PDPavel V. Dushkin

Pavel V. Dushkin

*This is an algorithmically generated author record based on publicly available information.

Pavel V. Dushkin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Air-fuel ratio control method based on the modified proportional-integral controller and the Smith predictor

    by Pavel V. Dushkin, Vladislav Vladimirovich Kremnev, Sergey Sergeevich Khovrenok

    BACKGROUND: To meet modern emission standards for spark-ignition engines, it is necessary to maintain a stoichiometric air-fuel ratio (α=1.000) or an enriched mixture (α=0.995–0.999). To improve the precision of air-fuel ratio (AFR) control, feedback controller utilizing data from a lambda sensor, which is mounted in the exhaust system of the internal combustion engine (ICE), is employed. For stable and fast operation of this controller, the use of a standard proportional-integral (PI) control law is limited. This is due to the significant time delay between changes in the AFR in the ICE cylinder and the lambda sensor response. The time delay leads to over-accumulation of the integral component and, as a result, incorrect operation of the regulator. AIM: Improvement of the accuracy of maintaining the air-fuel ratio (AFR, α) in the cylinder of the internal combustion engine through closed-loop control using a lambda sensor during transient modes. METHODS: To achieve this aim, the proportional-integral controller has been modified with an exhaust system model that predicts the air-fuel ratio response to control actions — changes in the fuel supply quantity. This control approach is known as the Smith predictor. The research methodology is comprehensive. The main theoretical provisions were obtained through an analytical review, then verified using computational modeling, implemented for the internal combustion engine control system, and tested during engine test-bench trials. RESULTS: The main results were obtained for the two spark-ignition engines: 4.4-liter V8 and 1.5-liter 4 cylinder. Both engines equipped by turbocharger and direct injection fuel system. The possible values of the exhaust system’s dynamic properties were demonstrated. For example, the time constant and delay for the operating mode — n=1500 RPM and relative air charge 0.3 can be T=0.23 s and θ=0.21 s. This leads to prolonged transient processes and overshoot when changing the target air-fuel ratio. It was found that thanks to the controller developed during the research, it is possible to eliminate the overshoot completely as well as to reduce the transient process time by 1.6 times. CONCLUSION: The developed method for controlling the air-fuel ratio has confirmed its functional safety and effectiveness through the engine tests. This method can be utilized for the ICE control system of a vehicle. The results are most relevant for turbocharged spark-ignition engines with a wideband lambda sensor, but they can also be applied to diesel engines or spark-ignition engines with a threshold lambda sensor.

  • Automation of an automobile internal combustion engine bench calibration tests

    by E. S. Evdonin, P. V. Dushkin, A. И. Кузьмин, S. S. Khovrenok, V. V. Kremnev

    Введение (постановка задачи и актуальность). В статье представлены результаты работы по автоматизации калибровочных испытаний двигателя внутреннего сгорания (ДВС) на моторном стенде. Актуальность статьи обусловлена высокой трудоёмкостью таких испытаний, сложностью документирования и принятия решений по итогам работы. Цель исследования. Данная работа – один из элементов комплексной методики, цель которой – сокращение продолжительности испытаний и повышение качества результатов калибровки силовой установки автомобиля. Описание всей методики в целом также приводится в публикации. Методология и методы. Достижение поставленной цели обеспечивается с помощью специальных систем – INCA-FLOW (автоматизация испытаний) и ASCMO (обработка результатов и оптимизация), выпускаемых фирмой Bosch/ETAS. Апробация методики проведена на моторном стенде в учебном боксе МАДИ применительно к задаче формирования карты углов опережения зажигания. Результаты и научная новизна. В результате применения методики показано сокращение продолжительности моторных испытаний в 4,8 раза, если в ручном режиме за стендом работают 2 человека без перерыва. При этом дисперсия адекватности Sад эмпирической модели крутящего момента Мк оказалась в среднем в 1,5 раза меньше, если модель построена по результатам автоматизированных испытаний. Это говорит и об улучшении качества измерений при переходе к автоматизированным методам испытаний. С научной точки зрения, наиболее оригинальная часть работы, это применение метода «Гауссовский процесс» для построения эмпирических моделей. Данный метод позволяет получать более точные результаты, чем, например, традиционный метод наименьших квадратов. Практическая значимость работы заключается в возможности существенно сократить рутинные действия на моторном стенде, а дополнительные временные затраты на разработку и тестирование сценария (программы) испытаний компенсируются за счёт того, что макеты сценариев могут быть в дальнейшем использованы для других аналогичных испытаний. Представленная методика позволяет охватить значительную часть калибровочных испытаний ДВС. Например, когда известны предварительные сведения об объекте испытаний (опираясь на которые можно составить план эксперимента) и двигатель необходимо подготовить к дорожным испытаниям на автомобиле или в особых условиях.


  • Open Access

    INFLUENCE OF PRESSURE OSCILLATIONS IN COMMON RAIL INJECTOR ON FUEL INJECTION RATE

    by Mikhail G. Shatrov, Andrey U. Dunin, Pavel V. Dushkin, Andrey L. Yakovenko, Leonid N. Golubkov, Vladimir V. Sinyavski

    Fuel injection causes considerable oscillations of fuel pressure at the injector inlet. One of the reasons is hydraulic impact when the needle valve closes. For multiple injections, the previous injections affect the following. As both the fuel pressure in rail pac and the injection rate grow, the oscillations increase. The pressure oscillation range at the common rail injector inlet at pac=1500 bar is up to 350 bar, and at the rail pressure pac=500 bar, the amplitude decreases to 80 bar. Physical properties of the fuel are also important. As the viscosity of the fuel increases, its hydraulic friction grows which results in a rapid damping of pressure oscillations. The data for an injector operating on sunflower oil is presented. As compared with diesel fuel, the oscillations range decreases from 400 to 250 bar at the same operating mode. The influence of the interval between the impulses of a double injection on the injection rate of the second fuel portion was investigated. Superposition of two waves during multiple injections may result in amplification and damping of the oscillations. Simulation was performed to estimate the influence of fuel type and time interval Δτ between control impulses of a double injection on the injection quantity of the second portion at pressures of 2000-3000 bar. When the rail pressure pac grows, the oscillations and their impact on the injection process increase. For diesel fuel at pressure of pac=2000 bar, the variation in injection rates of the second portion is 2.36-4.62 mg, and at pac=3000 bar – 1.58-6.63 mg.