Kenji Saito
Kenji Saito has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
A. Nagata
Osaka University
1 shared publicationAlex Taylor
Facility for Rare Isotope Beams
1 shared publicationAndrei Ganshyn
Facility for Rare Isotope Beams
1 shared publicationChongho Youn
Azbil Corporation, Fujisawa, Japan
1 shared publicationChris Compton
Facility for Rare Isotope Beams
1 shared publication- Ethan Metzgar
Facility for Rare Isotope Beams
1 shared publication
Latest Publications
- Open Access
- 10 March 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29 (3)
Improved high-gradient performance for medium-velocity superconducting half-wave resonators: Surface preparation and trapped flux mitigation
A development effort to improve the performance of superconducting radio-frequency half-wave resonators (SRF HWRs) is underway at the Facility for Rare Isotope Beams (FRIB), where 220 such resonators are in operation. Our goal was to achieve an intrinsic quality factor ( Q 0 ) of ≥ 2 × 10 10 at an accelerating gradient ( E acc ) of 12 MV / m . FRIB production resonators were prepared with buffered chemical polishing. First trials of electropolishing (EP) and post-EP low-temperature baking of FRIB HWRs allowed us to reach higher gradient (15 MV/m, limited by quench) with a higher quality factor at high gradient, but Q 0 was still below our goal. Trapped magnetic flux during the Dewar test was found to be a source of Q 0 reduction. Three strategies were used to reduce the trapped flux: (i) adding a local magnetic shield (LMGS) to supplement the “global” magnetic shield around the Dewar for reduction of the ambient magnetic field; (ii) performing a “uniform cooldown” (UC) to reduce the thermoelectric currents; and (iii) using a compensation coil to further reduce the ambient field with active field cancellation (AFC). The LMGS improved the Q 0 , but not enough to reach our goal. With UC and AFC, we exceeded our goal, reaching Q 0 = 2.8 × 10 10 at E acc = 12 MV / m .
- 10 March 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29 (3)
Open AccessImproved high-gradient performance for medium-velocity superconducting half-wave resonators: Surface preparation and trapped flux mitigation
A development effort to improve the performance of superconducting radio-frequency half-wave resonators (SRF HWRs) is underway at the Facility for Rare Isotope Beams (FRIB), where 220 such resonators are in operation. Our goal was to achieve an intrinsic quality factor ( Q 0 ) of ≥ 2 × 10 10 at an accelerating gradient ( E acc ) of 12 MV / m . FRIB production resonators were prepared with buffered chemical polishing. First trials of electropolishing (EP) and post-EP low-temperature baking of FRIB HWRs allowed us to reach higher gradient (15 MV/m, limited by quench) with a higher quality factor at high gradient, but Q 0 was still below our goal. Trapped magnetic flux during the Dewar test was found to be a source of Q 0 reduction. Three strategies were used to reduce the trapped flux: (i) adding a local magnetic shield (LMGS) to supplement the “global” magnetic shield around the Dewar for reduction of the ambient magnetic field; (ii) performing a “uniform cooldown” (UC) to reduce the thermoelectric currents; and (iii) using a compensation coil to further reduce the ambient field with active field cancellation (AFC). The LMGS improved the Q 0 , but not enough to reach our goal. With UC and AFC, we exceeded our goal, reaching Q 0 = 2.8 × 10 10 at E acc = 12 MV / m .
- 28 July 2019
- Published by ASME International
Simulation of Dynamic Characteristics of Pneumatic Control Valve With Smart Valve Positioner
In this research, in order to predict the dynamic characteristics of a regulating valve, a mathematical model is proposed for a pneumatic control valve using a smart valve positioner (AVP300), and the dynamic characteristics of the control valve were simulated. We modeled the components of the control valve (i.e., nozzle flapper, pilot valve, Auto/Manual (A/M) screw, bleed orifice, pneumatic actuator, gland packing, and pressure reducing valve), and simulated the dynamic characteristics using SimulationX, a one-dimensional analysis software. For the nozzle flapper, we proposed a model that considers the influence of fluid force due to pressure change as well as the influence of the change in effective area by measuring the displacement, pressure, and flow rate of the nozzle flapper. The diaphragm chamber, which operates the pilot valve of the positioner, was made of transparent acrylic. The displacement of the pilot valve was measured by a laser displacement sensor, and its movement against pressure change was clarified. The sonic speed conductance and critical pressure ratio of the A/M screw and bleed orifice were determined experimentally and reflected in the model. In the pneumatic actuator, the effective cross-section of the diaphragm was obtained from the change in pressure and displacement. The change in volume was calculated from the experiment using a fixed chamber. The friction force of gland packing was modeled using static and dynamic friction forces. The experiment on the dynamic characteristics of valve displacement was performed with the input signal of the valve displacement set from 20% to 80%. A comparison of the experimental results of the valve displacement and simulation results showed good agreement. The simulation in this study is considered effective in predicting the dynamic characteristics of the control valve.
- 28 July 2019
- Published by ASME International
Simulation of Dynamic Characteristics of Pneumatic Control Valve With Smart Valve Positioner
In this research, in order to predict the dynamic characteristics of a regulating valve, a mathematical model is proposed for a pneumatic control valve using a smart valve positioner (AVP300), and the dynamic characteristics of the control valve were simulated. We modeled the components of the control valve (i.e., nozzle flapper, pilot valve, Auto/Manual (A/M) screw, bleed orifice, pneumatic actuator, gland packing, and pressure reducing valve), and simulated the dynamic characteristics using SimulationX, a one-dimensional analysis software. For the nozzle flapper, we proposed a model that considers the influence of fluid force due to pressure change as well as the influence of the change in effective area by measuring the displacement, pressure, and flow rate of the nozzle flapper. The diaphragm chamber, which operates the pilot valve of the positioner, was made of transparent acrylic. The displacement of the pilot valve was measured by a laser displacement sensor, and its movement against pressure change was clarified. The sonic speed conductance and critical pressure ratio of the A/M screw and bleed orifice were determined experimentally and reflected in the model. In the pneumatic actuator, the effective cross-section of the diaphragm was obtained from the change in pressure and displacement. The change in volume was calculated from the experiment using a fixed chamber. The friction force of gland packing was modeled using static and dynamic friction forces. The experiment on the dynamic characteristics of valve displacement was performed with the input signal of the valve displacement set from 20% to 80%. A comparison of the experimental results of the valve displacement and simulation results showed good agreement. The simulation in this study is considered effective in predicting the dynamic characteristics of the control valve.
- 2 August 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 795-800
Adaptive Media Switching for Future Vehicle-to-Vehicle Communication
- 2 August 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 795-800
Adaptive Media Switching for Future Vehicle-to-Vehicle Communication
- 1 January 1990
- Published by Springer Nature
- p. 69-75
An Apparatus for Evaluating Strain Effect of Critical Current in Superconducting Wires in Magnetic Fields up to 16.5 T
- 1 January 1990
- Published by Springer Nature
- p. 69-75
An Apparatus for Evaluating Strain Effect of Critical Current in Superconducting Wires in Magnetic Fields up to 16.5 T