Amariah Condon
Amariah Condon has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Peter M. Attia
Glimpse Engineering Inc
4 shared publications Aiden Larson
Aiiso Yufeng Li Family Department of Chemical and Nano Engineering, University of California, San Diego, La Jolla, California 92093, United States of America
1 shared publication- Alex Liu
Aiiso Yufeng Li Family Department of Chemical and Nano Engineering University of California San Diego, La Jolla CA 92093 USA
1 shared publication - Amin Kazem-Ghamsari
Department of Mechanical and Industrial Engineering, Northeastern University, Boston, Massachusetts 02115, United States of America
1 shared publication - Claire Floras
Dalhousie University
1 shared publication - Daniel A. Cogswell
Massachusetts Institute of Technology
1 shared publication
Latest Publications
- Open Access
- 10 April 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (7) , 070515
Visualization and Detection of Internal Damage Caused by External Mechanical Loads in Cylindrical Li-Ion Batteries
Detecting and preventing lithium-ion battery failures remains a critical challenge, as failures degrade performance, damage materials, and pose safety risks. While catastrophic outcomes under extreme impacts or compression—such as short circuits, thermal runaway, and fires—have been extensively studied, batteries in real-world applications are more often exposed to moderate stresses. These conditions produce small internal changes with weak initial electrochemical signatures that can accumulate into severe damage over time. This work investigates how single-impact and compressive forces of varying intensities and orientations affect the structure and electrochemical behavior of 18650 NMC/graphite cylindrical cells. X-ray computed tomography (CT) provides direct visualization of damage to both active and inactive components, while open-circuit potential, impedance spectroscopy, and charge-discharge cycling collectively capture electrochemical consequences. The results reveal immediate yet modest capacity loss even after a single mechanical event, with damaged cells later showing cycling performance comparable to intact cells if only minor damage is introduced. However, repeated loading produces cumulative degradation, further aggravated by subsequent electrochemical cycling. CT imaging highlights structural changes invisible to conventional diagnostics, while electrochemical tests expose early functional impacts. Together, these complementary methods advance understanding of how moderate mechanical damage initiates, evolves, and compromises long-term reliability in lithium-ion batteries.
- 10 April 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (7) , 070515
Open AccessVisualization and Detection of Internal Damage Caused by External Mechanical Loads in Cylindrical Li-Ion Batteries
Detecting and preventing lithium-ion battery failures remains a critical challenge, as failures degrade performance, damage materials, and pose safety risks. While catastrophic outcomes under extreme impacts or compression—such as short circuits, thermal runaway, and fires—have been extensively studied, batteries in real-world applications are more often exposed to moderate stresses. These conditions produce small internal changes with weak initial electrochemical signatures that can accumulate into severe damage over time. This work investigates how single-impact and compressive forces of varying intensities and orientations affect the structure and electrochemical behavior of 18650 NMC/graphite cylindrical cells. X-ray computed tomography (CT) provides direct visualization of damage to both active and inactive components, while open-circuit potential, impedance spectroscopy, and charge-discharge cycling collectively capture electrochemical consequences. The results reveal immediate yet modest capacity loss even after a single mechanical event, with damaged cells later showing cycling performance comparable to intact cells if only minor damage is introduced. However, repeated loading produces cumulative degradation, further aggravated by subsequent electrochemical cycling. CT imaging highlights structural changes invisible to conventional diagnostics, while electrochemical tests expose early functional impacts. Together, these complementary methods advance understanding of how moderate mechanical damage initiates, evolves, and compromises long-term reliability in lithium-ion batteries.
- Open Access
- 11 March 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (5) , 050519
Electrolyte Motion Induced Salt Inhomogeneity in Si-Containing Cylindrical Cells – A Case Study
Electrolyte motion induced salt inhomogeneity (EMSI) is a failure mechanism in cylindrical and prismatic lithium-ion batteries that can lead to rapid capacity loss at high rates and eventually Li plating and cell failure. If a cell displaying EMSI is allowed to rest for several weeks before the onset of Li plating, capacity recovery is possible. This work studies the effect of varied anode silicon oxide (SiO x ) content (0 to 15% Si by weight) on EMSI in cylindrical 18650 cells by measuring capacity loss, changes in electrolyte resistance, and bulk movement of electrolyte via both moment of inertia measurements and X-ray CT imaging. With increased SiO x content, cells pump more electrolyte, display increasing electrolyte resistance with cycle number and show accelerated capacity loss. This trend did not hold true for the cell with the most SiO x , which showed electrolyte pumping without EMSI. This was possible due to a low porosity anode, which generates electrolyte pumping from both cathode and anode and does not lead to inhomogeneous salt distributions. This cell was also underfilled, likely reducing the amount of electrolyte motion. A simple model is presented for predicting the rest times required for a cell to equilibrate the electrolyte salt gradients, which agrees well with the experimental data. Three days is a typical “relaxation half-life” for these cells, with full capacity recovery after 30 1 C/1 C cycles taking up to two weeks.
- 11 March 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (5) , 050519
Open AccessElectrolyte Motion Induced Salt Inhomogeneity in Si-Containing Cylindrical Cells – A Case Study
Electrolyte motion induced salt inhomogeneity (EMSI) is a failure mechanism in cylindrical and prismatic lithium-ion batteries that can lead to rapid capacity loss at high rates and eventually Li plating and cell failure. If a cell displaying EMSI is allowed to rest for several weeks before the onset of Li plating, capacity recovery is possible. This work studies the effect of varied anode silicon oxide (SiO x ) content (0 to 15% Si by weight) on EMSI in cylindrical 18650 cells by measuring capacity loss, changes in electrolyte resistance, and bulk movement of electrolyte via both moment of inertia measurements and X-ray CT imaging. With increased SiO x content, cells pump more electrolyte, display increasing electrolyte resistance with cycle number and show accelerated capacity loss. This trend did not hold true for the cell with the most SiO x , which showed electrolyte pumping without EMSI. This was possible due to a low porosity anode, which generates electrolyte pumping from both cathode and anode and does not lead to inhomogeneous salt distributions. This cell was also underfilled, likely reducing the amount of electrolyte motion. A simple model is presented for predicting the rest times required for a cell to equilibrate the electrolyte salt gradients, which agrees well with the experimental data. Three days is a typical “relaxation half-life” for these cells, with full capacity recovery after 30 1 C/1 C cycles taking up to two weeks.
- Open Access
- 1 December 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (12) , 120509
Geometric Changes in Cylindrical Batteries as a Function of State of Charge
High-resolution, high-throughput CT scanning of commercial lithium-ion and sodium-ion cylindrical batteries provides quantitative detail into subtle geometrical changes occurring as a function of state-of-charge. Precise quantification via computer vision algorithms reveals a core area change with reversible and irreversible components in EVE lithium-ion cells, hysteresis in can eccentricity in Samsung lithium-ion cells, and the absence of significant geometrical changes in HAKADI sodium-ion cells. The difference in metrics between charge and discharge is introduced to remove the influence of tabs. The results demonstrate the potential of CT as a quasi-in-situ imaging technique for capturing sensitive geometric changes during cycling.
- 1 December 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (12) , 120509
Open AccessGeometric Changes in Cylindrical Batteries as a Function of State of Charge
High-resolution, high-throughput CT scanning of commercial lithium-ion and sodium-ion cylindrical batteries provides quantitative detail into subtle geometrical changes occurring as a function of state-of-charge. Precise quantification via computer vision algorithms reveals a core area change with reversible and irreversible components in EVE lithium-ion cells, hysteresis in can eccentricity in Samsung lithium-ion cells, and the absence of significant geometrical changes in HAKADI sodium-ion cells. The difference in metrics between charge and discharge is introduced to remove the influence of tabs. The results demonstrate the potential of CT as a quasi-in-situ imaging technique for capturing sensitive geometric changes during cycling.
- Open Access
- 1 November 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (11) , 110536
Design and Performance of the BYD LFP/Graphite 4680 Cylindrical Cell
The increasing demand for large-format lithium-ion batteries in electric vehicles has accelerated the development of cell formats that offer higher energy density and improved pack-level efficiency. Among these, the 4680 cylindrical cell format, pioneered by Tesla, has gained widespread adoption due to its potential to simplify battery pack architecture while enhancing gravimetric energy density. Other cell manufacturers, including SamSung, Panasonic, BYD, and others, have adopted the 46XX format, incorporating various chemistries. This study presents a comprehensive analysis of BYD’s 4680 lFP/graphite cylindrical lithium-ion cells. Detailed physical teardown, X-ray imaging, electrochemical testing, and electron imaging were performed to evaluate both cell- and materials-level attributes. The teardown and X-ray imaging reveal an uncommon multi-tab configuration and homogeneously double-sided electrode coatings, with no silicon additives in the graphite anode. Electrochemical testing indicates energy densities of 374.6 Wh l −1 and 150.5 Wh kg −1 . Furthermore, hybrid pulse power characterization and electrochemical impedance spectroscopy show impressive rate capability, with low cell-level DC area-specific resistance (6–17 Ω·cm 2 across various SOCs) and an area-specific charge transfer resistance of approximately 5.9 Ω·cm 2 . These findings highlight a new direction for the 4680-cell format in both design and performance, establishing a strong foundation for future developments in large-format cylindrical battery technology.
- 1 November 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (11) , 110536
Open AccessDesign and Performance of the BYD LFP/Graphite 4680 Cylindrical Cell
The increasing demand for large-format lithium-ion batteries in electric vehicles has accelerated the development of cell formats that offer higher energy density and improved pack-level efficiency. Among these, the 4680 cylindrical cell format, pioneered by Tesla, has gained widespread adoption due to its potential to simplify battery pack architecture while enhancing gravimetric energy density. Other cell manufacturers, including SamSung, Panasonic, BYD, and others, have adopted the 46XX format, incorporating various chemistries. This study presents a comprehensive analysis of BYD’s 4680 lFP/graphite cylindrical lithium-ion cells. Detailed physical teardown, X-ray imaging, electrochemical testing, and electron imaging were performed to evaluate both cell- and materials-level attributes. The teardown and X-ray imaging reveal an uncommon multi-tab configuration and homogeneously double-sided electrode coatings, with no silicon additives in the graphite anode. Electrochemical testing indicates energy densities of 374.6 Wh l −1 and 150.5 Wh kg −1 . Furthermore, hybrid pulse power characterization and electrochemical impedance spectroscopy show impressive rate capability, with low cell-level DC area-specific resistance (6–17 Ω·cm 2 across various SOCs) and an area-specific charge transfer resistance of approximately 5.9 Ω·cm 2 . These findings highlight a new direction for the 4680-cell format in both design and performance, establishing a strong foundation for future developments in large-format cylindrical battery technology.