Romuald Jolivot
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Romuald Jolivot has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Waleed Soliman Mohammed
Center of Research in Optoelectronics, Communication and Control Systems (BU-CROCCS), School of Engineering, Bangkok University, Pathumthani 12120, Thailand
2 shared publications - Chamras Promptmas
Department of Biomedical Engineering, Faculty of Engineering, Mahidol University, Nakhon Pathom, Thailand
1 shared publication Dorra Nouri
Lab. PRISME, Univ. d'Orléans (France)
1 shared publication- Franck Marzani
Université de Bourgogne
1 shared publication Hironmay Deb
BU-CROCCS, School of Engineering, Bangkok University, Pathumthani, Thailand
1 shared publication- Michael Komodromos
Department of Electrical Engineering, Frederick University, 199291 Nicosia, Nicosia Cyprus
1 shared publication
Latest Publications
- 1 December 2020
- Published by Elsevier in Optics & Laser Technology
- Vol. 132, 106517
Enhanced sensitivity of guided mode resonance sensor through super-mode excitation at near cut-off diffraction
- 1 December 2020
- Published by Elsevier in Optics & Laser Technology
- Vol. 132, 106517
Enhanced sensitivity of guided mode resonance sensor through super-mode excitation at near cut-off diffraction
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 373-376
Optical beam shaping design through optimization of a radial phase mask
Laser beams shaped into flattop are widely used in various industrial and medical applications. There are various approaches to produce a flattop beam from a Gaussian beam. In this paper, a novel approach called Method of Projection is used to optimize a single element Radial phase mask to obtain flattop output beam. In this approach, Henkel transform and cross-correlation in iterative loop is used to optimize the parameters. Following this approach, a suitable phase mask pattern is obtained in grayscale. The simulated results are compared with target intensity profile through cross-correlation and further optimized to reach certain goodness value. The designed algorithm is a single element radially symmetric phase mask, which is low cost, alignment-free and robust. Hence, the proposed approach reduces the number of components required to develop a flattop output.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 373-376
Optical beam shaping design through optimization of a radial phase mask
Laser beams shaped into flattop are widely used in various industrial and medical applications. There are various approaches to produce a flattop beam from a Gaussian beam. In this paper, a novel approach called Method of Projection is used to optimize a single element Radial phase mask to obtain flattop output beam. In this approach, Henkel transform and cross-correlation in iterative loop is used to optimize the parameters. Following this approach, a suitable phase mask pattern is obtained in grayscale. The simulated results are compared with target intensity profile through cross-correlation and further optimized to reach certain goodness value. The designed algorithm is a single element radially symmetric phase mask, which is low cost, alignment-free and robust. Hence, the proposed approach reduces the number of components required to develop a flattop output.
- Open Access
- 13 March 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8669, 866923
Colour and multispectral imaging for wound healing evaluation in the context of a comparative preclinical study
Accurate wound assessment is a critical task for patient care and health cost reduction at hospital but even still worse in the context of clinical studies in laboratory. This task, completely devoted to nurses, still relies on manual and tedious practices. Wound shape is measured with rules, tracing papers or rarely with alginate castings and serum injection. The wound tissues proportion is also estimated by a qualitative visual assessment based on the red-yellow-black code. Further to our preceding works on wound 3D complete assessment using a simple freehanded digital camera, we explore here the adaptation of this tool to wounds artificially created for experimentation purposes. It results that tissue uniformity and flatness leads to a simplified approach but requires multispectral imaging for enhanced wound delineation. We demonstrate that, in this context, a simple active contour method can successfully replace more complex tools such as SVM supervised classification, as no training step is required and that one shot is enough to deal with perspective projection errors. Moreover, involving all the spectral response of the tissue and not only RGB components provides a higher discrimination for separating healed epithelial tissue from granulation tissue. This research work is part of a comparative preclinical study on healing wounds. It aims to compare the efficiency of specific medical honeys with classical pharmaceuticals for wound care. Results revealed that medical honey competes with more expensive pharmaceuticals.
- 13 March 2013
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8669, 866923
Open AccessColour and multispectral imaging for wound healing evaluation in the context of a comparative preclinical study
Accurate wound assessment is a critical task for patient care and health cost reduction at hospital but even still worse in the context of clinical studies in laboratory. This task, completely devoted to nurses, still relies on manual and tedious practices. Wound shape is measured with rules, tracing papers or rarely with alginate castings and serum injection. The wound tissues proportion is also estimated by a qualitative visual assessment based on the red-yellow-black code. Further to our preceding works on wound 3D complete assessment using a simple freehanded digital camera, we explore here the adaptation of this tool to wounds artificially created for experimentation purposes. It results that tissue uniformity and flatness leads to a simplified approach but requires multispectral imaging for enhanced wound delineation. We demonstrate that, in this context, a simple active contour method can successfully replace more complex tools such as SVM supervised classification, as no training step is required and that one shot is enough to deal with perspective projection errors. Moreover, involving all the spectral response of the tissue and not only RGB components provides a higher discrimination for separating healed epithelial tissue from granulation tissue. This research work is part of a comparative preclinical study on healing wounds. It aims to compare the efficiency of specific medical honeys with classical pharmaceuticals for wound care. Results revealed that medical honey competes with more expensive pharmaceuticals.