of two state-of-the-art CMOS sensors focusing on dark signal behavior across different exposure times and on detection sensitivity, assessed using the x-ray emissions from a 55 Fe radioactive source, reproducing the low-light conditions expected in the experiment. CYGNO currently employs a low-noise ORCA-Fusion sensor produced by Hamamatsu for validation of its detection system. However, Hamamatsu has introduced two new sensors that could be of interest for future upgrades. The first is an upgraded model of the current sensor, the ORCA-Fusion-BT, featuring a back-illuminated design that reaches a quantum efficiency of up to 95% at 550 nm. The second is a next-generation sensor referred to as the ORCA-Quest. While its peak quantum efficiency is not as high as that of the ORCA-Fusion-BT, it offers high sensitivity across a broader spectral range, extending into the ultraviolet region, and delivers ultra-low readout noise of 0.27 electrons, about 2.6 times lower than that of the Fusion family. These sensors therefore represent an opportunity to enhance the performance of experiments, including those conducted by the CYGNO collaboration. This document presents a characterization of these sensors to evaluate their relevance in photon-limited environments and their suitability for integration into the CYGNO detector system.
- 24 September 2026
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (38) , 385103
Characterization of cutting-edge CMOS active pixel sensors within the CYGNO experiment
Time projection chambers equipped with gas electron multipliers and optical readout by scientific CMOS cameras are a promising technology for low-energy particle detection, as demonstrated by the CYGNO experiment. To help identify an optimal detector configuration, we performed a characterization of two state-of-the-art CMOS sensors focusing on dark signal behavior across different exposure times and on detection sensitivity, assessed using the x-ray emissions from a 55 Fe radioactive source, reproducing the low-light conditions expected in the experiment. CYGNO currently employs a low-noise ORCA-Fusion sensor produced by Hamamatsu for validation of its detection system. However, Hamamatsu has introduced two new sensors that could be of interest for future upgrades. The first is an upgraded model of the current sensor, the ORCA-Fusion-BT, featuring a back-illuminated design that reaches a quantum efficiency of up to 95% at 550 nm. The second is a next-generation sensor referred to as the ORCA-Quest. While its peak quantum efficiency is not as high as that of the ORCA-Fusion-BT, it offers high sensitivity across a broader spectral range, extending into the ultraviolet region, and delivers ultra-low readout noise of 0.27 electrons, about 2.6 times lower than that of the Fusion family. These sensors therefore represent an opportunity to enhance the performance of experiments, including those conducted by the CYGNO collaboration. This document presents a characterization of these sensors to evaluate their relevance in photon-limited environments and their suitability for integration into the CYGNO detector system.
- Open Access
- 1 September 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (09) , P09034
Characterization of field cage and cathode for low radioactivity operation with the CYGNO experiment
Dark matter, which is considered to account for approximately the 27% of the Universe's energy-mass content, remains an open issue in modern particle physics along with its composition. The CYGNO Experiment aims to exploit an innovative approach applied to the direct detection search of low energy nuclear recoils possibly induced by cold particle-like dark matter candidates. CYGNO employs a directional detector based on a Time Projection Chamber (TPC) filled with a He:CF 4 gas mixture and equipped with an optical readout. Currently, the CYGNO Collaboration is constructing the detector demonstrator, CYGNO-04, in Hall F at Laboratori Nazionali del Gran Sasso (LNGS). This 0.4 m 3 detector has the goal of proving the scalability of the technology and assessing the physics and radiopurity capabilities. Given the low radioactivity requirements, especially in internal components such as field cage and cathode, the reduction of material while keeping the correct electrical behavior is paramount. In this paper, we present the validation of several internal components, mainly focusing on the field cage material and support structure. The tests included geometrical asymmetries in the electric field response, collection efficiency as well as measurement of known physical quantities. A preferred configuration is found with a structure based on Nylon material which supports a PET or Kapton sheet with copper strips deposited on.
- 1 September 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (09) , P09034
Open AccessCharacterization of field cage and cathode for low radioactivity operation with the CYGNO experiment
Dark matter, which is considered to account for approximately the 27% of the Universe's energy-mass content, remains an open issue in modern particle physics along with its composition. The CYGNO Experiment aims to exploit an innovative approach applied to the direct detection search of low energy nuclear recoils possibly induced by cold particle-like dark matter candidates. CYGNO employs a directional detector based on a Time Projection Chamber (TPC) filled with a He:CF 4 gas mixture and equipped with an optical readout. Currently, the CYGNO Collaboration is constructing the detector demonstrator, CYGNO-04, in Hall F at Laboratori Nazionali del Gran Sasso (LNGS). This 0.4 m 3 detector has the goal of proving the scalability of the technology and assessing the physics and radiopurity capabilities. Given the low radioactivity requirements, especially in internal components such as field cage and cathode, the reduction of material while keeping the correct electrical behavior is paramount. In this paper, we present the validation of several internal components, mainly focusing on the field cage material and support structure. The tests included geometrical asymmetries in the electric field response, collection efficiency as well as measurement of known physical quantities. A preferred configuration is found with a structure based on Nylon material which supports a PET or Kapton sheet with copper strips deposited on.
- Open Access
- 1 June 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (06) , P06024
Simulation of the CYGNO gaseous TPC optical readout
Gaseous Time Projection Chambers with Optical Readout are sensitive detectors suitable for 3D measurement of low-energy particles (of order 1 keV) and are proposed for detecting rare events such as Dark Matter particle interactions. The CYGNO collaboration is developing such a detector with a high spatial and energy resolution, leveraging an innovative optical readout system. A reliable simulation of the detector response is needed to properly assess the physics reach of this technique and to better understand the performance of the detector in the development phase. Such a simulation cannot entirely rely on existing software packages; indeed, none of the available tools is capable of properly and reliably treating the different phenomena occurring in the detector, from the primary interaction in the gas volume throughout the whole detector response model, including charge transport, light production and propagation, and the response of the optical sensors. In this paper, we present a modeling of the detector response tuned on the CYGNO Optical TPC case; a description of the method is reported together with comparisons with experimental data from the LIME prototype to demonstrate the simulation performances.
- 1 June 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (06) , P06024
Open AccessSimulation of the CYGNO gaseous TPC optical readout
Gaseous Time Projection Chambers with Optical Readout are sensitive detectors suitable for 3D measurement of low-energy particles (of order 1 keV) and are proposed for detecting rare events such as Dark Matter particle interactions. The CYGNO collaboration is developing such a detector with a high spatial and energy resolution, leveraging an innovative optical readout system. A reliable simulation of the detector response is needed to properly assess the physics reach of this technique and to better understand the performance of the detector in the development phase. Such a simulation cannot entirely rely on existing software packages; indeed, none of the available tools is capable of properly and reliably treating the different phenomena occurring in the detector, from the primary interaction in the gas volume throughout the whole detector response model, including charge transport, light production and propagation, and the response of the optical sensors. In this paper, we present a modeling of the detector response tuned on the CYGNO Optical TPC case; a description of the method is reported together with comparisons with experimental data from the LIME prototype to demonstrate the simulation performances.
- Open Access
- 1 June 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (06) , C06006
The CYGNO experiment: a gaseous TPC with optical readout for rare events searches
The CYGNO collaboration is developing a novel strategy for directional Dark Matter searches based on a gaseous Time Projection Chamber (TPC). The detector is optimized for the exploration of light (0.5–50 GeV) WIMPs-like particles and employs a He/CF 4 gas mixture at atmospheric pressure, sensitive to both spin-dependent and spin-independent interactions. A key feature of the project is its optical readout, which relies on photon detection rather than charge collection. In CYGNO detectors, electrons released by ionizing tracks drift toward an amplification stage of three Gas Electron Multipliers (GEMs). The electron avalanches generate scintillation light that is captured by scientific CMOS (sCMOS) cameras for high-resolution two-dimensional imaging and by Photomultiplier Tubes (PMTs) that provide a precise time profile along the drift direction. This allows a 3D event reconstruction, detailed energy deposition mapping, and effective topology and head-to-tail discrimination. Building on the achievements of the 50 L prototype (LIME), which successfully operated underground at LNGS, the next step is the deployment of a 0.4 m 3 demonstrator, CYGNO-04, to be completed in 2026. The demonstrator will validate scalability and confirm the advantages of the proposed technique. Recent results from LIME highlight strong progress in 3D tracking and particle identification. The current status of CYGNO-04 and its role in advancing the program will be presented as well.
- 1 June 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (06) , C06006
Open AccessThe CYGNO experiment: a gaseous TPC with optical readout for rare events searches
The CYGNO collaboration is developing a novel strategy for directional Dark Matter searches based on a gaseous Time Projection Chamber (TPC). The detector is optimized for the exploration of light (0.5–50 GeV) WIMPs-like particles and employs a He/CF 4 gas mixture at atmospheric pressure, sensitive to both spin-dependent and spin-independent interactions. A key feature of the project is its optical readout, which relies on photon detection rather than charge collection. In CYGNO detectors, electrons released by ionizing tracks drift toward an amplification stage of three Gas Electron Multipliers (GEMs). The electron avalanches generate scintillation light that is captured by scientific CMOS (sCMOS) cameras for high-resolution two-dimensional imaging and by Photomultiplier Tubes (PMTs) that provide a precise time profile along the drift direction. This allows a 3D event reconstruction, detailed energy deposition mapping, and effective topology and head-to-tail discrimination. Building on the achievements of the 50 L prototype (LIME), which successfully operated underground at LNGS, the next step is the deployment of a 0.4 m 3 demonstrator, CYGNO-04, to be completed in 2026. The demonstrator will validate scalability and confirm the advantages of the proposed technique. Recent results from LIME highlight strong progress in 3D tracking and particle identification. The current status of CYGNO-04 and its role in advancing the program will be presented as well.
- Open Access
- 1 April 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (04) , T04004
Upgrade of the trigger and data acquisition system for continuous imaging and multi-camera operation in CYGNO
The CYGNO experiment employs an optical readout to image particle interactions in a gaseous Time Projection Chamber (TPC), combining cameras and photomultiplier tubes (PMTs) to achieve high spatial resolution and timing information. This approach enables detailed track reconstruction but poses significant challenges for data acquisition, particularly in view of the next experimental phase, CYGNO-04, which will operate multiple cameras simultaneously. In this paper, we present an upgrade of the CYGNO Trigger and Data Acquisition (T-DAQ) system, developed starting from the LIME configuration and validated on the MANGO prototype. The upgrade introduces a continuous imaging acquisition mode, substantially reducing the camera dead time, together with an extended trigger time-tagging scheme that provides a robust global time reference for PMT signals. A synchronous multi-camera DAQ architecture is also implemented and tested, enabling coordinated operation of multiple optical sensors without a master camera. The performance of the upgraded system is validated through dedicated tests, demonstrating stable continuous acquisition, reliable time-tagging, and consistent synchronization across multiple cameras. These results establish a solid and scalable foundation for the CYGNO-04 DAQ and represent a key step toward efficient data acquisition in future large-scale optical TPC detectors.
- 1 April 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (04) , T04004
Open AccessUpgrade of the trigger and data acquisition system for continuous imaging and multi-camera operation in CYGNO
The CYGNO experiment employs an optical readout to image particle interactions in a gaseous Time Projection Chamber (TPC), combining cameras and photomultiplier tubes (PMTs) to achieve high spatial resolution and timing information. This approach enables detailed track reconstruction but poses significant challenges for data acquisition, particularly in view of the next experimental phase, CYGNO-04, which will operate multiple cameras simultaneously. In this paper, we present an upgrade of the CYGNO Trigger and Data Acquisition (T-DAQ) system, developed starting from the LIME configuration and validated on the MANGO prototype. The upgrade introduces a continuous imaging acquisition mode, substantially reducing the camera dead time, together with an extended trigger time-tagging scheme that provides a robust global time reference for PMT signals. A synchronous multi-camera DAQ architecture is also implemented and tested, enabling coordinated operation of multiple optical sensors without a master camera. The performance of the upgraded system is validated through dedicated tests, demonstrating stable continuous acquisition, reliable time-tagging, and consistent synchronization across multiple cameras. These results establish a solid and scalable foundation for the CYGNO-04 DAQ and represent a key step toward efficient data acquisition in future large-scale optical TPC detectors.
- Open Access
- 1 April 2026
- Published by IOP Publishing in Machine Learning: Science and Technology
- Vol. 7 (2) , 025058
Fast reconstruction-based ROI triggering via anomaly detection in the CYGNO optical TPC
Optical-readout time projection chambers (TPCs) produce megapixel-scale images whose fine-grained topological information is essential for rare-event searches, but whose size challenges real-time data selection. We present an unsupervised, reconstruction-based anomaly-detection strategy for fast region-of-interest (ROI) extraction that operates directly on minimally processed camera frames. A convolutional autoencoder (AE) trained exclusively on pedestal images learns the detector noise morphology without labels, simulation, or fine-grained calibration. Applied to standard data-taking frames, localized reconstruction residuals identify particle-induced structures, from which compact ROIs are extracted via thresholding and spatial clustering. Using real data from the CYGNO optical TPC prototype, we compare two pedestal-trained AE configurations that differ only in their training objective, enabling a controlled study of its impact. The best configuration retains ( 93.0 ± 0.2 ) % of reconstructed signal intensity while discarding ( 97.8 ± 0.1 ) % of the image area, with an inference time of ∼25 ms per frame on a consumer GPU. The results demonstrate that careful design of the training objective is critical for effective reconstruction-based anomaly detection and that pedestal-trained AEs provide a transparent and detector-agnostic baseline for online data reduction in optical TPCs.
- 1 April 2026
- Published by IOP Publishing in Machine Learning: Science and Technology
- Vol. 7 (2) , 025058
Open AccessFast reconstruction-based ROI triggering via anomaly detection in the CYGNO optical TPC
Optical-readout time projection chambers (TPCs) produce megapixel-scale images whose fine-grained topological information is essential for rare-event searches, but whose size challenges real-time data selection. We present an unsupervised, reconstruction-based anomaly-detection strategy for fast region-of-interest (ROI) extraction that operates directly on minimally processed camera frames. A convolutional autoencoder (AE) trained exclusively on pedestal images learns the detector noise morphology without labels, simulation, or fine-grained calibration. Applied to standard data-taking frames, localized reconstruction residuals identify particle-induced structures, from which compact ROIs are extracted via thresholding and spatial clustering. Using real data from the CYGNO optical TPC prototype, we compare two pedestal-trained AE configurations that differ only in their training objective, enabling a controlled study of its impact. The best configuration retains ( 93.0 ± 0.2 ) % of reconstructed signal intensity while discarding ( 97.8 ± 0.1 ) % of the image area, with an inference time of ∼25 ms per frame on a consumer GPU. The results demonstrate that careful design of the training objective is critical for effective reconstruction-based anomaly detection and that pedestal-trained AEs provide a transparent and detector-agnostic baseline for online data reduction in optical TPCs.
- Open Access
- 7 February 2026
- Published by Springer Nature in The European Physical Journal C
- Vol. 86 (2) , 123
Modeling the light response of an optically readout GEM based TPC for the CYGNO experiment
The use of gaseous Time Projection Chambers enables the detection and the detailed study of rare events due to particles interactions with the atoms of the gas with energy releases as low as a few keV. Due to this capability, these instruments are being developed for applications in the field of astroparticle physics, such as the study of dark matter and neutrinos. To acquire events occurring in the sensitive volume with a high granularity, the Cygno collaboration is developing a solution where the light generated during the avalanche processes occurring in a multiplication stage based on Gas Electron Multiplier (GEM) is read out by optical sensors with very high sensitivity and spatial resolution. To achieve a high light output, gas gain values of the order of $$10^5\text {-}10^6$$ are needed. In this working condition, a dependence of the detector response on the spatial density of the charge collected in the GEM holes has been observed, indicating a gain-reduction effect likely caused by space-charge buildup within the multiplication channels. This paper presents data collected with a prototype featuring a sensitive volume of about two liters, together with a model developed by the collaboration to describe and predict the gain dependence on charge density. A comparison with experimental data shows that the model reproduces, with a percent-level precision, the gain behaviour over nearly one order of magnitude.- 7 February 2026
- Published by Springer Nature in The European Physical Journal C
- Vol. 86 (2) , 123
Open AccessModeling the light response of an optically readout GEM based TPC for the CYGNO experiment
The use of gaseous Time Projection Chambers enables the detection and the detailed study of rare events due to particles interactions with the atoms of the gas with energy releases as low as a few keV. Due to this capability, these instruments are being developed for applications in the field of astroparticle physics, such as the study of dark matter and neutrinos. To acquire events occurring in the sensitive volume with a high granularity, the Cygno collaboration is developing a solution where the light generated during the avalanche processes occurring in a multiplication stage based on Gas Electron Multiplier (GEM) is read out by optical sensors with very high sensitivity and spatial resolution. To achieve a high light output, gas gain values of the order of $$10^5\text {-}10^6$$ are needed. In this working condition, a dependence of the detector response on the spatial density of the charge collected in the GEM holes has been observed, indicating a gain-reduction effect likely caused by space-charge buildup within the multiplication channels. This paper presents data collected with a prototype featuring a sensitive volume of about two liters, together with a model developed by the collaboration to describe and predict the gain dependence on charge density. A comparison with experimental data shows that the model reproduces, with a percent-level precision, the gain behaviour over nearly one order of magnitude. - Open Access
- 6 November 2025
- Published by Springer Nature in The European Physical Journal C
- Vol. 85 (11) , 1-12
Bayesian network 3D event reconstruction in the Cygno optical TPC for dark matter direct detection
The CYGNO experiment is developing a high-resolution gaseous Time Projection Chamber with optical readout for directional dark matter searches. The detector uses a helium-tetrafluoromethane (He:CF $$_4$$ 60:40) gas mixture at atmospheric pressure and a triple Gas Electron Multiplier amplification stage, coupled with a scientific camera for high-resolution 2D imaging and fast photomultipliers for time-resolved scintillation light detection. This setup enables 3D event reconstruction: photomultiplier signals provide depth information, while the camera delivers high-precision transverse resolution. In this work, we present a Bayesian Network-based algorithm designed to reconstruct the events using only the photomultiplier signals, inferring a 3D description of the particle trajectories. The algorithm models the light collection process probabilistically and estimates spatial and intensity parameters on the Gas Electron Multiplier plane, where light emission occurs. It is implemented within the Bayesian Analysis Toolkit and uses Markov Chain Monte Carlo sampling for posterior inference. Validation using data from the CYGNO LIME prototype shows accurate reconstruction of localized and extended straight tracks. Results demonstrate that the Bayesian approach enables robust 3D description and, when combined with camera data, opens the way to future improvements in spatial and energy resolution. This methodology represents a significant step forward in directional dark matter detection, enhancing the identification of nuclear recoil tracks with high spatial resolution.- 6 November 2025
- Published by Springer Nature in The European Physical Journal C
- Vol. 85 (11) , 1-12
Open AccessBayesian network 3D event reconstruction in the Cygno optical TPC for dark matter direct detection
The CYGNO experiment is developing a high-resolution gaseous Time Projection Chamber with optical readout for directional dark matter searches. The detector uses a helium-tetrafluoromethane (He:CF $$_4$$ 60:40) gas mixture at atmospheric pressure and a triple Gas Electron Multiplier amplification stage, coupled with a scientific camera for high-resolution 2D imaging and fast photomultipliers for time-resolved scintillation light detection. This setup enables 3D event reconstruction: photomultiplier signals provide depth information, while the camera delivers high-precision transverse resolution. In this work, we present a Bayesian Network-based algorithm designed to reconstruct the events using only the photomultiplier signals, inferring a 3D description of the particle trajectories. The algorithm models the light collection process probabilistically and estimates spatial and intensity parameters on the Gas Electron Multiplier plane, where light emission occurs. It is implemented within the Bayesian Analysis Toolkit and uses Markov Chain Monte Carlo sampling for posterior inference. Validation using data from the CYGNO LIME prototype shows accurate reconstruction of localized and extended straight tracks. Results demonstrate that the Bayesian approach enables robust 3D description and, when combined with camera data, opens the way to future improvements in spatial and energy resolution. This methodology represents a significant step forward in directional dark matter detection, enhancing the identification of nuclear recoil tracks with high spatial resolution.