Ping Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ping Li has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Shilong Pan
Nanjing University of Aeronautics and Astronautics
5 shared publications - Dan Zhu
Nanjing University of Aeronautics and Astronautics
3 shared publications - Zhouyang Pan
National Key Laboratory of Microwave Photonics, Nanjing University of Aeronautics and Astronautics, Nanjing, China
3 shared publications - Changlong Du
National Key Laboratory of Microwave Photonics, Nanjing University of Aeronautics and Astronautics, Nanjing, China
2 shared publications - Kunlin Shao
National Key Laboratory of Microwave Photonics, Nanjing University of Aeronautics and Astronautics, Nanjing, China
2 shared publications Li Yang
Nanjing University of Aeronautics and Astronautics
2 shared publications
Latest Publications
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (4) , 3818-3826
Simultaneous Generation of Low-Phase-Noise LO and Reconfigurable Radar Waveforms in a Polarization-Multiplexed Optoelectronic Oscillator
We propose and experimentally demonstrate a polarization-multiplexed optoelectronic oscillator (OEO) that simultaneously generates a Ku-band low-phase-noise local oscillator (LO) signal and X-band high-quality, reconfigurable wideband radar waveforms. The architecture employs a commercial dual-polarization binary phase shift-keying Mach–Zehnder modulator (DP-BPSK MZM), and two orthogonally polarized loops are formed with independently tuned center frequencies defined by electrical bandpass filters. The x-polarized loop generates a Ku-band 14-GHz single-tone LO exhibiting −144-dBc/Hz single-sideband phase noise at a 10-kHz offset. In parallel, the y-polarized loop employs a wideband electrical bandpass filter to generate radar waveforms via either injection locking or active mode locking. Under injection locking, an X-band linear frequency-modulated (LFM) waveform centered at 8.5 GHz with a 2-GHz span (7.5–9.5 GHz) is obtained. Compared with the original LFM signal generated by the arbitrary waveform generator (AWG), the injected waveform benefits from the high- $Q$ factor and filtering effect of the OEO loop, leading to a reduction of more than 40 dB in single-sideband phase noise and an improvement of about 20 dB in spectral signal-to-noise ratio (SNR). Active mode locking enables the generation of 9-GHz microwave pulse trains with repetition rates of 100 kHz, 500 kHz, and 1 MHz, exhibiting a phase noise of −144 dBc/Hz at a 10-kHz offset. Furthermore, staggered double- and triple-pulse sequences are realized by injecting position-encoded Gaussian-shaped waveforms from an AWG. These results confirm the potential of the proposed OEO for multifunctional applications in next-generation high-resolution and antijamming radar systems.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (4) , 3818-3826
Simultaneous Generation of Low-Phase-Noise LO and Reconfigurable Radar Waveforms in a Polarization-Multiplexed Optoelectronic Oscillator
We propose and experimentally demonstrate a polarization-multiplexed optoelectronic oscillator (OEO) that simultaneously generates a Ku-band low-phase-noise local oscillator (LO) signal and X-band high-quality, reconfigurable wideband radar waveforms. The architecture employs a commercial dual-polarization binary phase shift-keying Mach–Zehnder modulator (DP-BPSK MZM), and two orthogonally polarized loops are formed with independently tuned center frequencies defined by electrical bandpass filters. The x-polarized loop generates a Ku-band 14-GHz single-tone LO exhibiting −144-dBc/Hz single-sideband phase noise at a 10-kHz offset. In parallel, the y-polarized loop employs a wideband electrical bandpass filter to generate radar waveforms via either injection locking or active mode locking. Under injection locking, an X-band linear frequency-modulated (LFM) waveform centered at 8.5 GHz with a 2-GHz span (7.5–9.5 GHz) is obtained. Compared with the original LFM signal generated by the arbitrary waveform generator (AWG), the injected waveform benefits from the high- $Q$ factor and filtering effect of the OEO loop, leading to a reduction of more than 40 dB in single-sideband phase noise and an improvement of about 20 dB in spectral signal-to-noise ratio (SNR). Active mode locking enables the generation of 9-GHz microwave pulse trains with repetition rates of 100 kHz, 500 kHz, and 1 MHz, exhibiting a phase noise of −144 dBc/Hz at a 10-kHz offset. Furthermore, staggered double- and triple-pulse sequences are realized by injecting position-encoded Gaussian-shaped waveforms from an AWG. These results confirm the potential of the proposed OEO for multifunctional applications in next-generation high-resolution and antijamming radar systems.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (11) , 4403-4413
A Dispersion-Invariant Reconfigurable Repetition Rate Manipulation Technique Based on Intensity Modulation and the Temporal Talbot Effect
Flexible control of the repetition rate of optical pulse sequences is a critical requirement in modern optoelectronic systems. Traditional repetition rate manipulation (RRM) methods based on the temporal Talbot effect are constrained to integer control factors and require dynamic adjustment of dispersion parameters, which limits their feasibility. To overcome these limitations, we propose a dispersion-invariant reconfigurable RRM technique based on the temporal Talbot effect. The RRM factor in the proposed method is reconfigurable and supports RRM by a family of N/2 factors, where N is a positive integer. In this method, the reconfigurability is achieved by applying a periodic electrical signal to an intensity modulator synchronized with the input pulse sequence. This electrical signal directly defines the RRM factor. Importantly, the required dispersion remains fixed regardless of the RRM factor and depends on the initial repetition period of the input optical pulse sequence. This method overcomes the inherent limitations of the conventional temporal Talbot method. As a proof of concept, we demonstrate RRM with configurable factors ranging from 1/2 to 17/2. Both theoretical analysis and experimental results validate the capability of the proposed scheme to realize N/2 RRM using a straightforward system architecture. Furthermore, we conduct an in-depth study on the impact of high-order dispersion on the stability of the repetition-rate-multiplied pulse sequences. This progress not only expands the practicality of the temporal Talbot effect but also provides a promising solution for applications such as ultrafast signal processing.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (11) , 4403-4413
A Dispersion-Invariant Reconfigurable Repetition Rate Manipulation Technique Based on Intensity Modulation and the Temporal Talbot Effect
Flexible control of the repetition rate of optical pulse sequences is a critical requirement in modern optoelectronic systems. Traditional repetition rate manipulation (RRM) methods based on the temporal Talbot effect are constrained to integer control factors and require dynamic adjustment of dispersion parameters, which limits their feasibility. To overcome these limitations, we propose a dispersion-invariant reconfigurable RRM technique based on the temporal Talbot effect. The RRM factor in the proposed method is reconfigurable and supports RRM by a family of N/2 factors, where N is a positive integer. In this method, the reconfigurability is achieved by applying a periodic electrical signal to an intensity modulator synchronized with the input pulse sequence. This electrical signal directly defines the RRM factor. Importantly, the required dispersion remains fixed regardless of the RRM factor and depends on the initial repetition period of the input optical pulse sequence. This method overcomes the inherent limitations of the conventional temporal Talbot method. As a proof of concept, we demonstrate RRM with configurable factors ranging from 1/2 to 17/2. Both theoretical analysis and experimental results validate the capability of the proposed scheme to realize N/2 RRM using a straightforward system architecture. Furthermore, we conduct an in-depth study on the impact of high-order dispersion on the stability of the repetition-rate-multiplied pulse sequences. This progress not only expands the practicality of the temporal Talbot effect but also provides a promising solution for applications such as ultrafast signal processing.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (9) , 3473-3481
Arbitrary Half-Integer Repetition Rate Multiplication of Optical Pulse Train Based on Temporal Talbot Effect
Optical pulse trains with reconfigurable repetition rate have become an essential component in the modern optical communications systems. However, existing repetition rate tuning methods are largely confined to integer-based multiplication. Methods that can achieve fractional multiplication rely on complex phase modulation signals, which limit flexibility and practical utility. To overcome this limitation, we propose a novel method that enables arbitrary half-integer repetition rate multiplication of optical pulse trains based on the temporal Talbot effect. The method first applies a tailored phase processing step to the input pulses, followed by propagation through a dispersion module, collectively facilitating effective repetition rate multiplication. Compared to existing schemes, this approach uses a highly straightforward phase signal that is independent of the target multiplication factor and focuses on achieving half-integer RRM. Meanwhile, this method significantly enhances control accuracy and expands the adjustable range of repetition rates. A proof-of-concept experiment is conducted, demonstrating repetition rate multiplication factors from 1/2 to 11/2.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (9) , 3473-3481
Arbitrary Half-Integer Repetition Rate Multiplication of Optical Pulse Train Based on Temporal Talbot Effect
Optical pulse trains with reconfigurable repetition rate have become an essential component in the modern optical communications systems. However, existing repetition rate tuning methods are largely confined to integer-based multiplication. Methods that can achieve fractional multiplication rely on complex phase modulation signals, which limit flexibility and practical utility. To overcome this limitation, we propose a novel method that enables arbitrary half-integer repetition rate multiplication of optical pulse trains based on the temporal Talbot effect. The method first applies a tailored phase processing step to the input pulses, followed by propagation through a dispersion module, collectively facilitating effective repetition rate multiplication. Compared to existing schemes, this approach uses a highly straightforward phase signal that is independent of the target multiplication factor and focuses on achieving half-integer RRM. Meanwhile, this method significantly enhances control accuracy and expands the adjustable range of repetition rates. A proof-of-concept experiment is conducted, demonstrating repetition rate multiplication factors from 1/2 to 11/2.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (2) , 1852-1860
Coherent Dual-Band Dual-Chirp Microwave Waveform Generation Based on a Polarization-Multiplexed Optoelectronic Oscillator
We propose and experimentally demonstrate a coherent dual-band dual-chirp microwave waveform generation scheme based on a polarization-multiplexed optoelectronic oscillator (OEO). A dual-polarization binary phase shift-keying (DP-BPSK) modulator is employed to construct orthogonal signal paths, with a dual-passband filter integrated into the OEO loop. Mutual injection locking enables stable dual-frequency oscillations with low phase noise and a high side-mode suppression ratio (SMSR). The generated dual-frequency signal serves as a local oscillator (LO) to modulate an externally injected baseband linear frequency-modulated (LFM) waveform, producing coherent dual-band dual-chirp LFM signals. The proof-of-concept experiments demonstrate waveform generation centered at 10 and 16 GHz with tunable bandwidths, duty cycles, and repetition periods. Compared to a free-running OEO, the proposed scheme improves the SMSR by 36 dB and enhances the signal-to-interference ratio (SIR) of the generated LFM signals by 31 dB. Furthermore, relative to direct waveform synthesis using an arbitrary waveform generator (AWG), it achieves a 29-dB SIR improvement and significantly reduces spectral linewidth. The output bandwidth can be flexibly extended up to 12 GHz by adjusting the baseband chirp, demonstrating high configurability and spectral scalability. Owing to its compact architecture, high coherence, and excellent spectral purity, the proposed approach is well suited for advanced radar systems requiring high resolution and robust interference suppression.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (2) , 1852-1860
Coherent Dual-Band Dual-Chirp Microwave Waveform Generation Based on a Polarization-Multiplexed Optoelectronic Oscillator
We propose and experimentally demonstrate a coherent dual-band dual-chirp microwave waveform generation scheme based on a polarization-multiplexed optoelectronic oscillator (OEO). A dual-polarization binary phase shift-keying (DP-BPSK) modulator is employed to construct orthogonal signal paths, with a dual-passband filter integrated into the OEO loop. Mutual injection locking enables stable dual-frequency oscillations with low phase noise and a high side-mode suppression ratio (SMSR). The generated dual-frequency signal serves as a local oscillator (LO) to modulate an externally injected baseband linear frequency-modulated (LFM) waveform, producing coherent dual-band dual-chirp LFM signals. The proof-of-concept experiments demonstrate waveform generation centered at 10 and 16 GHz with tunable bandwidths, duty cycles, and repetition periods. Compared to a free-running OEO, the proposed scheme improves the SMSR by 36 dB and enhances the signal-to-interference ratio (SIR) of the generated LFM signals by 31 dB. Furthermore, relative to direct waveform synthesis using an arbitrary waveform generator (AWG), it achieves a 29-dB SIR improvement and significantly reduces spectral linewidth. The output bandwidth can be flexibly extended up to 12 GHz by adjusting the baseband chirp, demonstrating high configurability and spectral scalability. Owing to its compact architecture, high coherence, and excellent spectral purity, the proposed approach is well suited for advanced radar systems requiring high resolution and robust interference suppression.
- 11 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (2) , 1770-1779
Photonics-Based Automatic Modulation and State Recognition System for Multifunction Radar
Radar modulation and state recognition for multifunction radar (MFR) play a vital role in electronic warfare systems. However, in wideband scenarios, traditional digital radar recognition systems are challenged by the massive data volume, making it difficult to achieve wideband, real-time, and high-precision recognition. To address this challenge, a photonics-based parameter measurement model is proposed to simultaneously map time, phase, and frequency parameters of wideband radar signals into low-rate electrical measurement pulses, whose amplitude and timing features are used for radar feature extraction. A two-stage learning back-end is introduced to automatically classify the radar states. By uniting the ultrafast photonics-based feature extraction front-end with the attention-driven neural inference, the proposed system transcends digitization limits and maximizes situational-awareness accuracy. A proof-of-concept experiment is conducted. The proposed work successfully recognizes nine modulation types and five states within a 19–29-GHz frequency range, with SNR varying from −20 to 19 dB. The required sampling rate is significantly reduced from 58 GSa/s to 150 MSa/s, and the computational complexity is reduced from 26 427 to 64.98 GFLOPs.
- 11 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (2) , 1770-1779
Photonics-Based Automatic Modulation and State Recognition System for Multifunction Radar
Radar modulation and state recognition for multifunction radar (MFR) play a vital role in electronic warfare systems. However, in wideband scenarios, traditional digital radar recognition systems are challenged by the massive data volume, making it difficult to achieve wideband, real-time, and high-precision recognition. To address this challenge, a photonics-based parameter measurement model is proposed to simultaneously map time, phase, and frequency parameters of wideband radar signals into low-rate electrical measurement pulses, whose amplitude and timing features are used for radar feature extraction. A two-stage learning back-end is introduced to automatically classify the radar states. By uniting the ultrafast photonics-based feature extraction front-end with the attention-driven neural inference, the proposed system transcends digitization limits and maximizes situational-awareness accuracy. A proof-of-concept experiment is conducted. The proposed work successfully recognizes nine modulation types and five states within a 19–29-GHz frequency range, with SNR varying from −20 to 19 dB. The required sampling rate is significantly reduced from 58 GSa/s to 150 MSa/s, and the computational complexity is reduced from 26 427 to 64.98 GFLOPs.