Chaoyue Fei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chaoyue Fei has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bram Vanderborght
Brubotics, Vrije Universiteit Brussel and Imec, Elsene, Belgium
2 shared publications - Greet Van de Perre
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
2 shared publications - Hafsa Nouhi
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
2 shared publications Ann Nowe
Vrije Universiteit Brussel
1 shared publication- Bas Boom
IMEC
1 shared publication - Frederik Ostyn
Department of Electromechanical, Systems and Metal Engineering, Ghent University, Ghent, Belgium
1 shared publication
Latest Publications
- Open Access
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 9110-9123
Optimizing Link Flexibility for Safety and Dynamic Performance for Collaborative Manipulators
Cobots are designed to work in close collaboration with humans. To ensure safety in shared workspaces, ISO/TS 15066 imposes limits on the collaborative robot speeds to limit the impact forces during collisions. These limits depend on robot design, including inertia. Flexible link manipulators combine the advantage of lightweight design and the introduction of an elastic element, which is promising in the context of collaborative robots. However, reduced stiffness affects dynamic performance. As trade-offs between link flexibility for safety and dynamic performance remain unclear, this paper investigates how undesired side effects of flexibility relate to the positive aspects of compliance and lightweightness. To investigate the effect of flexibility on both safety towards a human and controlled manipulator dynamics, a generic simulation framework was designed. Safety is assessed by a simulation study on the influence of varying geometrical parameters on impact force at collision with a human head, after which the corresponding maximum allowable end-effector velocities per ISO/TS 15066 threshold were derived. To analyze control performance, a generic controller was implemented, consisting of a PID with direct strain vibration control, with gains optimized for each link design. The resulting end-effector tracking performance during point-to-point motion is evaluated. Based on these results, a co-design methodology was proposed to optimize link geometry and control gains for the fastest possible, yet safe motion for a given task. The effectiveness of the method was experimentally validated to assess whether optimal link stiffness and controller gains yield the desired dynamic performance while respecting ISO safety thresholds.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 9110-9123
Open AccessOptimizing Link Flexibility for Safety and Dynamic Performance for Collaborative Manipulators
Cobots are designed to work in close collaboration with humans. To ensure safety in shared workspaces, ISO/TS 15066 imposes limits on the collaborative robot speeds to limit the impact forces during collisions. These limits depend on robot design, including inertia. Flexible link manipulators combine the advantage of lightweight design and the introduction of an elastic element, which is promising in the context of collaborative robots. However, reduced stiffness affects dynamic performance. As trade-offs between link flexibility for safety and dynamic performance remain unclear, this paper investigates how undesired side effects of flexibility relate to the positive aspects of compliance and lightweightness. To investigate the effect of flexibility on both safety towards a human and controlled manipulator dynamics, a generic simulation framework was designed. Safety is assessed by a simulation study on the influence of varying geometrical parameters on impact force at collision with a human head, after which the corresponding maximum allowable end-effector velocities per ISO/TS 15066 threshold were derived. To analyze control performance, a generic controller was implemented, consisting of a PID with direct strain vibration control, with gains optimized for each link design. The resulting end-effector tracking performance during point-to-point motion is evaluated. Based on these results, a co-design methodology was proposed to optimize link geometry and control gains for the fastest possible, yet safe motion for a given task. The effectiveness of the method was experimentally validated to assess whether optimal link stiffness and controller gains yield the desired dynamic performance while respecting ISO safety thresholds.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Field Robotics
- Vol. 3, 861-877
Dual-Modal Motion Planning and Control for Robotic Orchard Pruning Under Uncertainties
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Field Robotics
- Vol. 3, 861-877
Dual-Modal Motion Planning and Control for Robotic Orchard Pruning Under Uncertainties
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 145-152
Flexible-Link Velocity-Bounding Proxy Based Sliding Mode Control
This letter proposes a control strategy for flexible link manipulators preserving high tracking accuracy in free motion, while ensuring smooth and safe behavior in scenarios involving physical interaction or large positional errors, based on the VB-PSMC. The scheme is extended to compensate for the manipulator’s flexural dynamics, resulting in a nested control scheme where damping of the induced oscillations is achieved by a model-free proportional strain feedback while gravity induced deflections are counteracted by a feed-forward term based on a quasi-static Euler-Bernoulli beam model. A convergence study on the modified sliding manifold and a stability analysis of the closed-loop system is provided. The performance of the controller was evaluated experimentally and compared against other control strategies such as PSMC and torque limited PD control. The results demonstrate the controller’s accurate end effector tracking in free motion, while achieving compliant behavior during contact, by efficiently handling the link’s inherent flexibility leading up to a 32% reduction in interaction force. In addition, studying the FL-VB-PSMC response after releasing contact demonstrated the smooth and vibration-free recovery even for large position errors.
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 145-152
Flexible-Link Velocity-Bounding Proxy Based Sliding Mode Control
This letter proposes a control strategy for flexible link manipulators preserving high tracking accuracy in free motion, while ensuring smooth and safe behavior in scenarios involving physical interaction or large positional errors, based on the VB-PSMC. The scheme is extended to compensate for the manipulator’s flexural dynamics, resulting in a nested control scheme where damping of the induced oscillations is achieved by a model-free proportional strain feedback while gravity induced deflections are counteracted by a feed-forward term based on a quasi-static Euler-Bernoulli beam model. A convergence study on the modified sliding manifold and a stability analysis of the closed-loop system is provided. The performance of the controller was evaluated experimentally and compared against other control strategies such as PSMC and torque limited PD control. The results demonstrate the controller’s accurate end effector tracking in free motion, while achieving compliant behavior during contact, by efficiently handling the link’s inherent flexibility leading up to a 32% reduction in interaction force. In addition, studying the FL-VB-PSMC response after releasing contact demonstrated the smooth and vibration-free recovery even for large position errors.