Liangyao Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Liangyao Lin has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Kun Xing
Hefei University of Technology
3 shared publications - Bin Liu
Nanjing University
2 shared publications - Chenxue Li
Jiangsu Provincial Key Laboratory of Advanced Photonic and Electronic Materials, School of Electronic Science and Engineering, Nanjing University, Nanjing, China
2 shared publications - Haifeng Wang
School of Microelectronics, Hefei University of Technology , Hefei 230009
2 shared publications Xiaoping Yang
Hefei University of Technology
2 shared publicationsYimeng Sang
Nanjing University
2 shared publications
Latest Publications
- 14 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (11)
Low-voltage GaN tunnel junctions enabled by a thermally reconstructed InGaN sacrificial interlayer
Low-voltage tunnel junctions (TJs) are essential for vertically integrated III-nitride emitters, yet their voltage penalty limits monolithic multicolor integration. We report a GaN-based TJ in which a 5 nm InGaN sacrificial interlayer is thermally reconstructed during a subsequent in-reactor step, producing a laterally redistributed In-rich tunneling interface. Four metalorganic chemical vapor deposition (MOCVD)-grown blue LED samples are compared: a p+-GaN/n+-GaN homojunction (LED A), the same homojunction after a 1000 °C, 3 min treatment (LED A-HT), a TJ with an intact 5 nm n-In0.3Ga0.7N interlayer (LED B), and its reconstructed counterpart (LED C). Cross-sectional TEM and In elemental mapping show a continuous interlayer in TJ B, whereas TJ C contains laterally redistributed In-rich regions and nanoscale void-like structural features; the blue InGaN/GaN quantum wells remain clearly resolved after the thermal process. LED C exhibits a device turn-on voltage of 3.4 V, compared with 4.1 V for LED B and 4.6 V for LED A; LED A-HT shows no comparable reduction. Similar peak wavelengths and linewidths among the four LEDs show that the blue test active region retains its peak position and spectral width after the different TJ treatments. Incorporation of the reconstructed TJ into a monolithic InGaN blue/green/red stack yields selectively driven three-color electroluminescence, wafer-scale PL peak-wavelength standard deviations below 3 nm, and an experimental CIE 1931 triangle area equal to 72.9% of the BT.2020 triangle area at the stated operating points. These results provide an MOCVD-compatible approach to reducing the voltage penalty of buried nitride TJs in vertically integrated emitters.
- 14 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (11)
Low-voltage GaN tunnel junctions enabled by a thermally reconstructed InGaN sacrificial interlayer
Low-voltage tunnel junctions (TJs) are essential for vertically integrated III-nitride emitters, yet their voltage penalty limits monolithic multicolor integration. We report a GaN-based TJ in which a 5 nm InGaN sacrificial interlayer is thermally reconstructed during a subsequent in-reactor step, producing a laterally redistributed In-rich tunneling interface. Four metalorganic chemical vapor deposition (MOCVD)-grown blue LED samples are compared: a p+-GaN/n+-GaN homojunction (LED A), the same homojunction after a 1000 °C, 3 min treatment (LED A-HT), a TJ with an intact 5 nm n-In0.3Ga0.7N interlayer (LED B), and its reconstructed counterpart (LED C). Cross-sectional TEM and In elemental mapping show a continuous interlayer in TJ B, whereas TJ C contains laterally redistributed In-rich regions and nanoscale void-like structural features; the blue InGaN/GaN quantum wells remain clearly resolved after the thermal process. LED C exhibits a device turn-on voltage of 3.4 V, compared with 4.1 V for LED B and 4.6 V for LED A; LED A-HT shows no comparable reduction. Similar peak wavelengths and linewidths among the four LEDs show that the blue test active region retains its peak position and spectral width after the different TJ treatments. Incorporation of the reconstructed TJ into a monolithic InGaN blue/green/red stack yields selectively driven three-color electroluminescence, wafer-scale PL peak-wavelength standard deviations below 3 nm, and an experimental CIE 1931 triangle area equal to 72.9% of the BT.2020 triangle area at the stated operating points. These results provide an MOCVD-compatible approach to reducing the voltage penalty of buried nitride TJs in vertically integrated emitters.
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (9) , 1870-1873
Buried V-Pit Templates for 20.3% Peak EQE at 640 nm in InGaN Red LEDs
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (9) , 1870-1873
Buried V-Pit Templates for 20.3% Peak EQE at 640 nm in InGaN Red LEDs
- 18 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 394-400
Impact of Template Patterning Dimensions on the Performance of InGaN-Based Red Light-Emitting Diodes
The poor efficiency of currently existing InGaN-based red light-emitting diodes (LEDs) is the primary factor limiting the advancement of full-color, high-resolution mini-/micro-LED displays. However, while the application of square tile-patterned GaN templates formed on sapphire substrates has been demonstrated to improve the emission performance of InGaN-based red LEDs, the impact of template size remains poorly understood. This work addresses this issue by preparing square tile-patterned GaN templates with varying tile dimensions of $500\times 500~\mu $ m to $200\times 200~\mu $ m. The impact of template size on the relaxation state, dislocation density, and surface morphology of the GaN template layers is analyzed systematically, and the emission properties of InGaN-based red mini-LED chips fabricated on these GaN templates are characterized in detail. Experimental results indicate that an optimal template size of $300\times 300~\mu $ m not only promotes lateral relaxation of the underlying layers and mitigates the quantum-confined Stark effect (QCSE), but also enhances crystal quality and reduces dislocation density. Consequently, the LEDs fabricated on this template exhibit higher emission intensity and improved wavelength stability compared to conventional InGaN-based red LEDs grown on planar GaN substrates. A red mini-LED fabricated using the optimal template demonstrates a peak emission wavelength of 634.0 nm at 1 A/cm2, with a 57% increase in peak external quantum efficiency (EQE) compared to the LED grown on the unpatterned template.
- 18 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (1) , 394-400
Impact of Template Patterning Dimensions on the Performance of InGaN-Based Red Light-Emitting Diodes
The poor efficiency of currently existing InGaN-based red light-emitting diodes (LEDs) is the primary factor limiting the advancement of full-color, high-resolution mini-/micro-LED displays. However, while the application of square tile-patterned GaN templates formed on sapphire substrates has been demonstrated to improve the emission performance of InGaN-based red LEDs, the impact of template size remains poorly understood. This work addresses this issue by preparing square tile-patterned GaN templates with varying tile dimensions of $500\times 500~\mu $ m to $200\times 200~\mu $ m. The impact of template size on the relaxation state, dislocation density, and surface morphology of the GaN template layers is analyzed systematically, and the emission properties of InGaN-based red mini-LED chips fabricated on these GaN templates are characterized in detail. Experimental results indicate that an optimal template size of $300\times 300~\mu $ m not only promotes lateral relaxation of the underlying layers and mitigates the quantum-confined Stark effect (QCSE), but also enhances crystal quality and reduces dislocation density. Consequently, the LEDs fabricated on this template exhibit higher emission intensity and improved wavelength stability compared to conventional InGaN-based red LEDs grown on planar GaN substrates. A red mini-LED fabricated using the optimal template demonstrates a peak emission wavelength of 634.0 nm at 1 A/cm2, with a 57% increase in peak external quantum efficiency (EQE) compared to the LED grown on the unpatterned template.