Peter Gaso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Peter Gaso has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Dusan Pudis
Univ. of Žilina (Slovakia)
3 shared publications - Matej Goraus
Department of Physics, Faculty of Electrical Engineering and Information Technology, University of Zilina, Univerzitna 1, 01026 Zilina, Slovakia
2 shared publications - Dana Seyringer
Research Centre for Microtechnology, Vorarlberg University of Applied Sciences (FHV), Hochschulstraße 1, 6850 Dornbirn, Austria
1 shared publication - Daniel Jandura
Department of Physics, Faculty of Electrical Engineering and Information Technology, University of Zilina, Univerzitna 1, 01026 Zilina, Slovakia
1 shared publication - Fadi Dohnal
Research Centre for Microtechnology, Vorarlberg University of Applied Sciences (FHV), Hochschulstraße 1, 6850 Dornbirn, Austria
1 shared publication - Frantisek Uherek
Faculty of Electrical Engineering and Information Technology, Institute of Electronics and Photonics, Slovak University of Technology in Bratislava, Ilkovicova 3, 81219 Bratislava, Slovakia
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2778 (1) , 030010
Design of 16-channel, 100-GHz multimode polymer-based AWG
We present design of planar 16-channel, 100-GHz multi-mode polymer-based AWG. This AWG was designed for central wavelength of 1550 nm applying AWG-Parameters to
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2778 (1) , 030010
Open AccessDesign of 16-channel, 100-GHz multimode polymer-based AWG
We present design of planar 16-channel, 100-GHz multi-mode polymer-based AWG. This AWG was designed for central wavelength of 1550 nm applying AWG-Parameters to
- 30 May 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10249, 1024903
Polymer ring resonator based devices prepared by DLW
In this paper, the fabrication method of waveguide structures and devices as ring resonators for different waveguide applications based on polymer material is presented. The structures were designed in computer-aided design (CAD) software and two-photon polymerization lithography system was used for preparation of desired devices. Morphological properties of prepared devices were investigated using scanning electron microscope (SEM) and confocal microscope. Finally, we performed measurement of optical spectrum characteristics in telecommunication wavelengths range. The results corresponds to calculated parameters. Final polymer devices are promising for lab on a chip and sensing applications due to unique elastic and chemical properties.
- 30 May 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10249, 1024903
Polymer ring resonator based devices prepared by DLW
In this paper, the fabrication method of waveguide structures and devices as ring resonators for different waveguide applications based on polymer material is presented. The structures were designed in computer-aided design (CAD) software and two-photon polymerization lithography system was used for preparation of desired devices. Morphological properties of prepared devices were investigated using scanning electron microscope (SEM) and confocal microscope. Finally, we performed measurement of optical spectrum characteristics in telecommunication wavelengths range. The results corresponds to calculated parameters. Final polymer devices are promising for lab on a chip and sensing applications due to unique elastic and chemical properties.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
LEDs with photonic crystal and quasicrystal investigated in near and far field
It was confirmed that photonic crystals (PhC) have the considerable effect on enhancement of extraction efficiency of light emitting diodes (LED) by minimizing the total internal reflection of the light escaping the LED chip. The enhancement of the extraction efficiency requires a structure design that optimizes the interaction of the guided modes with the PhCs. It strongly depends on the structure parameters as depth, period and filling factor. On the other side, choice of PhC geometry plays important role in determining of far-field radiation pattern diagram of the LED. From the point of structure shape and geometry, different PhC and photonic quasicrystals (PQC) were investigated. The PQCs with high level of symmetry produce less directional emission and it favors the PQC structure for application in LED.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
LEDs with photonic crystal and quasicrystal investigated in near and far field
It was confirmed that photonic crystals (PhC) have the considerable effect on enhancement of extraction efficiency of light emitting diodes (LED) by minimizing the total internal reflection of the light escaping the LED chip. The enhancement of the extraction efficiency requires a structure design that optimizes the interaction of the guided modes with the PhCs. It strongly depends on the structure parameters as depth, period and filling factor. On the other side, choice of PhC geometry plays important role in determining of far-field radiation pattern diagram of the LED. From the point of structure shape and geometry, different PhC and photonic quasicrystals (PQC) were investigated. The PQCs with high level of symmetry produce less directional emission and it favors the PQC structure for application in LED.