Mohamed Abdelgawad Gebril
Research Subjects
Mohamed Abdelgawad Gebril has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Ahmad Muhammad Aziz
Universiti Kebangsaan Malaysia
1 shared publication - Amir Hossein Baghdadi
Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia
1 shared publication - Farhana Mohd Foudzi
Universiti Kebangsaan Malaysia
1 shared publication I.F. Mohamed
1 shared publication- Intan Fadhlina Mohamed
Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi, Malaysia
1 shared publication M.Z. Omar
1 shared publication
Latest Publications
- Open Access
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
EFFECT OF MICROSTRUCTURAL REFINEMENT AND TEXTURE EVOLUTION ON THE ELECTROCHEMICAL BEHAVIOR OF PLASTICALLY DEFORMED ALUMINIUM ALLOY 5052
This paper presents the corrosion behaviour of aluminium alloy 5052 (A5052 alloy) prepared by high-pressure torsion (HPT) process. The A5052 alloy, prepared in the form of a 10 mm diameter disk, was processed at room temperature using HPT machine under an applied pressure of 6 GPa for 1, 10 and 25 turns, with the rotation speed of 1 rpm. The HPT process resulted in significant grain refinement up to 150 ± 50 nm and high dislocation densities reaching up to 5.0 x 1014 m-2. These lead to the increase of the corrosion rate to 0.22 mm/year. In addition to that, texture evaluation reveals that crystallographic orientation is equally critical, where planes with texture coefficient (TC) above one, specifically (111) and (200), increase the alloy’s vulnerability to corrosion attack. The high atomic packing density of the (111) planes render it particularly susceptible to electrochemical dissolution. This study demonstrates that crystallographic texture is one of the important factors, alongside grain size and dislocation densities, in defining the corrosion behaviour of processed aluminium alloys.
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEFFECT OF MICROSTRUCTURAL REFINEMENT AND TEXTURE EVOLUTION ON THE ELECTROCHEMICAL BEHAVIOR OF PLASTICALLY DEFORMED ALUMINIUM ALLOY 5052
This paper presents the corrosion behaviour of aluminium alloy 5052 (A5052 alloy) prepared by high-pressure torsion (HPT) process. The A5052 alloy, prepared in the form of a 10 mm diameter disk, was processed at room temperature using HPT machine under an applied pressure of 6 GPa for 1, 10 and 25 turns, with the rotation speed of 1 rpm. The HPT process resulted in significant grain refinement up to 150 ± 50 nm and high dislocation densities reaching up to 5.0 x 1014 m-2. These lead to the increase of the corrosion rate to 0.22 mm/year. In addition to that, texture evaluation reveals that crystallographic orientation is equally critical, where planes with texture coefficient (TC) above one, specifically (111) and (200), increase the alloy’s vulnerability to corrosion attack. The high atomic packing density of the (111) planes render it particularly susceptible to electrochemical dissolution. This study demonstrates that crystallographic texture is one of the important factors, alongside grain size and dislocation densities, in defining the corrosion behaviour of processed aluminium alloys.
- Open Access
- 6 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 41, 715-729
Microstructural evolution and mechanical properties in thixoformed Al–Si–Cu–Mg alloy: An EBSD-based study
- 6 December 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 41, 715-729
Open AccessMicrostructural evolution and mechanical properties in thixoformed Al–Si–Cu–Mg alloy: An EBSD-based study