Mingwei Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mingwei Gao has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Caili Dai
China University of Petroleum (East China)
3 shared publications - Mingwei Zhao
China University of Petroleum (East China)
2 shared publications - Xiangyu Wang
Faculty of Technology, Bielefeld University, Bielefeld, Germany
2 shared publications - Bao Li
Jilin University
1 shared publication - Bo Wu
Beijing National Laboratory for Molecular Sciences, Key Laboratory of Molecular Nanostructure and Nanotechnology, Institute of Chemistry, Chinese Academy of Sciences, Beijing, China
1 shared publication - Changlong Liu
School of Science, Tianjin University, Tianjin University, Tianjin 300072, P.R. China, Tianjin, CHINA
1 shared publication
Latest Publications
- 24 August 2022
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 366, 120159
Intermolecular interactions induced desulfurization/denitrification of oil with deep eutectic solvents
- 24 August 2022
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 366, 120159
Intermolecular interactions induced desulfurization/denitrification of oil with deep eutectic solvents
- 9 June 2022
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 360, 119563
Preparation and thickening mechanism of copolymer fluorinated thickeners in supercritical CO2
- 9 June 2022
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 360, 119563
Preparation and thickening mechanism of copolymer fluorinated thickeners in supercritical CO2
- Open Access
- 5 May 2022
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 9
Grain Size and Macrosegregation Control of Large-Sized AA2219 Billets by Internal Electromagnetic Stirring in DC Casting
This work focuses on the effect of internal electromagnetic stirring (IEMS) on grain size and macrosegregation in direct-chill (DC) casting of an AA2219 billet with a diameter of 880 mm. The IEMS process has been applied to provide forced convection within the solidifying melt to achieve an efficient reduction of mean grain size and alleviate the formation of macrosegregation. Two casting electromagnetic parameters (the stirring electric current and frequency) of the IEMS process were applied to assess the uniformity of the microstructure and macrosegregation of the billet. The experimental results show that finer and more uniform grains in the billet prepared by the IEMS process than those of traditional DC casting have been observed. The IEMS process has a great influence on the improvement of the macrosegregation, but the greater electromagnetic field would result in worse macrosegregation in the center of the billet.
- 5 May 2022
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 9
Open AccessGrain Size and Macrosegregation Control of Large-Sized AA2219 Billets by Internal Electromagnetic Stirring in DC Casting
This work focuses on the effect of internal electromagnetic stirring (IEMS) on grain size and macrosegregation in direct-chill (DC) casting of an AA2219 billet with a diameter of 880 mm. The IEMS process has been applied to provide forced convection within the solidifying melt to achieve an efficient reduction of mean grain size and alleviate the formation of macrosegregation. Two casting electromagnetic parameters (the stirring electric current and frequency) of the IEMS process were applied to assess the uniformity of the microstructure and macrosegregation of the billet. The experimental results show that finer and more uniform grains in the billet prepared by the IEMS process than those of traditional DC casting have been observed. The IEMS process has a great influence on the improvement of the macrosegregation, but the greater electromagnetic field would result in worse macrosegregation in the center of the billet.
- 17 October 2017
- Published by Society of Petroleum Engineers (SPE)
Experimental Investigation on a Novel Organic-Inorganic Crosslinked Polymer Gel for Water Control in Ultra-High Temperature Reservoirs
This article presents a novel organic-inorganic crosslinked polymer gel, which uses resin-silicate as the organic-inorganic crosslinker, to extend the temperature limitations of currently used polymer gels for water control in mature oilfields. The gelation performances, including gelation time, gel strength and thermal stability, were studied, and the optimum composition was selected by study of gelation performances. Results show that with increase of the concentrations of components, gelation time became shorter and gel strength was improved. And the gel system was stable after 90 days at 140 °C. The optimum composition of the gel system was selected as: 4~7 wt% resin and 2~5 wt% silicate with 0.1~0.3 wt% polymer. Meanwhile, differential scanning calorimetry (DSC) measurement was used to investigate the maximum tolerated temperature of the gel. The results showed that the chemical bonds of the gel began to break at 156 °C, which indicated that the gel can resist high temperature up to 156 °C. At last, environmental scanning electron microscopy (ESEM) microstructure and fourier transform infrared spectroscopy (FTIR) spectrum of the gel were studied to analyze the gelation process and investigate the mechanism for temperature resistance. The three-dimensional network microstructure of the resin-silicate crosslinked polymer gel was more compact and more uniform than the gel prepared without silicate. The formation of silicon-oxygen bonds (Si-O) increased the crosslinking density and temperature tolerance of the gel system.
- 17 October 2017
- Published by Society of Petroleum Engineers (SPE)
Experimental Investigation on a Novel Organic-Inorganic Crosslinked Polymer Gel for Water Control in Ultra-High Temperature Reservoirs
This article presents a novel organic-inorganic crosslinked polymer gel, which uses resin-silicate as the organic-inorganic crosslinker, to extend the temperature limitations of currently used polymer gels for water control in mature oilfields. The gelation performances, including gelation time, gel strength and thermal stability, were studied, and the optimum composition was selected by study of gelation performances. Results show that with increase of the concentrations of components, gelation time became shorter and gel strength was improved. And the gel system was stable after 90 days at 140 °C. The optimum composition of the gel system was selected as: 4~7 wt% resin and 2~5 wt% silicate with 0.1~0.3 wt% polymer. Meanwhile, differential scanning calorimetry (DSC) measurement was used to investigate the maximum tolerated temperature of the gel. The results showed that the chemical bonds of the gel began to break at 156 °C, which indicated that the gel can resist high temperature up to 156 °C. At last, environmental scanning electron microscopy (ESEM) microstructure and fourier transform infrared spectroscopy (FTIR) spectrum of the gel were studied to analyze the gelation process and investigate the mechanism for temperature resistance. The three-dimensional network microstructure of the resin-silicate crosslinked polymer gel was more compact and more uniform than the gel prepared without silicate. The formation of silicon-oxygen bonds (Si-O) increased the crosslinking density and temperature tolerance of the gel system.