Prabhakar Kr. Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Prabhakar Kr. Singh has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Probir Saha
Indian Institute of Technology Patna, Patna, India
3 shared publications - Akash Kanji
Jadavpur University, Kolkata, India
1 shared publication - Akash Mukhopadhyay
Indian Institute of Technology Patna Advanced Manufacturing Laboratory, Department of Mechanical Engineering ; Energy and Environment Directorate
1 shared publication - Akash Mukhopadhyay
Indian Institute of Technology Patna, Bihta, Patna, Bihar, India
1 shared publication - Avirup Das
Jadavpur University, Kolkata, India
1 shared publication - Piyush Kumar Sinha
Indian Institute of Technology Patna, Patna, India
1 shared publication
Latest Publications
- 28 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 11661-11680
Single-track thermo-viscoplastic modeling of friction stir deposition using physics-informed neural networks
- 28 September 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 11661-11680
Single-track thermo-viscoplastic modeling of friction stir deposition using physics-informed neural networks
- 21 November 2025
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 148 (1)
Effect of Feeding Strategy on the Microstructure and Microhardness in Friction Stir-Based Additive Manufacturing of Aluminum Alloy Powder
Powder-based friction stir additive manufacturing employs various methods to deliver powder to the deposition zone, which can influence the deposits' microstructure by altering how the powder interacts with the tool. However, this area has not been extensively explored in existing research. To investigate this, AA6061 powder was deposited using two powder-based techniques: additive friction stir deposition (P-AFSD) and additive friction stir processing (AFSP). The resulting microstructural evolution was subsequently analyzed to establish correlations with each method's respective deposit formation mechanisms. The AFSP microstructure exhibited ∼20% more recrystallized grains than P-AFSD but contained ∼1% fewer high-angle grain boundaries. This may be due to the powder material undergoing deposition and recrystallization under relatively higher temperature and deformation conditions during AFSP, followed by additional strain as most of the tool's front and entire rear section passed over the deposited material. Texture evolution was examined using pole figures and orientation distribution functions. The initial extrusion of partially plasticized material through the central hole of the P-AFSD tool led to a strong presence of A-type textures and the absence of any plane strain component. Moreover, the average Vicker's microhardness was 78 HV for P-AFSD and 65 HV for AFSP.
- 21 November 2025
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 148 (1)
Effect of Feeding Strategy on the Microstructure and Microhardness in Friction Stir-Based Additive Manufacturing of Aluminum Alloy Powder
Powder-based friction stir additive manufacturing employs various methods to deliver powder to the deposition zone, which can influence the deposits' microstructure by altering how the powder interacts with the tool. However, this area has not been extensively explored in existing research. To investigate this, AA6061 powder was deposited using two powder-based techniques: additive friction stir deposition (P-AFSD) and additive friction stir processing (AFSP). The resulting microstructural evolution was subsequently analyzed to establish correlations with each method's respective deposit formation mechanisms. The AFSP microstructure exhibited ∼20% more recrystallized grains than P-AFSD but contained ∼1% fewer high-angle grain boundaries. This may be due to the powder material undergoing deposition and recrystallization under relatively higher temperature and deformation conditions during AFSP, followed by additional strain as most of the tool's front and entire rear section passed over the deposited material. Texture evolution was examined using pole figures and orientation distribution functions. The initial extrusion of partially plasticized material through the central hole of the P-AFSD tool led to a strong presence of A-type textures and the absence of any plane strain component. Moreover, the average Vicker's microhardness was 78 HV for P-AFSD and 65 HV for AFSP.
- Open Access
- 1 January 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (1) , 57-62
Experimental investigation of novel powder bed friction stir process for AZ31B Mg alloy
The current work focused on the process response and mechanical properties variation of the AZ31B powder deposit made by an in-house developed process at a laboratory scale named Powder Bed Friction Stir (PBFS). The PBFS process employs friction stirring as a heating source instead of a laser or electron beam, as in powder bed fusion. Despite the tremendous effectiveness of Mg alloys for structural applications, a suitable route is still being searched for. The motivation of the current work is to explore the potential of the newly developed PBFS process for AZ31B Mg alloy deposition. With 1200rpm and 360 mm/min, the experimentation was carried out using the CPF tool to make a 7mm thick deposit on the AZ31B Mg plate. The process response and mechanical properties were studied to compare the result with wrought Mg alloy.
- 1 January 2023
- Published by Central Manufacturing Technology Institute in Manufacturing Technology Today (MTT)
- Vol. 22 (1) , 57-62
Open AccessExperimental investigation of novel powder bed friction stir process for AZ31B Mg alloy
The current work focused on the process response and mechanical properties variation of the AZ31B powder deposit made by an in-house developed process at a laboratory scale named Powder Bed Friction Stir (PBFS). The PBFS process employs friction stirring as a heating source instead of a laser or electron beam, as in powder bed fusion. Despite the tremendous effectiveness of Mg alloys for structural applications, a suitable route is still being searched for. The motivation of the current work is to explore the potential of the newly developed PBFS process for AZ31B Mg alloy deposition. With 1200rpm and 360 mm/min, the experimentation was carried out using the CPF tool to make a 7mm thick deposit on the AZ31B Mg plate. The process response and mechanical properties were studied to compare the result with wrought Mg alloy.