Mitsuaki Kato
Mitsuaki Kato has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Akira Kano
Corporate Research and Development Center, Toshiba Corporation
3 shared publicationsKenji Hirohata
Corporate Research and Development Center, Toshiba Corporation
3 shared publicationsAkihiro Goryu
Toshiba Corporation
2 shared publicationsAoi Okada
Toshiba Corporation
1 shared publication- Chiharu Ota
Toshiba Corporation
1 shared publication - Johji Nishio
Toshiba Corporation
1 shared publication
Latest Publications
- 1 September 2022
- Published by Japan Institute of Electronics Packaging in Journal of The Japan Institute of Electronics Packaging
- Vol. 25 (6) , 594-601
Simulation Technologies for Electronics Implementation
- 1 September 2022
- Published by Japan Institute of Electronics Packaging in Journal of The Japan Institute of Electronics Packaging
- Vol. 25 (6) , 594-601
Simulation Technologies for Electronics Implementation
- 16 November 2020
- Published by ASME International
Fatigue Life Law Based on Inelastic Strain Energy Density of Solder Alloys and its Simple Prediction Method
In recent years, a fatigue life law based on inelastic strain energy density as proposed by Morrow has been applied to solder materials. In this study, the effectiveness of the fatigue life law based on inelastic strain energy density was compared with the conventional law based on inelastic strain range. First, the fatigue properties of Sn-Ag-Cu solder alloy were investigated by a torsional fatigue test with strain control. It was found that the stress–strain hysteresis loop arising from inelastic deformation occurred even under a low strain load with a fatigue life of about 1 million cycles. Therefore, as an extension of the low-cycle fatigue test, evaluation was performed using inelastic strain range and inelastic strain energy density. Experimental results show that when fatigue life was evaluated using inelastic strain energy density, a single power law was found over a wide range from the low-cycle region to the high-cycle region, and the validity of the fatigue life law based on inelastic strain energy density was confirmed. Next, a simple prediction method for the fatigue life law based on inelastic strain energy density was examined, taking the physical background into account. Two material constants of the fatigue life law based on the inelastic strain energy density were estimated from the stress–strain curve for a monotonic load and shown to be close to the actual fatigue test results.
- 16 November 2020
- Published by ASME International
Fatigue Life Law Based on Inelastic Strain Energy Density of Solder Alloys and its Simple Prediction Method
In recent years, a fatigue life law based on inelastic strain energy density as proposed by Morrow has been applied to solder materials. In this study, the effectiveness of the fatigue life law based on inelastic strain energy density was compared with the conventional law based on inelastic strain range. First, the fatigue properties of Sn-Ag-Cu solder alloy were investigated by a torsional fatigue test with strain control. It was found that the stress–strain hysteresis loop arising from inelastic deformation occurred even under a low strain load with a fatigue life of about 1 million cycles. Therefore, as an extension of the low-cycle fatigue test, evaluation was performed using inelastic strain range and inelastic strain energy density. Experimental results show that when fatigue life was evaluated using inelastic strain energy density, a single power law was found over a wide range from the low-cycle region to the high-cycle region, and the validity of the fatigue life law based on inelastic strain energy density was confirmed. Next, a simple prediction method for the fatigue life law based on inelastic strain energy density was examined, taking the physical background into account. Two material constants of the fatigue life law based on the inelastic strain energy density were estimated from the stress–strain curve for a monotonic load and shown to be close to the actual fatigue test results.
- 19 July 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 963, 263-267
Dynamics Analysis of Single Shockley Stacking Fault Expansion in 4H-SiC P-i-N Diode Based on Free Energy
Expansion of single Shockley stacking faults (SSFs) during forward current operation is an important issue, because it decreases the reliability of 4H-SiC bipolar devices. In this paper, we propose a method for analyzing SSF dynamics based on free energy under current conduction, temperature, and resolved shear stress conditions. The driving force for dislocation dissociation reactions and formation of SSFs is incorporated into the free energy function, including chemical potential, stacking fault energy, crystallographic energy, gradient energy and elastic strain energy. The net energy gain of the chemical potential was calculated as a function of temperature and current conduction through use of the a TCAD device simulator based on the Boltzmann equation, Poisson equation and the current continuity equation concerning electron and hole distributions with self-consistency. It was confirmed that SSF dynamics can be simulated by the proposed method. It was also found that SSF formation can be attributed to quantum well variation in which electrons in n-type 4H–SiC enter SSF-induced quantum well states to lower the energy of the dislocation system.
- 19 July 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 963, 263-267
Dynamics Analysis of Single Shockley Stacking Fault Expansion in 4H-SiC P-i-N Diode Based on Free Energy
Expansion of single Shockley stacking faults (SSFs) during forward current operation is an important issue, because it decreases the reliability of 4H-SiC bipolar devices. In this paper, we propose a method for analyzing SSF dynamics based on free energy under current conduction, temperature, and resolved shear stress conditions. The driving force for dislocation dissociation reactions and formation of SSFs is incorporated into the free energy function, including chemical potential, stacking fault energy, crystallographic energy, gradient energy and elastic strain energy. The net energy gain of the chemical potential was calculated as a function of temperature and current conduction through use of the a TCAD device simulator based on the Boltzmann equation, Poisson equation and the current continuity equation concerning electron and hole distributions with self-consistency. It was confirmed that SSF dynamics can be simulated by the proposed method. It was also found that SSF formation can be attributed to quantum well variation in which electrons in n-type 4H–SiC enter SSF-induced quantum well states to lower the energy of the dislocation system.
- 3 November 2017
- Published by ASME International
Evaluation Method for Mechanical Stress Dependence of the Electrical Characteristics of SiC MOSFET for Electro-Thermal-Structural Coupled Analysis
Power semiconductor devices such as MOSFET/IGBT and PiN diodes are widely used as basic components for supporting infrastructure in the field of electronics, including in power conversion, industrial equipment, railways, and automobiles. Recently, increasing attention has been paid to silicon carbide (SiC) as a wide-band-gap semiconductor suitable for use in power devices with low loss and high breakdown voltage. However, basic knowledge of the material properties and reliability of SiC devices, and particularly the influence of mechanical stress on device characteristics, is still incomplete. In this paper, we evaluated the effect of mechanical stress on the electrical characteristics of SiC devices. In order to investigate the effect of stress on the SiC device characteristic, we propose a simple evaluation method using four-point bending, which is a classical method capable of applying uniaxial stress to a device. With this method, we evaluated the stress in a SiC device using residual stress measurement by Raman spectroscopy and stress simulation based on the finite element method. Our proposed experimental method is as follows. First, the SiC device was bonded with AuGe solder to a metal plate [phosphor bronze; Young’s modulus: 105 GPa; Poisson’s ratio: 0.33; dimensions: 100 mm (W) × 12 mm (L) × 2 mm (T)], and aluminum wire (wire radius: 200 μm) was also bonded to the device. Second, the prepared device was placed on the specially designed four-point bending apparatus for mechanical stress experiments. Finally, the sample was bent in compression or tension in the in-plane direction by the four-point system. The SiC device was subjected to compression or tensile stress via the metal plate. The electrical characteristics of the SiC-MOSFET were measured with a curve tracer in our proposed system. Id−Vds characteristics changed linearly as stress was applied to the device. As a result, the on-resistance was increased by 7.6% by applying a tensile stress of 300 MPa and was decreased by 1.0% by applying a compressive stress of 100 MPa at room temperature, respectively. A power device circuit with multiple chips was also simulated by SPICE based on the experimental results to confirm the effects of stress on SiC devices in a power module. Simulated MOSFET model contains stress factors obtained from experimental results. The circuit was simulated by electro-thermal coupled analysis using a one-dimensional model of the electric circuit and thermal circuit constructed in SPICE. The results show that the proposed method is powerful simulation method for power device design.
- 3 November 2017
- Published by ASME International
Evaluation Method for Mechanical Stress Dependence of the Electrical Characteristics of SiC MOSFET for Electro-Thermal-Structural Coupled Analysis
Power semiconductor devices such as MOSFET/IGBT and PiN diodes are widely used as basic components for supporting infrastructure in the field of electronics, including in power conversion, industrial equipment, railways, and automobiles. Recently, increasing attention has been paid to silicon carbide (SiC) as a wide-band-gap semiconductor suitable for use in power devices with low loss and high breakdown voltage. However, basic knowledge of the material properties and reliability of SiC devices, and particularly the influence of mechanical stress on device characteristics, is still incomplete. In this paper, we evaluated the effect of mechanical stress on the electrical characteristics of SiC devices. In order to investigate the effect of stress on the SiC device characteristic, we propose a simple evaluation method using four-point bending, which is a classical method capable of applying uniaxial stress to a device. With this method, we evaluated the stress in a SiC device using residual stress measurement by Raman spectroscopy and stress simulation based on the finite element method. Our proposed experimental method is as follows. First, the SiC device was bonded with AuGe solder to a metal plate [phosphor bronze; Young’s modulus: 105 GPa; Poisson’s ratio: 0.33; dimensions: 100 mm (W) × 12 mm (L) × 2 mm (T)], and aluminum wire (wire radius: 200 μm) was also bonded to the device. Second, the prepared device was placed on the specially designed four-point bending apparatus for mechanical stress experiments. Finally, the sample was bent in compression or tension in the in-plane direction by the four-point system. The SiC device was subjected to compression or tensile stress via the metal plate. The electrical characteristics of the SiC-MOSFET were measured with a curve tracer in our proposed system. Id−Vds characteristics changed linearly as stress was applied to the device. As a result, the on-resistance was increased by 7.6% by applying a tensile stress of 300 MPa and was decreased by 1.0% by applying a compressive stress of 100 MPa at room temperature, respectively. A power device circuit with multiple chips was also simulated by SPICE based on the experimental results to confirm the effects of stress on SiC devices in a power module. Simulated MOSFET model contains stress factors obtained from experimental results. The circuit was simulated by electro-thermal coupled analysis using a one-dimensional model of the electric circuit and thermal circuit constructed in SPICE. The results show that the proposed method is powerful simulation method for power device design.