Edzrol Niza Mohamad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Edzrol Niza Mohamad has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Zuradzman Mohamad Razlan
Universiti Malaysia Perlis
2 shared publications Fazreena Nadia Md Akhir
Malaysia-Japan International Institute of Technology (MJIIT), Universiti Teknologi Malaysia (UTM), Jalan Sultan Yahya Petra, 54100 Kuala Lumpur, Malaysia
1 shared publication- Hiroaki Tanaka
Confocal Science Inc
1 shared publication Hirofumi Hara
Department of Biotechnology, Laboratory of Microbial Ecotechnology, Graduate School of Agricultural and Life Sciences, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8654 Japan
1 shared publicationIchiro Moriwaki
Kyoto Institute of Technology
1 shared publication- Kamyar Shameli
School of Medicine, Institute of Virology, Technical University of Munich, Munich, Germany
1 shared publication
Latest Publications
- 13 June 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 145 (3-4) , 1-15
Effects of nozzle mobility on fibre formation in double-nozzle electrospinning designs
- 13 June 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 145 (3-4) , 1-15
Effects of nozzle mobility on fibre formation in double-nozzle electrospinning designs
- Open Access
- 11 March 2026
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 27 (5) , 2199-2245
From Single-Nozzle to Multi-Nozzle Electrospinning: A Comparative Manufacturability Perspective on 3D Electrospun Structures
Electrospinning has evolved from producing two-dimensional nanofiber mats to forming three-dimensional electrospun (3D ES) structures with improved mechanical integrity and functional performance. However, scalable and controllable fabrication of 3D ES structures remains challenging. This review provides a quantitative and mechanism-oriented comparison of major fabrication strategies, including single-nozzle electrospinning (SN), electric field manipulation (EFM), mold-based methods (MBM), near-field electrospinning (NF), hybrid electrospinning–3D printing methods (HBM), controlled deposition systems (CDM), and multi-nozzle electrospinning (MN). Reported operating parameters span applied voltages from 0.1 to 65 kV, working distances from 0.1 to 385 mm, and material delivery rates from 0.006 to 96 mL/h. SN-based and mold-assisted approaches demonstrate the feasibility of forming 3D ES structures under single-jet conditions and low flow rates (typically < 7 mL/h), but their scalability is inherently limited. NF achieves high positional accuracy at short working distances (≤ 80 mm) and low voltages (≤ 8 kV), though its narrow process window restricts large-area fabrication. In contrast, MN electrospinning enables the highest throughput, with nozzle counts ranging from 2 to 72 and fiber diameters as small as 66 nm. Importantly, successful 3D structure formation using single-nozzle configurations confirms that the fundamental electrohydrodynamic mechanisms for three-dimensional growth already exist, implying that MN systems operating at higher throughput possess greater potential for scalable 3D ES fabrication. Despite this, MN performance remains highly sensitive to inter-nozzle spacing, electric-field uniformity, and jet–jet electrostatic interactions, which continue to limit deposition uniformity and mechanical robustness.
- 11 March 2026
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 27 (5) , 2199-2245
Open AccessFrom Single-Nozzle to Multi-Nozzle Electrospinning: A Comparative Manufacturability Perspective on 3D Electrospun Structures
Electrospinning has evolved from producing two-dimensional nanofiber mats to forming three-dimensional electrospun (3D ES) structures with improved mechanical integrity and functional performance. However, scalable and controllable fabrication of 3D ES structures remains challenging. This review provides a quantitative and mechanism-oriented comparison of major fabrication strategies, including single-nozzle electrospinning (SN), electric field manipulation (EFM), mold-based methods (MBM), near-field electrospinning (NF), hybrid electrospinning–3D printing methods (HBM), controlled deposition systems (CDM), and multi-nozzle electrospinning (MN). Reported operating parameters span applied voltages from 0.1 to 65 kV, working distances from 0.1 to 385 mm, and material delivery rates from 0.006 to 96 mL/h. SN-based and mold-assisted approaches demonstrate the feasibility of forming 3D ES structures under single-jet conditions and low flow rates (typically < 7 mL/h), but their scalability is inherently limited. NF achieves high positional accuracy at short working distances (≤ 80 mm) and low voltages (≤ 8 kV), though its narrow process window restricts large-area fabrication. In contrast, MN electrospinning enables the highest throughput, with nozzle counts ranging from 2 to 72 and fiber diameters as small as 66 nm. Importantly, successful 3D structure formation using single-nozzle configurations confirms that the fundamental electrohydrodynamic mechanisms for three-dimensional growth already exist, implying that MN systems operating at higher throughput possess greater potential for scalable 3D ES fabrication. Despite this, MN performance remains highly sensitive to inter-nozzle spacing, electric-field uniformity, and jet–jet electrostatic interactions, which continue to limit deposition uniformity and mechanical robustness.
- Open Access
- 25 January 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Sciences and Engineering Technology
- Vol. 26 (1) , 15-22
Identification of flavour chemicals and potentially harmful compounds in refill e-liquids sold in Malaysia
E-cigarette has been marketed over years as one of alternative smoking cessation aid offered for consumer worldwide. The addition of flavouring in e-liquid has become a major factor that contributes to the appeal of using e-cigarette among a non-smoker and youngster has raised concerns due to possible risk and hazard outcomes in daily usage is remain unclear to date. In order to fully understand the e-cigarette attributes towards human health and environment; 17 e-liquid products locally sold were bought and analysed by gas chromatography-mass spectrometer (GC-MS) in order to determine the chemical constituent of e-liquid, especially the flavouring additive. A total of 19 out of 41 identified chemical compounds were detected as a new flavouring agent used in e-liquid products since there was no previous report on this. Many of the flavour chemicals possessed a risk of inhalation toxicity because they were classified as corrosive and/or irritant, with only a few having acute toxicity and the potential to cause cancer. Moreover, several chemical compounds to be concerned such as stimulant as well as opioid types were unexpectedly identified in the e-liquid. Thus, this finding indicate that the chemical constituent of e-liquid contained unknown risk of toxicity and further research is needed to fully understand the possibility of adverse effect in using e-cigarette.
- 25 January 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Sciences and Engineering Technology
- Vol. 26 (1) , 15-22
Open AccessIdentification of flavour chemicals and potentially harmful compounds in refill e-liquids sold in Malaysia
E-cigarette has been marketed over years as one of alternative smoking cessation aid offered for consumer worldwide. The addition of flavouring in e-liquid has become a major factor that contributes to the appeal of using e-cigarette among a non-smoker and youngster has raised concerns due to possible risk and hazard outcomes in daily usage is remain unclear to date. In order to fully understand the e-cigarette attributes towards human health and environment; 17 e-liquid products locally sold were bought and analysed by gas chromatography-mass spectrometer (GC-MS) in order to determine the chemical constituent of e-liquid, especially the flavouring additive. A total of 19 out of 41 identified chemical compounds were detected as a new flavouring agent used in e-liquid products since there was no previous report on this. Many of the flavour chemicals possessed a risk of inhalation toxicity because they were classified as corrosive and/or irritant, with only a few having acute toxicity and the potential to cause cancer. Moreover, several chemical compounds to be concerned such as stimulant as well as opioid types were unexpectedly identified in the e-liquid. Thus, this finding indicate that the chemical constituent of e-liquid contained unknown risk of toxicity and further research is needed to fully understand the possibility of adverse effect in using e-cigarette.
- Open Access
- 1 January 2002
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Machine Design and Tribology Division meeting in JSME
- Vol. 2002.2, 63-66
Tooth Bearing Evaluation System for Hypoid Gears using Artificial Intelligence
- 1 January 2002
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Machine Design and Tribology Division meeting in JSME
- Vol. 2002.2, 63-66
Open AccessTooth Bearing Evaluation System for Hypoid Gears using Artificial Intelligence