Jan Halvor Nordlien
Research Subjects
Jan Halvor Nordlien has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Eva Anne Mørtsell
2 shared publications- Gaute Svenningsen
Department of Materials Technology, Norwegian University of Science and Technology, NO-7491 Trondheim, Norway
2 shared publications - Inga D. Konow2 shared publications
Jostein Røyset
2 shared publicationsKemal Nisancioglu
2 shared publicationsMagnus Hurlen Larsen
Department of Materials Technology, Norwegian University of Science and Technology, NO-7491 Trondheim, Norway
2 shared publications
Latest Publications
- Open Access
- 20 November 2026
- Published by Elsevier in Journal of Alloys and Compounds
The synergistic effect of copper and thermomechanical processing on the corrosion behaviour of Al-Mg-Si-(Cu) alloys
- 20 November 2026
- Published by Elsevier in Journal of Alloys and Compounds
Open AccessThe synergistic effect of copper and thermomechanical processing on the corrosion behaviour of Al-Mg-Si-(Cu) alloys
- Open Access
- 5 October 2026
- Published by Elsevier in Corrosion Science
- Vol. 273
Effect of pre-aging and deformation on Cu distribution and intergranular corrosion in Al-Mg-Si-Cu alloy
- 5 October 2026
- Published by Elsevier in Corrosion Science
- Vol. 273
Open AccessEffect of pre-aging and deformation on Cu distribution and intergranular corrosion in Al-Mg-Si-Cu alloy
- Open Access
- 29 August 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 976
Linking mechanical properties to microstructure in pre-deformed Al–Mg–Si(-Cu) alloys with variable Zn content
- 29 August 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 976
Open AccessLinking mechanical properties to microstructure in pre-deformed Al–Mg–Si(-Cu) alloys with variable Zn content
- Open Access
- 31 March 2026
- Published by Elsevier in SSRN Electronic Journal
Linking Mechanical Properties to Microstructure in Pre-Deformed Al-Mg-Si-Cu Alloys with Variable Zn Content
Pre-deformation prior to age hardening is an effective approach to increase strength in extruded 6xxx-series aluminum profiles. We systematically investigated how 0-35% pre-deformation combined with artificial ageing affects mechanical properties, precipitate characteristics, and phase evolution in AA6061, with and without 0.1 wt.% Zn. Adding Zn increased strength without reducing elongation in both the undeformed and the pre-deformed condition. For a given artificial ageing time and temperature, strength increased with deformation up to 15% strain before reaching a plateau. At higher strains, the additional work-hardening contribution appears to be counterbalanced by the faster coarsening of the precipitates. Transmission electron microscopy showed that Zn addition increased precipitate density without affecting size, raising the volume fraction. Pre-deformation also increased precipitate density, but a decrease in size resulted in a similar volume fraction as the undeformed condition. High-angle annular dark field scanning transmission electron microscopy revealed a transition from needle-like ordered phases to a mix of structurally disordered needle-like precipitates and lath-like phases. Strength modeling without phase specificity reproduced the behavior of the Zn-free alloy, including a 60 MPa contribution from work-hardening after recovery. While pre-deformation was shown to slightly reduce precipitate strengthening, work-hardening fully explained the net increase in strength.
- 31 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLinking Mechanical Properties to Microstructure in Pre-Deformed Al-Mg-Si-Cu Alloys with Variable Zn Content
Pre-deformation prior to age hardening is an effective approach to increase strength in extruded 6xxx-series aluminum profiles. We systematically investigated how 0-35% pre-deformation combined with artificial ageing affects mechanical properties, precipitate characteristics, and phase evolution in AA6061, with and without 0.1 wt.% Zn. Adding Zn increased strength without reducing elongation in both the undeformed and the pre-deformed condition. For a given artificial ageing time and temperature, strength increased with deformation up to 15% strain before reaching a plateau. At higher strains, the additional work-hardening contribution appears to be counterbalanced by the faster coarsening of the precipitates. Transmission electron microscopy showed that Zn addition increased precipitate density without affecting size, raising the volume fraction. Pre-deformation also increased precipitate density, but a decrease in size resulted in a similar volume fraction as the undeformed condition. High-angle annular dark field scanning transmission electron microscopy revealed a transition from needle-like ordered phases to a mix of structurally disordered needle-like precipitates and lath-like phases. Strength modeling without phase specificity reproduced the behavior of the Zn-free alloy, including a 60 MPa contribution from work-hardening after recovery. While pre-deformation was shown to slightly reduce precipitate strengthening, work-hardening fully explained the net increase in strength.
- Open Access
- 17 October 2022
- Published by Elsevier in Corrosion Science
- Vol. 209, 110758
Electron microscopy analysis of grain boundaries and intergranular corrosion in aged Al-Mg-Si alloy doped with 0.05 wt% Cu
- 17 October 2022
- Published by Elsevier in Corrosion Science
- Vol. 209, 110758
Open AccessElectron microscopy analysis of grain boundaries and intergranular corrosion in aged Al-Mg-Si alloy doped with 0.05 wt% Cu
- 1 June 2006
- Published by Elsevier in Corrosion Science
- Vol. 48 (6) , 1528-1543
Effect of artificial aging on intergranular corrosion of extruded AlMgSi alloy with small Cu content
- 1 June 2006
- Published by Elsevier in Corrosion Science
- Vol. 48 (6) , 1528-1543
Effect of artificial aging on intergranular corrosion of extruded AlMgSi alloy with small Cu content
- 1 January 2006
- Published by Elsevier in Corrosion Science
- Vol. 48 (1) , 258-272
Effect of high temperature heat treatment on intergranular corrosion of AlMgSi(Cu) model alloy
- 1 January 2006
- Published by Elsevier in Corrosion Science
- Vol. 48 (1) , 258-272
Effect of high temperature heat treatment on intergranular corrosion of AlMgSi(Cu) model alloy
- Open Access
- 1 January 2005
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 152 (9) , B334-B341
Characterization of Lead Enrichment on Electrochemically Active AlPb Model Alloy
Certain commercial aluminum alloys can become electrochemically activated by heat-treatment as a result of enrichment of the trace element Pb at the surface. For a better understanding of the nature of activation, Pb enrichment resulting from annealing for 1-24 h at 300-600°C in air, followed by quenching in water, was investigated on an AlPb binary model alloy, by use of electrochemical polarization, electron optical techniques, and glow discharge optical emission spectroscopy. Most of the enriched Pb was found to be near the oxide film-aluminum matrix interface, probably in solid solution with aluminum. The surface concentration reached an apparent saturation level of 0.8 wt % at 600°C, up from 20 ppm in the bulk. In addition, segregated metallic Pb particles were detected at an increasing density and size with increasing time of annealing at 600°C. However, segregation of Pb particles did not have an appreciable effect on activation. It is suggested, therefore, that the electrochemical activation is related to reduced passivity of the overlying oxide by Pb enriched in solid solution at the metal surface and ensuing pitting potential depression in the combined presence of aggressive chloride ions in the test solution.
- 1 January 2005
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 152 (9) , B334-B341
Open AccessCharacterization of Lead Enrichment on Electrochemically Active AlPb Model Alloy
Certain commercial aluminum alloys can become electrochemically activated by heat-treatment as a result of enrichment of the trace element Pb at the surface. For a better understanding of the nature of activation, Pb enrichment resulting from annealing for 1-24 h at 300-600°C in air, followed by quenching in water, was investigated on an AlPb binary model alloy, by use of electrochemical polarization, electron optical techniques, and glow discharge optical emission spectroscopy. Most of the enriched Pb was found to be near the oxide film-aluminum matrix interface, probably in solid solution with aluminum. The surface concentration reached an apparent saturation level of 0.8 wt % at 600°C, up from 20 ppm in the bulk. In addition, segregated metallic Pb particles were detected at an increasing density and size with increasing time of annealing at 600°C. However, segregation of Pb particles did not have an appreciable effect on activation. It is suggested, therefore, that the electrochemical activation is related to reduced passivity of the overlying oxide by Pb enriched in solid solution at the metal surface and ensuing pitting potential depression in the combined presence of aggressive chloride ions in the test solution.