E. A. Bulavintseva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
E. A. Bulavintseva has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
A.A. Klimov
1 shared publication- Alexey Kartsev
Bauman Moscow State Technical University, Moscow, 105005, Russia
1 shared publication - Anastasiya V. Gorbatova
MIREA–Russian Technological University, Moscow, Russia
1 shared publication - Andrey A. Guskov
MIREA – Russian Technological University
1 shared publication - Arseniy M. Buryakov
MIREA—Russian Technological University, Moscow, Russia
1 shared publication - Artem Alferyev
MIREA—Russian Technological University, Moscow 119454, Russia
1 shared publication
Latest Publications
- 5 February 2026
- Published by RTU MIREA in Russian Technological Journal
- Vol. 14 (1)
Fabrication of two-dimensional semiconductors on the surface of ferroelectric films by means of gold-assisted mechanical exfoliation
Objectives . The aim of this study is to develop and demonstrate an effective method for obtaining large-area, high-quality monolayers of molybdenum disulfide (MoS 2 ) on the surface of ferroelectric lead zirconate titanate (PZT) films which exhibit pronounced granularity and texturing. Conventional mechanical exfoliation techniques are inefficient for transferring two-dimensional materials onto nonplanar surfaces. This is due to local height variations and substrate granularity which hinder the formation of continuous monolayers and high-defect-density transferred structures. A particular challenge is the transfer onto functional substrates with surface topography characterized by heterogeneities ranging from tens of nanometers to micrometers. Methods . A gold-assisted exfoliation (GAE) method was employed, including: magnetron sputtering of a 50 nm gold film; mechanical delamination of monolayers using thermally cleavable tape; and subsequent gold etching. The characterization was performed using X-ray diffraction, optical confocal microscopy, atomic force microscopy, and second harmonic generation techniques. The efficiency of the transfer process was compared for Si/SiO 2 and PZT substrates. Results . MoS 2 crystallites with areas up to 3000 µm 2 were obtained on PZT and over 65000 µm 2 on standard Si/SiO 2 substrates, both of which exhibit minimal defect densities. Conventional mechanical exfoliation is shown to be unable to ensure transfer onto textured surfaces, whereas the GAE method preserves the monolayer character of the transferred crystallites even on nonplanar substrates. Conclusions . This work demonstrates for the first time the possibility of obtaining large-area, high-quality MoS 2 monolayers on substrates with pronounced grainy and textured structures, such as ferroelectric PZT films, using the gold-assisted exfoliation method. The work also shows that gold-assisted exfoliation is an effective technique for fabricating extended two-dimensional films with controlled morphological and structural properties, including on substrates previously considered unsuitable for such applications.
- 5 February 2026
- Published by RTU MIREA in Russian Technological Journal
- Vol. 14 (1)
Fabrication of two-dimensional semiconductors on the surface of ferroelectric films by means of gold-assisted mechanical exfoliation
Objectives . The aim of this study is to develop and demonstrate an effective method for obtaining large-area, high-quality monolayers of molybdenum disulfide (MoS 2 ) on the surface of ferroelectric lead zirconate titanate (PZT) films which exhibit pronounced granularity and texturing. Conventional mechanical exfoliation techniques are inefficient for transferring two-dimensional materials onto nonplanar surfaces. This is due to local height variations and substrate granularity which hinder the formation of continuous monolayers and high-defect-density transferred structures. A particular challenge is the transfer onto functional substrates with surface topography characterized by heterogeneities ranging from tens of nanometers to micrometers. Methods . A gold-assisted exfoliation (GAE) method was employed, including: magnetron sputtering of a 50 nm gold film; mechanical delamination of monolayers using thermally cleavable tape; and subsequent gold etching. The characterization was performed using X-ray diffraction, optical confocal microscopy, atomic force microscopy, and second harmonic generation techniques. The efficiency of the transfer process was compared for Si/SiO 2 and PZT substrates. Results . MoS 2 crystallites with areas up to 3000 µm 2 were obtained on PZT and over 65000 µm 2 on standard Si/SiO 2 substrates, both of which exhibit minimal defect densities. Conventional mechanical exfoliation is shown to be unable to ensure transfer onto textured surfaces, whereas the GAE method preserves the monolayer character of the transferred crystallites even on nonplanar substrates. Conclusions . This work demonstrates for the first time the possibility of obtaining large-area, high-quality MoS 2 monolayers on substrates with pronounced grainy and textured structures, such as ferroelectric PZT films, using the gold-assisted exfoliation method. The work also shows that gold-assisted exfoliation is an effective technique for fabricating extended two-dimensional films with controlled morphological and structural properties, including on substrates previously considered unsuitable for such applications.
- 1 November 2025
- Published by Kotelnikov Institute of Radioengineering and Electronics of Russian Academy of Sciences in Journal of Radio Electronics
- Vol. 2025 (11)
Sapozhnikov M.V. Spintronic THz emitters based on graphene and antiferromagnets
We investigate terahertz (THz) emission mechanisms in spintronic emitters – Co (3 nm), graphene (Gr)/Co (3 nm), and Co (3 nm)/FeMn (5 nm) – grown on quartz substrates. Magnetic properties were characterized in the longitudinal magneto-optical Kerr effect (MOKE) geometry, and the emission dynamics by time-domain THz spectroscopy (THz-TDS). In Gr/Co, the graphene interface induces perpendicular magnetic anisotropy; the phase of the THz waveforms is invariant with respect to the pumping side at a fixed field polarity, indicating demagnetization-driven emission. Under back-side pumping the amplitude increases by ≈1.5×, whereas front-side excitation reduces it by about a factor of two, consistent with differences in optical/THz absorption and interference. In Co/FeMn, the antiferromagnetic layer imposes pronounced in-plane uniaxial anisotropy and increases coercivity; a phase inversion upon switching the pumping side indicates a dominant inverse spin Hall effect. No exchange bias is observed at the selected thicknesses and without post-annealing. Additionally, an asymmetry of the THz hysteresis loops in Co/FeMn reveals even-in-magnetization contributions to the emission. These results underscore the central role of interface engineering in Co/AFM and Gr/Co stacks for controlling spin-to-charge conversion and optimizing THz-emitter performance.
- 1 November 2025
- Published by Kotelnikov Institute of Radioengineering and Electronics of Russian Academy of Sciences in Journal of Radio Electronics
- Vol. 2025 (11)
Sapozhnikov M.V. Spintronic THz emitters based on graphene and antiferromagnets
We investigate terahertz (THz) emission mechanisms in spintronic emitters – Co (3 nm), graphene (Gr)/Co (3 nm), and Co (3 nm)/FeMn (5 nm) – grown on quartz substrates. Magnetic properties were characterized in the longitudinal magneto-optical Kerr effect (MOKE) geometry, and the emission dynamics by time-domain THz spectroscopy (THz-TDS). In Gr/Co, the graphene interface induces perpendicular magnetic anisotropy; the phase of the THz waveforms is invariant with respect to the pumping side at a fixed field polarity, indicating demagnetization-driven emission. Under back-side pumping the amplitude increases by ≈1.5×, whereas front-side excitation reduces it by about a factor of two, consistent with differences in optical/THz absorption and interference. In Co/FeMn, the antiferromagnetic layer imposes pronounced in-plane uniaxial anisotropy and increases coercivity; a phase inversion upon switching the pumping side indicates a dominant inverse spin Hall effect. No exchange bias is observed at the selected thicknesses and without post-annealing. Additionally, an asymmetry of the THz hysteresis loops in Co/FeMn reveals even-in-magnetization contributions to the emission. These results underscore the central role of interface engineering in Co/AFM and Gr/Co stacks for controlling spin-to-charge conversion and optimizing THz-emitter performance.