An Huynh-Thai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
An Huynh-Thai has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Toan Pham-Bao
Ho Chi Minh City University of Technology (HCMUT), VNU-HCM
3 shared publications - Luan Vuong-Cong
Ho Chi Minh City University of Technology (HCMUT)
2 shared publications - Cong Hoa Vu
Chonbuk National University
1 shared publication - Hung Nguyen-Quoc
Ho Chi Minh City University of Technology (HCMUT)
1 shared publication - Nhi Ngo-Kieu
Ho Chi Minh City University of Technology (HCMUT), VNU-HCM
1 shared publication - Quynh Le-Bao
Ho Chi Minh City University of Technology (HCMUT), VNU-HCM
1 shared publication
Latest Publications
- Open Access
- 22 January 2026
- Published by Gruppo Italiano Frattura
- Vol. 20 (76) , 99-116
The damping influence in monitoring the tension of cable using the vibration method
In the maintenance work of cable configurations, which have limitations such as cables in cable-stayed bridges, suspenders in suspension bridges, and hangers in arch bridges, tension on the cables is required. The safety of the cable is confirmed by checking whether the tensile force on the cable is within the allowable value. In the current widespread practice, cable tension is estimated using the vibration method by measuring the natural frequencies of the cable. However, this method is affected by several factors, including flexural rigidity, sag, and damper. The main difference is that natural frequencies (ωn) are the theoretical frequency of vibration without any energy loss, while damped natural frequencies (ωd) are of the actual system where damping (energy loss) is present. The undamped frequency is a system's inherent property based on its mass and stiffness, while the damped frequency is a practical measurement that is always less than the undamped frequency. This paper proposes a novel method for estimating tensile force that considers global damping. To model the cable as a Rayleigh beam, a theoretical equation for a viscoelastic system has been developed to estimate the natural frequency. The solution method calculates the cable tension and the material damping simultaneously from the natural frequencies. Previous studies verified the validity of the method. The maximum error in the tension is in the range of 4.71% in all valid tests. The evidence confirms the effectiveness of the proposed methods in tension estimation. In this research, the influence of damping on the evaluation of tension is investigated through analytical model, in which the natural frequencies, determined by the damping levels and the damped natural frequencies (measured frequencies). Then, the Hierarchical Bayes model was used to find stable estimates while preserving partial pooling, under sparse data, to stabilize estimates and fully quantify uncertainty. The results show that neglecting damping can cause noticeable errors, especially in low-tension or short cables. The study emphasizes the importance of considering damping in vibration-based tensile force assessments to enhance accuracy and reliability.
- 22 January 2026
- Published by Gruppo Italiano Frattura
- Vol. 20 (76) , 99-116
Open AccessThe damping influence in monitoring the tension of cable using the vibration method
In the maintenance work of cable configurations, which have limitations such as cables in cable-stayed bridges, suspenders in suspension bridges, and hangers in arch bridges, tension on the cables is required. The safety of the cable is confirmed by checking whether the tensile force on the cable is within the allowable value. In the current widespread practice, cable tension is estimated using the vibration method by measuring the natural frequencies of the cable. However, this method is affected by several factors, including flexural rigidity, sag, and damper. The main difference is that natural frequencies (ωn) are the theoretical frequency of vibration without any energy loss, while damped natural frequencies (ωd) are of the actual system where damping (energy loss) is present. The undamped frequency is a system's inherent property based on its mass and stiffness, while the damped frequency is a practical measurement that is always less than the undamped frequency. This paper proposes a novel method for estimating tensile force that considers global damping. To model the cable as a Rayleigh beam, a theoretical equation for a viscoelastic system has been developed to estimate the natural frequency. The solution method calculates the cable tension and the material damping simultaneously from the natural frequencies. Previous studies verified the validity of the method. The maximum error in the tension is in the range of 4.71% in all valid tests. The evidence confirms the effectiveness of the proposed methods in tension estimation. In this research, the influence of damping on the evaluation of tension is investigated through analytical model, in which the natural frequencies, determined by the damping levels and the damped natural frequencies (measured frequencies). Then, the Hierarchical Bayes model was used to find stable estimates while preserving partial pooling, under sparse data, to stabilize estimates and fully quantify uncertainty. The results show that neglecting damping can cause noticeable errors, especially in low-tension or short cables. The study emphasizes the importance of considering damping in vibration-based tensile force assessments to enhance accuracy and reliability.
- 20 November 2025
- Published by Springer Nature
- p. 985-992
Investigating Natural Frequencies of Sand Soil Ground for Predicting Landslide Based on Field Tests
- 20 November 2025
- Published by Springer Nature
- p. 985-992
Investigating Natural Frequencies of Sand Soil Ground for Predicting Landslide Based on Field Tests
- 10 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 104-108
Determining Cable Tensile Loads Considering Viscous Damping
Recently., determining the tensile load in the structures with cable., such as suspension bridges and cable-stayed bridges., is an important problem. This structure could be ensured to be durable by structural health monitoring., including structural inspections and patrol measurements. A part of the inspection methods is vibration monitoring; nevertheless., this could be inaccurate because geometry and material characteristics are directly influent., such as cable's material damping and the sag. This research on the dynamic differential equations of vibration cable., which is taken to determine the tensile loads of cables., considers the viscous damping of cable material. After that., the assumption of this research would be simplified boundary conditions. The relation between frequencies and tensile load is obtained by expressions. A practical mechanics model., which is proposed., is used to determine the tensile load of the cables through measured frequency. This model is performed to apply for four cables of a cable-stayed road bridge across the Saigon River in Ho Chi Minh City.
- 10 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 104-108
Determining Cable Tensile Loads Considering Viscous Damping
Recently., determining the tensile load in the structures with cable., such as suspension bridges and cable-stayed bridges., is an important problem. This structure could be ensured to be durable by structural health monitoring., including structural inspections and patrol measurements. A part of the inspection methods is vibration monitoring; nevertheless., this could be inaccurate because geometry and material characteristics are directly influent., such as cable's material damping and the sag. This research on the dynamic differential equations of vibration cable., which is taken to determine the tensile loads of cables., considers the viscous damping of cable material. After that., the assumption of this research would be simplified boundary conditions. The relation between frequencies and tensile load is obtained by expressions. A practical mechanics model., which is proposed., is used to determine the tensile load of the cables through measured frequency. This model is performed to apply for four cables of a cable-stayed road bridge across the Saigon River in Ho Chi Minh City.