Jianwei Teng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jianwei Teng has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Yunping Li
State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China
5 shared publications - Biaobiao Yang
IMDEA Materials Institute, c/Eric Kandel 2, Getafe, 28906 Madrid, Spain
2 shared publications Chao Li
State Key Laboratory for Powder Metallurgy, Central South University, Changsha, China
1 shared publication- Chao Li
State Key Laboratory for Powder Metallurgy, Central South University, Changsha 410083, China
1 shared publication - Jiapeng Liu
Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials Hubei Key Laboratory of Polymer Materials (Hubei University) School of Materials Science and Engineering Hubei University 430062 Wuhan PR China
1 shared publication - Lu Liu
Nanjing KathMatic Technology Co., Ltd., Nanjing 211100, China
1 shared publication
Latest Publications
- Open Access
Effect of Cold Rolling on the Mechanical Properties and Corrosion Resistance in Hydrofluoric Acid Solution of Inconel 600 Alloy
In this study, Inconel 600 alloy with reductions of 20%, 50%, and 80% was obtained through cold rolling, and the effects of plastic deformation on its mechanical properties and corrosion behavior in a hydrofluoric acid (HF) solution were systematically investigated. The results show that cold rolling induces pronounced work hardening, with both hardness and strength increasing continuously with increasing reduction, while the ductility decreases accordingly. The alloy with 80% reduction exhibits the highest strength, with an ultimate tensile strength of 1270 MPa and a yield strength of 1210 MPa. In contrast, the macroscopic corrosion resistance of the alloy in HF solution remains essentially unchanged with increasing deformation, although a slight intensification of pitting corrosion is observed. The combined effects of deformation-induced pitting and passivation enhancement resulted in retention of corrosion resistance. These findings demonstrate that appropriate control of cold rolling enables effective mechanical strengthening of Inconel 600 without significantly sacrificing its corrosion performance in aggressive fluorine containing environments.
Open AccessEffect of Cold Rolling on the Mechanical Properties and Corrosion Resistance in Hydrofluoric Acid Solution of Inconel 600 Alloy
In this study, Inconel 600 alloy with reductions of 20%, 50%, and 80% was obtained through cold rolling, and the effects of plastic deformation on its mechanical properties and corrosion behavior in a hydrofluoric acid (HF) solution were systematically investigated. The results show that cold rolling induces pronounced work hardening, with both hardness and strength increasing continuously with increasing reduction, while the ductility decreases accordingly. The alloy with 80% reduction exhibits the highest strength, with an ultimate tensile strength of 1270 MPa and a yield strength of 1210 MPa. In contrast, the macroscopic corrosion resistance of the alloy in HF solution remains essentially unchanged with increasing deformation, although a slight intensification of pitting corrosion is observed. The combined effects of deformation-induced pitting and passivation enhancement resulted in retention of corrosion resistance. These findings demonstrate that appropriate control of cold rolling enables effective mechanical strengthening of Inconel 600 without significantly sacrificing its corrosion performance in aggressive fluorine containing environments.
- Open Access
- 21 June 2024
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 34 (5) , 1571-1587
Influence of Fe content on microstructure and performance of powder metallurgy Cu–Fe alloys
- 21 June 2024
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 34 (5) , 1571-1587
Open AccessInfluence of Fe content on microstructure and performance of powder metallurgy Cu–Fe alloys
- Open Access
Tribocorrosion Behavior of NiCoCrMoCu Alloys Containing Different Carbides in Acidic Media at Various Applied Loads and Sliding Speeds
In this study, the ball-on-disk sliding wear and tribocorrosion behavior in the H2SO4 and HCl solution of NiCoCrMoCu alloys with carbon additions of 0.2, 1, 1.5, and 2 wt.% with the Al2O3 ball as a counterpart was investigated systematically. Obvious tribocorrosion antagonistic effects were found after wear in both aqueous solutions. Compared with dry sliding wear conditions, the lubrication effect of the aqueous solution significantly reduces the wear rate of the alloy, and the reduction effect in the H2SO4 aqueous solution was more obvious than that in HCl. The antagonistic effects of the 0.2C and 1C alloys decrease with the load and sliding rate, while those of the 1.5C and 2C alloys increase. The (coefficient of friction) COF and wear rate under different loads and sliding rates were analyzed using the response surface analysis (RSM) method. It was found that the COF mainly showed dependence on the sliding rate, while the wear rate showed dependence on load and sliding speed.
Open AccessTribocorrosion Behavior of NiCoCrMoCu Alloys Containing Different Carbides in Acidic Media at Various Applied Loads and Sliding Speeds
In this study, the ball-on-disk sliding wear and tribocorrosion behavior in the H2SO4 and HCl solution of NiCoCrMoCu alloys with carbon additions of 0.2, 1, 1.5, and 2 wt.% with the Al2O3 ball as a counterpart was investigated systematically. Obvious tribocorrosion antagonistic effects were found after wear in both aqueous solutions. Compared with dry sliding wear conditions, the lubrication effect of the aqueous solution significantly reduces the wear rate of the alloy, and the reduction effect in the H2SO4 aqueous solution was more obvious than that in HCl. The antagonistic effects of the 0.2C and 1C alloys decrease with the load and sliding rate, while those of the 1.5C and 2C alloys increase. The (coefficient of friction) COF and wear rate under different loads and sliding rates were analyzed using the response surface analysis (RSM) method. It was found that the COF mainly showed dependence on the sliding rate, while the wear rate showed dependence on load and sliding speed.
- 31 January 2022
- Published by Elsevier in Advanced Powder Technology
- Vol. 33 (2) , 103436
Particle size dependent Ag precipitation at different temperature and the resultant oxidation behavior of Cu-5Ag powders
- 31 January 2022
- Published by Elsevier in Advanced Powder Technology
- Vol. 33 (2) , 103436
Particle size dependent Ag precipitation at different temperature and the resultant oxidation behavior of Cu-5Ag powders