Kaijun Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kaijun Xu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Jianjun Ye
School of Civil Engineering, Architecture and Environment, Hubei University of Technology, Wuhan 430068, China
2 shared publications - Houmin Li
School of Civil Engineering, Architecture and The Environment, Hubei University of Technology, Wuhan 430068, China
1 shared publication - Jie Chen
School of Civil Engineering, Architecture and The Environment, Hubei University of Technology, Wuhan 430068, China
1 shared publication - Pengfei Xue
School of Mechanics and Civil Engineering, Jinan University, Guangzhou 510632, China
1 shared publication - Song Li
The First Company of China Eighth Engineering Bureau Ltd., Jinan 250100, China
1 shared publication - Tianlong Wu
School of Civil Engineering, Architecture and Environment, Hubei University of Technology, Wuhan 430068, China
1 shared publication
Latest Publications
- Open Access
Study on the Compressive Mechanical Behavior of Multi-Segment Spliced Beams for Hybrid Prefabricated Reinforced Concrete–Steel Structure Foundation Pit Bracing System
To overcome the inherent drawbacks of cast-in-place reinforced concrete bracing—such as long construction periods and difficult demolition—as well as the relatively high construction cost of steel structure bracing, while fully incorporating the respective technical advantages of these two traditional support systems, this paper proposes a novel hybrid prefabricated reinforced concrete (RC)–steel structure foundation pit bracing system. In order to investigate the overall bearing capacity variation in the standard components of this structure under complex external forces in foundation pits, a numerical model was established using the finite element software ABAQUS. The study examines the trend of the axial compressive bearing capacity of a single standard beam segment as the steel thickness of its external stiffening sleeve varies, as well as the effects of eccentric loading, oblique loading, and the presence or absence of auxiliary supports on the structural bearing capacity of multi-segment beam assemblies. The numerical analysis results show that the bearing capacity of a single beam segment exhibits a strong correlation with the variation in sleeve thickness, and a fitting curve of compressive strength as a function of thickness was derived. For the multi-segment assembly, an increase of 1 mm in the load eccentricity in the Y and Z directions reduces the ultimate peak load by approximately 20.95 kN and 23.94 kN, respectively; in the XY and XZ planes, an increase of 1° in the eccentric angle of the oblique load reduces the peak ultimate bearing capacity by about 6.02 kN and 9.67 kN, respectively. Auxiliary supports have a relatively minor influence on the structural bearing capacity. This research thoroughly explores the bearing capacity of the prefabricated steel–concrete composite and steel structure foundation pit bracing under complex working loads, providing strong support for engineering design and demonstrating broad application prospects.
Open AccessStudy on the Compressive Mechanical Behavior of Multi-Segment Spliced Beams for Hybrid Prefabricated Reinforced Concrete–Steel Structure Foundation Pit Bracing System
To overcome the inherent drawbacks of cast-in-place reinforced concrete bracing—such as long construction periods and difficult demolition—as well as the relatively high construction cost of steel structure bracing, while fully incorporating the respective technical advantages of these two traditional support systems, this paper proposes a novel hybrid prefabricated reinforced concrete (RC)–steel structure foundation pit bracing system. In order to investigate the overall bearing capacity variation in the standard components of this structure under complex external forces in foundation pits, a numerical model was established using the finite element software ABAQUS. The study examines the trend of the axial compressive bearing capacity of a single standard beam segment as the steel thickness of its external stiffening sleeve varies, as well as the effects of eccentric loading, oblique loading, and the presence or absence of auxiliary supports on the structural bearing capacity of multi-segment beam assemblies. The numerical analysis results show that the bearing capacity of a single beam segment exhibits a strong correlation with the variation in sleeve thickness, and a fitting curve of compressive strength as a function of thickness was derived. For the multi-segment assembly, an increase of 1 mm in the load eccentricity in the Y and Z directions reduces the ultimate peak load by approximately 20.95 kN and 23.94 kN, respectively; in the XY and XZ planes, an increase of 1° in the eccentric angle of the oblique load reduces the peak ultimate bearing capacity by about 6.02 kN and 9.67 kN, respectively. Auxiliary supports have a relatively minor influence on the structural bearing capacity. This research thoroughly explores the bearing capacity of the prefabricated steel–concrete composite and steel structure foundation pit bracing under complex working loads, providing strong support for engineering design and demonstrating broad application prospects.
- Open Access
- 11 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (22) , 11956
The Influence of Holes and Beam Sleeves on the Compressive Mechanical Properties of Reinforced Concrete Beam Segments
In the newly developed hybrid prefabricated RC-steel structure (SS) foundation pit bracing system, the main braces are the main load-carrying components, which are assembled from standardized prefabricated reinforced concrete beam segments (referred to as beam segments). To facilitate assembly, beam segments are equipped with beam sleeves and beam-end connection holes. The holes at the end of the beam can cause stress concentration problems, while the beam sleeve has a reinforcing effect on the end of the beam segment. To investigate the influence of beam-end holes and beam sleeves on the compressive mechanical properties of beam segments, a numerical simulation study was conducted. Taking the beam segment (specification: 4500 mm × 700 mm × 800 mm) used in a certain foundation pit support project as the research object (i.e., specimen), Abacus software was first used to build parameterized models of beam segments with holes and beam sleeves using the concrete damaged plasticity model (CDP) and the steel double-line strengthening model. Then the influence of three factors, namely end face friction coefficient, beam-end holes diameter, and beam sleeve thickness, on the axial compression performance of the beam segment specimens was studied. The results indicated that the axial compressive capacity of specimens without a beam sleeve decreased with increasing hole diameter; the axial compressive bearing capacities of specimens with hole diameters of 35 mm, 40 mm, and 45 mm were 13,300 kN, 12,500 kN, and 12,300 kN, respectively, which are 11.3%, 16.7%, and 18% lower than the compressive bearing capacity of specimens without holes (15,000 kN). When both a beam sleeve and holes were present, the holes had a negligible influence on the compressive capacity, while the beam sleeve played a decisive role. The compressive bearing capacity increased with greater beam sleeve thickness; the peak bearing capacities of the specimens with beam sleeves 5 mm, 10 mm, and 15 mm thick were 16,200 kN, 16,500 kN, and 17,600 kN, respectively. As the end face friction coefficient decreased from 0.6 to 0.1, the location of maximum compressive damage shifted toward the end face of the beam segment, and the area of maximum concrete damage gradually migrated toward the hole locations. The study demonstrates that the confinement effect of the beam sleeve can compensate for the weakening effect caused by the holes and confirms that the designs of holes in beam segment ends and in the beam sleeve can meet safety requirements.
- 11 November 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (22) , 11956
Open AccessThe Influence of Holes and Beam Sleeves on the Compressive Mechanical Properties of Reinforced Concrete Beam Segments
In the newly developed hybrid prefabricated RC-steel structure (SS) foundation pit bracing system, the main braces are the main load-carrying components, which are assembled from standardized prefabricated reinforced concrete beam segments (referred to as beam segments). To facilitate assembly, beam segments are equipped with beam sleeves and beam-end connection holes. The holes at the end of the beam can cause stress concentration problems, while the beam sleeve has a reinforcing effect on the end of the beam segment. To investigate the influence of beam-end holes and beam sleeves on the compressive mechanical properties of beam segments, a numerical simulation study was conducted. Taking the beam segment (specification: 4500 mm × 700 mm × 800 mm) used in a certain foundation pit support project as the research object (i.e., specimen), Abacus software was first used to build parameterized models of beam segments with holes and beam sleeves using the concrete damaged plasticity model (CDP) and the steel double-line strengthening model. Then the influence of three factors, namely end face friction coefficient, beam-end holes diameter, and beam sleeve thickness, on the axial compression performance of the beam segment specimens was studied. The results indicated that the axial compressive capacity of specimens without a beam sleeve decreased with increasing hole diameter; the axial compressive bearing capacities of specimens with hole diameters of 35 mm, 40 mm, and 45 mm were 13,300 kN, 12,500 kN, and 12,300 kN, respectively, which are 11.3%, 16.7%, and 18% lower than the compressive bearing capacity of specimens without holes (15,000 kN). When both a beam sleeve and holes were present, the holes had a negligible influence on the compressive capacity, while the beam sleeve played a decisive role. The compressive bearing capacity increased with greater beam sleeve thickness; the peak bearing capacities of the specimens with beam sleeves 5 mm, 10 mm, and 15 mm thick were 16,200 kN, 16,500 kN, and 17,600 kN, respectively. As the end face friction coefficient decreased from 0.6 to 0.1, the location of maximum compressive damage shifted toward the end face of the beam segment, and the area of maximum concrete damage gradually migrated toward the hole locations. The study demonstrates that the confinement effect of the beam sleeve can compensate for the weakening effect caused by the holes and confirms that the designs of holes in beam segment ends and in the beam sleeve can meet safety requirements.